Ge-Ge Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ge-Ge Song has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bo Yu
State Key Laboratory of Low Carbon Catalysis and Carbon Dioxide Utilization, School of Petroleum Engineering, Yangtze University, Wuhan 430100, China
8 shared publications - Dongliang Sun
School of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617, China
8 shared publications Kong Ling
Key Laboratory of Thermo-Fluid Science and Engineering, Ministry of Education, School of Energy and Power Engineering, Xi'an Jiaotong University, Shaanxi 710049, China
8 shared publications- Wei Lu
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206, China
8 shared publications - Yu-Jie Chen
Key Laboratory of Thermo-Fluid Science and Engineering, Ministry of Education, School of Energy and Power Engineering, Xi'an Jiaotong University, Shaanxi 710049, China
8 shared publications Jinjia Wei
1 shared publication
Latest Publications
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.2
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.2
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.4
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.4
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.1
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.1
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.7
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.7
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.3
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.3
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.6
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.6
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.5
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 4 November 2022
- Published by AIP Publishing
- Vol. 34 (11) , 113314
10.1063/5.0115599.5
Under a low flow rate, gravity may become prominent for bubble behavior and heat transfer of flowing boiling because of the weakness of drag force from liquid, and its effect changes with the inclination angle of the mini-channel but without consensus. In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adopted to study the subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0°–180°) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg m−2 s−1. The inclination angle is found to have a slight effect on the flow boiling, which is different from the conclusion drawn based on the traditional-macro channel. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is proposed, which presses large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0°, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90°, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects fail as the inclination angle approaches 180°, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 22.5%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force. In addition, the effect of inclination angle on flow boiling becomes weaker with the increase in heat flux because of happening of slug flow.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11)
Numerical investigation of subcooled flow boiling in an inclined rectangular mini-channel at a low flow rate
In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adapted to study subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0-180{degree sign}) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg∙m-2∙s-1. The inclination angle is found to have a slight effect on the boiling of the flow. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is exerted on larger bubbles because of the reduction in liquid flow area in the downstream region of the mini-channel. This causes large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0{degree sign}, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90{degree sign}, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects begin to fail as the inclination angle approaches 180{degree sign}, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 20.1%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11)
Numerical investigation of subcooled flow boiling in an inclined rectangular mini-channel at a low flow rate
In this paper, based on a reasonable nucleus site density model and considering conjugate heat transfer, the coupled volume-of-fluid and level set method is adapted to study subcooled flow boiling in an inclined three-dimensional rectangular mini-channel (0-180{degree sign}) with a characteristic size of 1.0 mm at a low flow rate of 88.8 kg∙m-2∙s-1. The inclination angle is found to have a slight effect on the boiling of the flow. A bubbly flow appears when a heat flux of 300 kW/m2 is added. An unconventional impact force is exerted on larger bubbles because of the reduction in liquid flow area in the downstream region of the mini-channel. This causes large bubbles to slip along the heating wall, with slight differences in the flow pattern under different inclination angles. When the inclination angle is close to 0{degree sign}, the upstream small/medium bubbles leave the heating wall under gravitational effects, which is conducive to heat transfer. As the inclination angle approaches 90{degree sign}, gravity pushes the large bubbles downstream to leave the channel, favoring the rewetting of the dry patches below. These two positive effects begin to fail as the inclination angle approaches 180{degree sign}, leading to slightly worse overall heat exchange efficiency. However, the maximum differences in the average and local wall superheating of the mini-channel are only 8.4% and 20.1%, respectively, across the range of inclination angles because the flow pattern remains similar under the effect of the impact force.