Mbelle Samuel Bisong
Research Subjects
Mbelle Samuel Bisong has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Andy Mbeng
Department of Mechanical Engineering, ENSET Kumba, University of Buea, P.O. Box: 249, Kumba, Cameroon
1 shared publication- Claude Takoumbe
Department of Mechanical Engineering, ENSET, University of Douala, P.O. Box: 1872, Douala, Cameroon
1 shared publication - Elvis Mbou Tiaya
Mechanics and Adapted Materials Laboratory (LAMMA), ENSET, University of Douala, Douala, Cameroun
1 shared publication - Francois Njock Bayock
University of Douala
1 shared publication Honore Tchoumeni Tchami
1 shared publicationJacqueline Mefoung Djoukouo
1 shared publication
Latest Publications
- Open Access
- 17 January 2026
- Published by Wiley in Advances in Polymer Technology
- Vol. 2026 (1)
Physical, Mechanical and Thermal Properties of an Epoxy Composite Reinforced With Nauclea diderrichii (Bilinga) Wood Particles
Developing new materials by recovering waste materials in the polymer reinforcement process helps to protect the environment and ensure a circular economy for these waste materials when they reach the end of their life cycle. This study shows the possibility of developing a new composite with bilinga and epoxy resin waste. Composites were realised by using cold pressure moulding technique with different pressures, particle sizes and reinforcement rate. Physical tests were carrying out to determine moisture content, water absorption rate and density by using a gravimetric method. Three‐point bending tests were used to determine flexural Young modulus and maximum break stress. Asymmetric Hot plane method with insulated rear face were used to determine thermal conductivity of composites. Results obtained show that moisture content varies from 2.3% to 6.65% and water absorption rate from 61% to 191%. These results allow us to say that this composite material has a hydrophilicity character. Young’s modulus of these materials is between 117 and 1951 MPa. Breaking stress of these composite materials is between 0.5 and 12.5 MPa. Results show that increasing compaction pressure also increases the mechanical properties of composite, as shown by standard EN312 for used in dry and humid environments. The thermal conductivity of the composite in between 0.18 and 0.27 W m −1 K −1 . These results confirm that the composite materials produced can be used in furniture manufacturing, thermal insulation for homes and ceilings, and the development of sandwich materials.
- 17 January 2026
- Published by Wiley in Advances in Polymer Technology
- Vol. 2026 (1)
Open AccessPhysical, Mechanical and Thermal Properties of an Epoxy Composite Reinforced With Nauclea diderrichii (Bilinga) Wood Particles
Developing new materials by recovering waste materials in the polymer reinforcement process helps to protect the environment and ensure a circular economy for these waste materials when they reach the end of their life cycle. This study shows the possibility of developing a new composite with bilinga and epoxy resin waste. Composites were realised by using cold pressure moulding technique with different pressures, particle sizes and reinforcement rate. Physical tests were carrying out to determine moisture content, water absorption rate and density by using a gravimetric method. Three‐point bending tests were used to determine flexural Young modulus and maximum break stress. Asymmetric Hot plane method with insulated rear face were used to determine thermal conductivity of composites. Results obtained show that moisture content varies from 2.3% to 6.65% and water absorption rate from 61% to 191%. These results allow us to say that this composite material has a hydrophilicity character. Young’s modulus of these materials is between 117 and 1951 MPa. Breaking stress of these composite materials is between 0.5 and 12.5 MPa. Results show that increasing compaction pressure also increases the mechanical properties of composite, as shown by standard EN312 for used in dry and humid environments. The thermal conductivity of the composite in between 0.18 and 0.27 W m −1 K −1 . These results confirm that the composite materials produced can be used in furniture manufacturing, thermal insulation for homes and ceilings, and the development of sandwich materials.
- Open Access
- 5 April 2023
- Published by Academy of Sciences of the Republic of Sakha (Yakutia) in ARCTIC AND SUBARCTIC NATURAL RESOURCES
- Vol. 28 (1) , 156-171
Foundation of multilevel apploach to fracture modeling for materials with submicrostructure applicable for Arctic and Subarctic environment
A short review of research on multiscale modeling of the fracture processes of heterogeneous materials with submicrostructures applicable to Arctic and Subarctic environments is presented. The results of solving a number of model problems, both in terms of macroscopic strength and main crack growth, and describing the accumulation of microscopic defects and hierarchical fracture processes by the mechanisms of formation, growth, and fusion of secondary and microcracks, and microscopic pores are provided. Thus, for the fracture process of samples of porous concrete modified with oil palm fruit fibers to improve its consumer qualities, a simulation of crack growth was conducted, which showed a decrease in the crack resistance of the material with increasing fiber content. A three-point bend test was used to evaluate the bending strength and modulus of elasticity, and the compressive strength and modulus of elasticity were determined. An increase in the fiber content led to a decrease in the compressive strength and modulus of elasticity. The fracture surface analysis revealed the mechanism of crack propagation through the coalescence of micropores. The basis of the modeling was an experimentally substantiated criterion for concentrated fractures during crack formation based on percolation theory. Macroscopic finite-element and stochastic modeling of fractures during the bending of a beam made of wood have also been carried out. For wooden structures, the peculiarity is the anisotropic behavior of the material in the loading direction. The structure of the Bilinga tree timber at the mesoscopic and microscale levels was considered, and a hierarchy of the spatial and temporal scales of the fracture process was constructed. The crack growth rates at different scales were determined and compared with macroscopic FE simulations. Another task was to determine the dependence of the crack growth rate in the soil, such as regolith, under the influence of an ultrasonic impactor. Stochastic modeling of the crack growth in the array of micropores revealed the crack growth rate dependence on the ultrasonic transmitter beater parameters and pulse amplitude.
- 5 April 2023
- Published by Academy of Sciences of the Republic of Sakha (Yakutia) in ARCTIC AND SUBARCTIC NATURAL RESOURCES
- Vol. 28 (1) , 156-171
Open AccessFoundation of multilevel apploach to fracture modeling for materials with submicrostructure applicable for Arctic and Subarctic environment
A short review of research on multiscale modeling of the fracture processes of heterogeneous materials with submicrostructures applicable to Arctic and Subarctic environments is presented. The results of solving a number of model problems, both in terms of macroscopic strength and main crack growth, and describing the accumulation of microscopic defects and hierarchical fracture processes by the mechanisms of formation, growth, and fusion of secondary and microcracks, and microscopic pores are provided. Thus, for the fracture process of samples of porous concrete modified with oil palm fruit fibers to improve its consumer qualities, a simulation of crack growth was conducted, which showed a decrease in the crack resistance of the material with increasing fiber content. A three-point bend test was used to evaluate the bending strength and modulus of elasticity, and the compressive strength and modulus of elasticity were determined. An increase in the fiber content led to a decrease in the compressive strength and modulus of elasticity. The fracture surface analysis revealed the mechanism of crack propagation through the coalescence of micropores. The basis of the modeling was an experimentally substantiated criterion for concentrated fractures during crack formation based on percolation theory. Macroscopic finite-element and stochastic modeling of fractures during the bending of a beam made of wood have also been carried out. For wooden structures, the peculiarity is the anisotropic behavior of the material in the loading direction. The structure of the Bilinga tree timber at the mesoscopic and microscale levels was considered, and a hierarchy of the spatial and temporal scales of the fracture process was constructed. The crack growth rates at different scales were determined and compared with macroscopic FE simulations. Another task was to determine the dependence of the crack growth rate in the soil, such as regolith, under the influence of an ultrasonic impactor. Stochastic modeling of the crack growth in the array of micropores revealed the crack growth rate dependence on the ultrasonic transmitter beater parameters and pulse amplitude.
- Open Access
- 17 October 2022
- Published by Wiley in International Journal of Polymer Science
- Vol. 2022, 1-9
Physico-Mechanical Characterization of Plastic (Polyester) Reinforce With Palm Kernel Shell
The main objective of this research paper is to contribute to the characterization of a composite material with a polymer matrix reinforced with a palm kernel shell fiber for its application in the naval or aeronautic industry. To achieve this objective, it first opted for the fabrication of this composite by molding with different grain sizes (0.5mm and 1.25mm) and at different percentages of sand and PVC with the following proportions: (10, 20, 30, and 40), then subjected the sample pieces to physical and mechanical testing such as (three-point bendings, resilience and compression tests). The physical characterization allows us to obtain an experimental volumetric mass for the 0.5mm sample varying between 1.72 and 1.59kg/m3 and for the sample 1.25mm, varying between 1.66 and 1.61kg/m3 that is the more the percentage of palm kernel powder increases, the lighter our material becomes. The mechanical characterization shows a Youngs modulus in bending varying between 3199.06 and 3236.16MPa for the 0.5mm and from 31,881.87 to 3244.03MPa for 1.25mm that is the palm kernel powder and grain size make the material more rigid, normal stress due to compression varying between 32.05 and 56.41MPa for 0.5mm and from 44.8246 to 62.028MPa for 1.25mm. A resilience test varies between 0.61 and 2.00J/cm2 for 0.5mm and from 0.94 to 2.39J/cm2 for 1.25mm that is the more the percentage of palm kernel shell and particle size, the more the material becomes more resilient.
- 17 October 2022
- Published by Wiley in International Journal of Polymer Science
- Vol. 2022, 1-9
Open AccessPhysico-Mechanical Characterization of Plastic (Polyester) Reinforce With Palm Kernel Shell
The main objective of this research paper is to contribute to the characterization of a composite material with a polymer matrix reinforced with a palm kernel shell fiber for its application in the naval or aeronautic industry. To achieve this objective, it first opted for the fabrication of this composite by molding with different grain sizes (0.5mm and 1.25mm) and at different percentages of sand and PVC with the following proportions: (10, 20, 30, and 40), then subjected the sample pieces to physical and mechanical testing such as (three-point bendings, resilience and compression tests). The physical characterization allows us to obtain an experimental volumetric mass for the 0.5mm sample varying between 1.72 and 1.59kg/m3 and for the sample 1.25mm, varying between 1.66 and 1.61kg/m3 that is the more the percentage of palm kernel powder increases, the lighter our material becomes. The mechanical characterization shows a Youngs modulus in bending varying between 3199.06 and 3236.16MPa for the 0.5mm and from 31,881.87 to 3244.03MPa for 1.25mm that is the palm kernel powder and grain size make the material more rigid, normal stress due to compression varying between 32.05 and 56.41MPa for 0.5mm and from 44.8246 to 62.028MPa for 1.25mm. A resilience test varies between 0.61 and 2.00J/cm2 for 0.5mm and from 0.94 to 2.39J/cm2 for 1.25mm that is the more the percentage of palm kernel shell and particle size, the more the material becomes more resilient.