Claude Takoumbe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Claude Takoumbe has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
Elvis Mbou Tiaya
ENSET – University of Douala, Douala, Cameroon
5 shared publicationsEbenezer Njeugna
ENSET – University of Douala, Douala, Cameroon
4 shared publications- Jean Aimé Mono
Basic Science Department, Advanced Technical Teacher Training School, University of Douala, Cameroon
3 shared publications - Jonas Peequeur Essome Mbang
Mechanic Laboratory (LM), Doctoral Training Unit in Engineering Sciences (UFD-SI), University of Douala, Douala, Cameroun
3 shared publications Odette Thérèse Adegono Assiene
3 shared publications- Achille Bernard Biwolé
University of Douala
2 shared publications
Latest Publications
- 28 May 2026
- Published by SAGE Publications in Progress in Rubber, Plastics and Recycling Technology
Development of a dissolved polystyrene matrix composite reinforced with coconut fibre particles
A new sustainable and environmentally friendly composite material has been developed from coconut fibre particles and recycled polystyrene dissolved in chloroform. Three particle sizes and four reinforcement ratios were used. The composite was moulded by cold pressing without measuring the pressure but by fixing the thickness. The density (592.53 – 723.03) kg.m -3 shows the lightness of the material. The moisture content (6.63 – 8.35%), water absorption rate (54.06 – 109.42) % and thickness swelling rate (2.86 – 16.09) % are within the acceptable range of ≤16% for use in dry and wet areas, except for formulations with a 55% reinforcement rate. The absorption kinetics of the composites produced show hydrophilicity and correlate with Page’s model. Microscopic examination shows better interfacial cohesion with low visible porosity for composites with the lowest particle content and reinforcement rate. Young’s modulus (129.29 – 530.95) MPa and mechanical stress at break (1.26 – 6.508) MPa are relatively low compared to structural materials. Thermal conductivity (0.22 – 0.347) W.m -1 .k -1 and thermal effusivity (571.9 – 856.7) J.m -2 .K -1 .S -1/2 are within the range of thermally insulating materials. Smaller particles show better cohesion with the matrix. These materials are intended for use in furniture, false ceilings, house partitions, computer stands and telephone booth doors.
- 28 May 2026
- Published by SAGE Publications in Progress in Rubber, Plastics and Recycling Technology
Development of a dissolved polystyrene matrix composite reinforced with coconut fibre particles
A new sustainable and environmentally friendly composite material has been developed from coconut fibre particles and recycled polystyrene dissolved in chloroform. Three particle sizes and four reinforcement ratios were used. The composite was moulded by cold pressing without measuring the pressure but by fixing the thickness. The density (592.53 – 723.03) kg.m -3 shows the lightness of the material. The moisture content (6.63 – 8.35%), water absorption rate (54.06 – 109.42) % and thickness swelling rate (2.86 – 16.09) % are within the acceptable range of ≤16% for use in dry and wet areas, except for formulations with a 55% reinforcement rate. The absorption kinetics of the composites produced show hydrophilicity and correlate with Page’s model. Microscopic examination shows better interfacial cohesion with low visible porosity for composites with the lowest particle content and reinforcement rate. Young’s modulus (129.29 – 530.95) MPa and mechanical stress at break (1.26 – 6.508) MPa are relatively low compared to structural materials. Thermal conductivity (0.22 – 0.347) W.m -1 .k -1 and thermal effusivity (571.9 – 856.7) J.m -2 .K -1 .S -1/2 are within the range of thermally insulating materials. Smaller particles show better cohesion with the matrix. These materials are intended for use in furniture, false ceilings, house partitions, computer stands and telephone booth doors.
- 17 April 2026
- Published by Springer Nature in Journal of the Indian Academy of Wood Science
- Vol. 23 (1) , 160-180
Using Fraké (Terminalia superba) wood waste to manufacture epoxy matrix composites for sustainable development
- 17 April 2026
- Published by Springer Nature in Journal of the Indian Academy of Wood Science
- Vol. 23 (1) , 160-180
Using Fraké (Terminalia superba) wood waste to manufacture epoxy matrix composites for sustainable development
- Open Access
- 17 January 2026
- Published by Wiley in Advances in Polymer Technology
- Vol. 2026 (1)
Physical, Mechanical and Thermal Properties of an Epoxy Composite Reinforced With Nauclea diderrichii (Bilinga) Wood Particles
Developing new materials by recovering waste materials in the polymer reinforcement process helps to protect the environment and ensure a circular economy for these waste materials when they reach the end of their life cycle. This study shows the possibility of developing a new composite with bilinga and epoxy resin waste. Composites were realised by using cold pressure moulding technique with different pressures, particle sizes and reinforcement rate. Physical tests were carrying out to determine moisture content, water absorption rate and density by using a gravimetric method. Three‐point bending tests were used to determine flexural Young modulus and maximum break stress. Asymmetric Hot plane method with insulated rear face were used to determine thermal conductivity of composites. Results obtained show that moisture content varies from 2.3% to 6.65% and water absorption rate from 61% to 191%. These results allow us to say that this composite material has a hydrophilicity character. Young’s modulus of these materials is between 117 and 1951 MPa. Breaking stress of these composite materials is between 0.5 and 12.5 MPa. Results show that increasing compaction pressure also increases the mechanical properties of composite, as shown by standard EN312 for used in dry and humid environments. The thermal conductivity of the composite in between 0.18 and 0.27 W m −1 K −1 . These results confirm that the composite materials produced can be used in furniture manufacturing, thermal insulation for homes and ceilings, and the development of sandwich materials.
- 17 January 2026
- Published by Wiley in Advances in Polymer Technology
- Vol. 2026 (1)
Open AccessPhysical, Mechanical and Thermal Properties of an Epoxy Composite Reinforced With Nauclea diderrichii (Bilinga) Wood Particles
Developing new materials by recovering waste materials in the polymer reinforcement process helps to protect the environment and ensure a circular economy for these waste materials when they reach the end of their life cycle. This study shows the possibility of developing a new composite with bilinga and epoxy resin waste. Composites were realised by using cold pressure moulding technique with different pressures, particle sizes and reinforcement rate. Physical tests were carrying out to determine moisture content, water absorption rate and density by using a gravimetric method. Three‐point bending tests were used to determine flexural Young modulus and maximum break stress. Asymmetric Hot plane method with insulated rear face were used to determine thermal conductivity of composites. Results obtained show that moisture content varies from 2.3% to 6.65% and water absorption rate from 61% to 191%. These results allow us to say that this composite material has a hydrophilicity character. Young’s modulus of these materials is between 117 and 1951 MPa. Breaking stress of these composite materials is between 0.5 and 12.5 MPa. Results show that increasing compaction pressure also increases the mechanical properties of composite, as shown by standard EN312 for used in dry and humid environments. The thermal conductivity of the composite in between 0.18 and 0.27 W m −1 K −1 . These results confirm that the composite materials produced can be used in furniture manufacturing, thermal insulation for homes and ceilings, and the development of sandwich materials.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1)
Effect of NaOH Concentration and Curing Temperature on Geopolymers Incorporating Oyster Shell and Glass Waste
This study investigates the influence of NaOH concentration, curing temperature, oyster shell powder (PC) and glass powder (PV) on the physical and mechanical properties of geopolymer cements based on calcined clay, aiming to enhance the performance of construction materials in Douala. Oyster shells and glass waste, rich in calcite and silica, respectively, are underutilized and contribute to environmental pollution in Cameroon. Geopolymers, a sustainable alternative to traditional Portland cement, were formulated by partially replacing metakaolin with PC and PV powders. The study focuses on key parameters such as density, water absorption, porosity, and compressive strength, evaluated at different curing temperatures (40°C–60°C) and NaOH concentrations (8 and 12 M). The results showed that the optimal formulation, obtained with 8 M NaOH and cured at 49°C, achieved a compressive strength of 3.29 MPa at 28 days, with an apparent density of 1.36, water absorption of 24.23%, and total porosity of 31.04%. The experimental design followed a full factorial 2 4 approach with a center point in order to evaluate the combined effects of NaOH concentration and curing temperature, and to establish predictive models for each property. Statistical analysis using ANOVA was used to evaluate the main effects and interactions of the factors studied, whereas optimization was performed using desirability functions to find the right balance between maximizing compressive strength and density, and minimizing porosity and water absorption. Although the maximum compressive strength achieved (6.44 MPa) is markedly lower than that of conventional geopolymers, which typically exceed 20 MPa, this material is particularly suitable for nonstructural applications such as lightweight masonry blocks or insulating panels. Future studies will focus on chemical and thermal characterizations, as well as on evaluating the flexural strength and long‐term durability of the material under tropical climatic conditions.
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1)
Open AccessEffect of NaOH Concentration and Curing Temperature on Geopolymers Incorporating Oyster Shell and Glass Waste
This study investigates the influence of NaOH concentration, curing temperature, oyster shell powder (PC) and glass powder (PV) on the physical and mechanical properties of geopolymer cements based on calcined clay, aiming to enhance the performance of construction materials in Douala. Oyster shells and glass waste, rich in calcite and silica, respectively, are underutilized and contribute to environmental pollution in Cameroon. Geopolymers, a sustainable alternative to traditional Portland cement, were formulated by partially replacing metakaolin with PC and PV powders. The study focuses on key parameters such as density, water absorption, porosity, and compressive strength, evaluated at different curing temperatures (40°C–60°C) and NaOH concentrations (8 and 12 M). The results showed that the optimal formulation, obtained with 8 M NaOH and cured at 49°C, achieved a compressive strength of 3.29 MPa at 28 days, with an apparent density of 1.36, water absorption of 24.23%, and total porosity of 31.04%. The experimental design followed a full factorial 2 4 approach with a center point in order to evaluate the combined effects of NaOH concentration and curing temperature, and to establish predictive models for each property. Statistical analysis using ANOVA was used to evaluate the main effects and interactions of the factors studied, whereas optimization was performed using desirability functions to find the right balance between maximizing compressive strength and density, and minimizing porosity and water absorption. Although the maximum compressive strength achieved (6.44 MPa) is markedly lower than that of conventional geopolymers, which typically exceed 20 MPa, this material is particularly suitable for nonstructural applications such as lightweight masonry blocks or insulating panels. Future studies will focus on chemical and thermal characterizations, as well as on evaluating the flexural strength and long‐term durability of the material under tropical climatic conditions.
- Open Access
- 1 January 2025
- Published by Wiley in International Journal of Polymer Science
- Vol. 2025 (1)
Physical, Chemical and Mechanical Performance of a Material From By‐Products of Cameroonian Origin: The Case of Luffa cylindrica Particles and Natural Latex From Hevea brasiliensis
This research focused on biomass resources used in Cameroon ( Luffa cylindrica (LC) sponges) as reinforcement and natural latex from Hevea brasiliensis as a matrix for the development of composites for industrial use. The LC is separated manually from the other parts of the fruit. The LC sponge is crushed and sieved to obtain different sizes ([ t < 0.35], [0.3–0.63], [ t ≥ 0.63]). The composites are cold moulded and then heated for 30 min at 105°C to polymerise. Five reinforcement rates (50%, 55%, 60%, 65% and 70%) by mass of LC particles are used. FTIR (Fourier transform infrared spectroscopy) analysis shows that the washed and unwashed particles are identical. The density 311–782 kg m −3 reveals that the material is lightweight with ρ < 450 and medium for 450 ≤ ρ ≤ 800 and that it would be useful in furniture and insulation. The moisture content 9.57%–13.94%, water absorption degree 88.53%–255.52% and thickness swelling degree 13.23%–70.8% demonstrate the hydrophilic nature of the composites produced. Mechanical tests show that Young’s modulus 0.37–131.48 MPa and tensile strength 0.008–1.373 MPa decrease with increasing size and reinforcement content, while elongation at break 0.58%–10.61% increases. MANOVA (multivariate analysis of variance) confirms the statistically significant effects of size and reinforcement content on mechanical properties. These results confirm the potential of these biocomposites for use in furniture, thermal insulation and automotive applications.
- 1 January 2025
- Published by Wiley in International Journal of Polymer Science
- Vol. 2025 (1)
Open AccessPhysical, Chemical and Mechanical Performance of a Material From By‐Products of Cameroonian Origin: The Case of Luffa cylindrica Particles and Natural Latex From Hevea brasiliensis
This research focused on biomass resources used in Cameroon ( Luffa cylindrica (LC) sponges) as reinforcement and natural latex from Hevea brasiliensis as a matrix for the development of composites for industrial use. The LC is separated manually from the other parts of the fruit. The LC sponge is crushed and sieved to obtain different sizes ([ t < 0.35], [0.3–0.63], [ t ≥ 0.63]). The composites are cold moulded and then heated for 30 min at 105°C to polymerise. Five reinforcement rates (50%, 55%, 60%, 65% and 70%) by mass of LC particles are used. FTIR (Fourier transform infrared spectroscopy) analysis shows that the washed and unwashed particles are identical. The density 311–782 kg m −3 reveals that the material is lightweight with ρ < 450 and medium for 450 ≤ ρ ≤ 800 and that it would be useful in furniture and insulation. The moisture content 9.57%–13.94%, water absorption degree 88.53%–255.52% and thickness swelling degree 13.23%–70.8% demonstrate the hydrophilic nature of the composites produced. Mechanical tests show that Young’s modulus 0.37–131.48 MPa and tensile strength 0.008–1.373 MPa decrease with increasing size and reinforcement content, while elongation at break 0.58%–10.61% increases. MANOVA (multivariate analysis of variance) confirms the statistically significant effects of size and reinforcement content on mechanical properties. These results confirm the potential of these biocomposites for use in furniture, thermal insulation and automotive applications.
- Open Access
- 23 April 2024
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2024, 1-14
Effect of Reinforcement Ratio and Particle Size on the Physical and Mechanical Performance of Epoxy Matrix Panels and Waste Wood from Iroko Chlorophora excelsa from Cameroon
The use of local materials developed from natural reinforcements remains a major challenge for many researchers in the development of the industry and the fight against pollution. The wood industry generates large quantities of environmental waste, including Iroko wood. To give Iroko a second life, this study uses Iroko sawdust waste to make an epoxy matrix composite material. The composite was produced using a cold pressing technique based on moving the top and bottom plates to a thickness of 10mm. On this basis, three particle sizes [tR)/matrix (M) percentages of 50R/50M, 60R/40M, and 70R/30M, where R is the reinforcement percentage and M is the matrix percentage. The physical tests, apparent and real density, porosity, moisture content, water absorption rate, absorption and desorption kinetics, diffusion theory, and activation energy were determined by the gravimetric method. A three-point bending test was carried out in accordance with the ASTM D790 for mechanical tests. The results show that the addition of Iroko particles lightens the material by reducing its density. The hydrophilic nature of Iroko particles increases the absorption rate and porosity, with good diffusion capacity as the particle size and percentage increase. The material produced can be light and porous, with possible applications in thermal insulation. In terms of kinetics, Verma et al.s model best correlates the experimental desorption points for the 3 isotherms, while Pages model best correlates the water absorption points. The mechanical results show that Youngs modulus and stress at break decrease with an increase in the reinforcement percentage and particle size. The mechanical results can be used to define the materials applications in construction and furniture. In accordance with the EN312 standard, the composites produced can be classified as type 2 lightweight materials, suitable for use in dry and damp areas.
- 23 April 2024
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2024, 1-14
Open AccessEffect of Reinforcement Ratio and Particle Size on the Physical and Mechanical Performance of Epoxy Matrix Panels and Waste Wood from Iroko Chlorophora excelsa from Cameroon
The use of local materials developed from natural reinforcements remains a major challenge for many researchers in the development of the industry and the fight against pollution. The wood industry generates large quantities of environmental waste, including Iroko wood. To give Iroko a second life, this study uses Iroko sawdust waste to make an epoxy matrix composite material. The composite was produced using a cold pressing technique based on moving the top and bottom plates to a thickness of 10mm. On this basis, three particle sizes [tR)/matrix (M) percentages of 50R/50M, 60R/40M, and 70R/30M, where R is the reinforcement percentage and M is the matrix percentage. The physical tests, apparent and real density, porosity, moisture content, water absorption rate, absorption and desorption kinetics, diffusion theory, and activation energy were determined by the gravimetric method. A three-point bending test was carried out in accordance with the ASTM D790 for mechanical tests. The results show that the addition of Iroko particles lightens the material by reducing its density. The hydrophilic nature of Iroko particles increases the absorption rate and porosity, with good diffusion capacity as the particle size and percentage increase. The material produced can be light and porous, with possible applications in thermal insulation. In terms of kinetics, Verma et al.s model best correlates the experimental desorption points for the 3 isotherms, while Pages model best correlates the water absorption points. The mechanical results show that Youngs modulus and stress at break decrease with an increase in the reinforcement percentage and particle size. The mechanical results can be used to define the materials applications in construction and furniture. In accordance with the EN312 standard, the composites produced can be classified as type 2 lightweight materials, suitable for use in dry and damp areas.
- Open Access
- 1 January 2024
- Published by Wiley in International Journal of Polymer Science
- Vol. 2024 (1)
Characterisation of Luffa cylindrica Fibre from Cameroon for Use in Composites: Effect of Alkaline Treatment
The study of Luffa cylindrica is seen as an alternative solution for the development of green materials. However, a lack of knowledge about some of their characteristics can slow down these applications. The present study focuses on the characterisation of the fibre derived from the Luffa cylindrica sponge. In this study, the fibre was extracted using a manual technique, followed by a treatment cycle with 5%, 7.5%, and 10% NaOH at a temperature of 28°C for 60 min. The results obtained show the lightness of the fibre through its low density (0.233‐0.419 g·cm-3), and a hydrophilic nature of the fibre is observed through its water absorption capacity (106.86‐180.53%), its relative humidity (9.86‐15.33%), and its capacity to diffuse water (2.03 × 10−14 m2·s-1 to 4.61 × 10−14 m2·s-1), which is close to that of other plant fibres, which means that it can be classified as porous, with possible applications in insulating and lightweight materials. Its diameter (418.61‐554.42 μm) and linear mass (34‐58 g·km-1) are high, in contrast to other fibres used in the textile industry to produce yarns. The mechanical results, namely, stress at break (9.744‐27.45 MPa), Young’s modulus (307.56‐582.41 MPa), and elongation at break (3.45%‐8.11%), are close to those of other plant fibres used as reinforcement in polymer matrix composites for applications in the automotive, insulation, furniture, and construction industries. Luffa cylindrica fibre could have applications in the same direction. Fibres treated with 5% NaOH effectively improve the properties of raw fibres.
- 1 January 2024
- Published by Wiley in International Journal of Polymer Science
- Vol. 2024 (1)
Open AccessCharacterisation of Luffa cylindrica Fibre from Cameroon for Use in Composites: Effect of Alkaline Treatment
The study of Luffa cylindrica is seen as an alternative solution for the development of green materials. However, a lack of knowledge about some of their characteristics can slow down these applications. The present study focuses on the characterisation of the fibre derived from the Luffa cylindrica sponge. In this study, the fibre was extracted using a manual technique, followed by a treatment cycle with 5%, 7.5%, and 10% NaOH at a temperature of 28°C for 60 min. The results obtained show the lightness of the fibre through its low density (0.233‐0.419 g·cm-3), and a hydrophilic nature of the fibre is observed through its water absorption capacity (106.86‐180.53%), its relative humidity (9.86‐15.33%), and its capacity to diffuse water (2.03 × 10−14 m2·s-1 to 4.61 × 10−14 m2·s-1), which is close to that of other plant fibres, which means that it can be classified as porous, with possible applications in insulating and lightweight materials. Its diameter (418.61‐554.42 μm) and linear mass (34‐58 g·km-1) are high, in contrast to other fibres used in the textile industry to produce yarns. The mechanical results, namely, stress at break (9.744‐27.45 MPa), Young’s modulus (307.56‐582.41 MPa), and elongation at break (3.45%‐8.11%), are close to those of other plant fibres used as reinforcement in polymer matrix composites for applications in the automotive, insulation, furniture, and construction industries. Luffa cylindrica fibre could have applications in the same direction. Fibres treated with 5% NaOH effectively improve the properties of raw fibres.