Junho Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Junho Lee has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Yeojoon Yoon
Department of Environmental and Energy Engineering, Yonsei University, Wonju, 26493, Republic of Korea
8 shared publications - Chaehwi Lim
Department of Environmental and Energy Engineering, Yonsei University, Wonju, 26493, Republic of Korea
6 shared publications - Seonghyeon Ju
Department of Environmental and Energy Engineering, Yonsei University, Wonju, 26493, Republic of Korea
5 shared publications - Jihoon Lee
Department of Environmental and Energy Engineering, Yonsei University, Wonju, 26493, Republic of Korea
3 shared publications Jiyoon Kim
2 shared publications- Namgyu Kim
Department of Environmental and Energy Engineering, Yonsei University, 1 Yonseidae-gil, Wonju 26493, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 8 February 2025
- Published by Elsevier in Carbon Trends
- Vol. 19
Comparative evaluation of cationic and anionic dye removal using graphene oxide fabricated by Hummers and Couette-Taylor flow methods
- 8 February 2025
- Published by Elsevier in Carbon Trends
- Vol. 19
Open AccessComparative evaluation of cationic and anionic dye removal using graphene oxide fabricated by Hummers and Couette-Taylor flow methods
- Open Access
- 26 July 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (33) , 24212
Correction: Evaluating the dispersibility of rGO prepared using a solvothermal method with DMF and its application as a CDI electrode material: recovery of sp2-hybridized carbon
Correction for ‘Evaluating the dispersibility of rGO prepared using a solvothermal method with DMF and its application as a CDI electrode material: recovery of sp2-hybridized carbon’ by Junho Lee et al., RSC Adv., 2024, 14, 22665–22675, https://doi.org/10.1039/D4RA03387F.
- 26 July 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (33) , 24212
Open AccessCorrection: Evaluating the dispersibility of rGO prepared using a solvothermal method with DMF and its application as a CDI electrode material: recovery of sp2-hybridized carbon
Correction for ‘Evaluating the dispersibility of rGO prepared using a solvothermal method with DMF and its application as a CDI electrode material: recovery of sp2-hybridized carbon’ by Junho Lee et al., RSC Adv., 2024, 14, 22665–22675, https://doi.org/10.1039/D4RA03387F.
- Open Access
- 12 July 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (31) , 22665-22675
Effect of a solvothermal method using DMF on the dispersibility of rGO, application of rGO as a CDI electrode material, and recovery of sp 2 -hybridized carbon
To improve the low dispersibility of rGO, solvothermal reduction was applied with N , N -dimethylformamide and the electrochemical performance was measured.
- 12 July 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (31) , 22665-22675
Open AccessEffect of a solvothermal method using DMF on the dispersibility of rGO, application of rGO as a CDI electrode material, and recovery of sp 2 -hybridized carbon
To improve the low dispersibility of rGO, solvothermal reduction was applied with N , N -dimethylformamide and the electrochemical performance was measured.
- Top Cited PapersOpen Access
Microplastics in water systems: A review of their impacts on the environment and their potential hazards
Top Cited PapersOpen AccessMicroplastics in water systems: A review of their impacts on the environment and their potential hazards
- Open Access
- 21 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (5) , 3907
High-Efficiency Microplastic Sampling Device Improved Using CFD Analysis
Since microplastics are considered harmful to the human body, studies on their samplings, pretreatments and analyses environmental media, such as water, are continuously being conducted. However, a standard sampling and pretreatment method must be established, particularly because microplastics of a few micrometers in size are easily affected by external contamination. In this study, a microplastic sampling device was designed and developed to obtain a high recovery rate of microplastics and prevent plastics contamination during all processes. For the evaluation of the developed device, microplastic reference materials were produced and used, and computational fluid dynamics (CFD) analysis was performed. This device has not only been applied to the relatively large previously studied microplastics (100 µm) but also to microplastics of approximately 20 µm that are vulnerable to contamination. A recovery rate of 94.2% was obtained using this device, and the particles were separated by filtration through a three-stage cassette. In conclusion, we propose a method to increase the accuracy and reproducibility of results for microplastic contamination in the environment. This method is able to consistently obtain and manage microplastics data, which are often difficult to compare using various existing methods.
- 21 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (5) , 3907
Open AccessHigh-Efficiency Microplastic Sampling Device Improved Using CFD Analysis
Since microplastics are considered harmful to the human body, studies on their samplings, pretreatments and analyses environmental media, such as water, are continuously being conducted. However, a standard sampling and pretreatment method must be established, particularly because microplastics of a few micrometers in size are easily affected by external contamination. In this study, a microplastic sampling device was designed and developed to obtain a high recovery rate of microplastics and prevent plastics contamination during all processes. For the evaluation of the developed device, microplastic reference materials were produced and used, and computational fluid dynamics (CFD) analysis was performed. This device has not only been applied to the relatively large previously studied microplastics (100 µm) but also to microplastics of approximately 20 µm that are vulnerable to contamination. A recovery rate of 94.2% was obtained using this device, and the particles were separated by filtration through a three-stage cassette. In conclusion, we propose a method to increase the accuracy and reproducibility of results for microplastic contamination in the environment. This method is able to consistently obtain and manage microplastics data, which are often difficult to compare using various existing methods.
- Open Access
Potential of Adsorption of Diverse Environmental Contaminants onto Microplastics
Microplastics are regarded as vectors of hazardous contaminants due to their ability to adsorb xenobiotic chemicals. This has led to increased interest in the risk of previously neglected microplastic contaminants in the aquatic environment. Here, we assessed the possibility of transferring chemical contaminants to microplastics by evaluating the adsorption performance of (in)organic pollutants on various types of microplastics (polystyrene, PS; polyethylene terephthalate, PET; high-density polyethylene, HDPE; and low-density polyethylene, LDPE;). Considering the toxicity and polarity of each pollutant, dyes (BB9 and RR120) and heavy metals (Cd(II), Pb(II), As(III), and As(V)) were selected for the adsorption experiments. Dye was found to be adsorbed through physical adsorption. The adsorption capacity of microplastics for RR120 and BB9 was the highest for HDPE-1 and LDPE-1, respectively. Additionally, the smaller the size of the microplastics, the higher the adsorbed amounts. The main adsorption mechanism of heavy metals was found to be through physical and chemical adsorption. And adsorption mechanism of dye depends on physical adsorption. Thus, the adsorption of microplastic contaminants was affected more by the condition than by the type of microplastics.
Open AccessPotential of Adsorption of Diverse Environmental Contaminants onto Microplastics
Microplastics are regarded as vectors of hazardous contaminants due to their ability to adsorb xenobiotic chemicals. This has led to increased interest in the risk of previously neglected microplastic contaminants in the aquatic environment. Here, we assessed the possibility of transferring chemical contaminants to microplastics by evaluating the adsorption performance of (in)organic pollutants on various types of microplastics (polystyrene, PS; polyethylene terephthalate, PET; high-density polyethylene, HDPE; and low-density polyethylene, LDPE;). Considering the toxicity and polarity of each pollutant, dyes (BB9 and RR120) and heavy metals (Cd(II), Pb(II), As(III), and As(V)) were selected for the adsorption experiments. Dye was found to be adsorbed through physical adsorption. The adsorption capacity of microplastics for RR120 and BB9 was the highest for HDPE-1 and LDPE-1, respectively. Additionally, the smaller the size of the microplastics, the higher the adsorbed amounts. The main adsorption mechanism of heavy metals was found to be through physical and chemical adsorption. And adsorption mechanism of dye depends on physical adsorption. Thus, the adsorption of microplastic contaminants was affected more by the condition than by the type of microplastics.
- 10 October 2022
- Published by Elsevier in Environmental Pollution
- Vol. 315, 120402
Development of selective mercury recovery technology by using iron iodide from waste sludge of non-ferrous metal smelting process
- 10 October 2022
- Published by Elsevier in Environmental Pollution
- Vol. 315, 120402
Development of selective mercury recovery technology by using iron iodide from waste sludge of non-ferrous metal smelting process
- Open Access
- 1 January 2010
- Published by Korean Society of Occupational & Environmental Medicine in Korean Journal of Occupational and Environmental Medicine
- Vol. 22 (3) , 271-277
A Case of Lead Poisoning by Ingesting Herbal Pills Tainted by Lead during the Manufacturing Process
Shin YH, et al. Korean J Occup Environ Med. 2010 Sep;22(3):271-277. https://doi.org/10.35371/kjoem.2010.22.3.271
- 1 January 2010
- Published by Korean Society of Occupational & Environmental Medicine in Korean Journal of Occupational and Environmental Medicine
- Vol. 22 (3) , 271-277
Open AccessA Case of Lead Poisoning by Ingesting Herbal Pills Tainted by Lead during the Manufacturing Process
Shin YH, et al. Korean J Occup Environ Med. 2010 Sep;22(3):271-277. https://doi.org/10.35371/kjoem.2010.22.3.271