RCRicardo Correia

Ricardo Correia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ricardo Correia has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Elvira Fortunato

    CENIMAT|i3N, Department of Materials Science, School of Science and Technology, NOVA University Lisbon and CEMOP/UNINOVA, 2829-516 Caparica, Portugal

    3 shared publications
  • João Coelho

    CENIMAT|i3N, Department of Materials Science, Faculty of Science and Technology, Universidade NOVA de Lisboa and CEMOP/UNINOVA, Campus da Caparica, Caparica, 2829-516, Portugal

    3 shared publications
  • Rodrigo Martins

    CENIMAT|i3N, Department of Materials Science, School of Science and Technology, NOVA University Lisbon and CEMOP/UNINOVA, 2829-516 Caparica, Portugal

    3 shared publications
  • Ana Carolina Marques

    CENIMAT/i3N, Materials Science Department, NOVA School of Science and Technology, NOVA University Lisbon, 2819-516 Caparica, Portugal

    2 shared publications
  • Joana Vaz Pinto

    Centro de Investigação de Materiais—CENIMAT|i3N, Department of Materials Science, School of Science and Technology, NOVA University Lisbon and Centro de Excelência de Microelectrónica e Optoelectrónica de Processos—CEMOP/UNINOVA, Campus de Caparica, 2829-516 Caparica, Portugal

    2 shared publications
  • Maria Rosario Correia

    Universidade de Aveiro

    2 shared publications

Latest Publications

  • Open Access

    Paper-based laser-induced graphene for sustainable and flexible microsupercapacitor applications

    by João Coelho, Ricardo F. Correia, Sara Silvestre, Tomás Pinheiro, Ana C. Marques, M. Rosário P. Correia, Joana Vaz Pinto, Elvira Fortunato, Rodrigo Martins

    Laser-induced graphene (LIG) is as a promising material for flexible microsupercapacitors (MSCs) due to its simple and cost-effective processing. However, LIG-MSC research and production has been centered on non-sustainable polymeric substrates, such as polyimide. In this work, it is presented a cost-effective, reproducible, and robust approach for the preparation of LIG structures via a one-step laser direct writing on chromatography paper. The developed strategy relies on soaking the paper in a 0.1 M sodium tetraborate solution (borax) prior to the laser processing. Borax acts as a fire-retardant agent, thus allowing the laser processing of sensitive substrates that other way would be easily destroyed under the high-energy beam. LIG on paper exhibiting low sheet resistance (30 Ω sq−1) and improved electrode/electrolyte interface was obtained by the proposed method. When used as microsupercapacitor electrodes, this laser-induced graphene resulted in specific capacitances of 4.6 mF cm−2 (0.015 mA cm−2). Furthermore, the devices exhibit excellent cycling stability (> 10,000 cycles at 0.5 mA cm−2) and good mechanical properties. By connecting the devices in series and parallel, it was also possible to control the voltage and energy delivered by the system. Thus, paper-based LIG-MSC can be used as energy storage devices for flexible, low-cost, and portable electronics. Additionally, due to their flexible design and architecture, they can be easily adapted to other circuits and applications with different power requirements. Graphical Abstract


  • Open Access

    Water Peel-Off Transfer of Electronically Enhanced, Paper-Based Laser-Induced Graphene for Wearable Electronics

    by Tomás Pinheiro, Ricardo Correia, Maria Morais, João Coelho, Elvira Fortunato, M. Goreti F. Sales, Ana C. Marques, Rodrigo Martins

    Laser-induced graphene (LIG) has gained preponderance in recent years, as a very attractive material for the fabrication and patterning of graphitic structures and electrodes, for multiple applications in electronics. Typically, polymeric substrates, such as polyimide, have been used as precursor materials, but other organic, more sustainable, and accessible precursor materials have emerged as viable alternatives, including cellulose substrates. However, these substrates have lacked the conductive and chemical properties achieved by conventional LIG precursor substrates and have not been translated into fully flexible, wearable scenarios. In this work, we expand the conductive properties of paper-based LIG, by boosting the graphitization potential of paper, through the introduction of external aromatic moieties and meticulous control of laser fluence. Colored wax printing over the paper substrates introduces aromatic chemical structures, allowing for the synthesis of LIG chemical structures with sheet resistances as low as 5 Ω·sq-1, translating to an apparent conductivity as high as 28.2 S·cm-1. Regarding chemical properties, ID/IG ratios of 0.28 showcase low defect densities of LIG chemical structures and improve on previous reports on paper-based LIG, where sheet resistance has been limited to values around 30 Ω·sq-1, with more defect dense and less crystalline chemical structures. With these improved properties, a simple transfer methodology was developed, based on a water-induced peel-off process that efficiently separates patterned LIG structures from the native paper substrates to conformable, flexible substrates, harnessing the multifunctional capabilities of LIG toward multiple applications in wearable electronics. Proof-of concept electrodes for electrochemical sensors, strain sensors, and in-plane microsupercapacitors were patterned, transferred, and characterized, using paper as a high-value LIG precursor for multiples scenarios in wearable technologies, for improved sustainability and accessibility of such applications.


  • Open Access

    Biocompatible Parylene-C Laser-Induced Graphene Electrodes for Microsupercapacitor Applications

    by Ricardo Correia, Jonas Deuermeier, Maria Rosário Correia, Joana Vaz Pinto, João Coelho, Elvira Fortunato, Rodrigo Martins

    Laser irradiation of polymeric materials has drawn great attention as a fast, simple, and cost-effective method for the formation of porous graphene films that can be subsequently fabricated into low-cost and flexible electronic and energy-storage devices. In this work, we report a systematic study of the formation of laser-induced graphene (LIG) with sheet resistances as low as 9.4 Ω/sq on parylene-C ultrathin membranes under a CO2 infrared laser. Raman analysis proved the formation of the multilayered graphenic material, with ID/IG and I2D/IG peak ratios of 0.42 and 0.65, respectively. As a proof of concept, parylene-C LIG was used as the electrode material for the fabrication of ultrathin, solid-state microsupercapacitors (MSCs) via a one-step, scalable, and cost-effective approach, aiming at future flexible and wearable applications. The produced LIG-MSC on parylene-C exhibited good electrochemical behavior, with a specific capacitance of 1.66 mF/cm2 and an excellent cycling stability of 96% after 10 000 cycles (0.5 mA/cm2). This work allows one to further extend the knowledge in LIG processes, widening the group of precursor materials as well as promoting future applications. Furthermore, it reinforces the potential of parylene-C as a key material for next-generation biocompatible and flexible electronic devices.