Jun Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jun Yang has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- Kornelius Nielsch
Leibniz Institute for Solid State and Materials Research
6 shared publications - Jianhua Zhang
Shanghai University
5 shared publications - Xingwei Ding
Key Laboratory of Advanced Display and System Application, Ministry of Education, Shanghai University 1 , Shanghai
5 shared publications - Amin Bahrami
Leibniz Institute for Solid State and Materials Research Dresden
4 shared publications Kun Bai
School of microelectronics, Shanghai University, Shanghai, China
4 shared publicationsSebastian Lehmann
Leibniz Institute for Solid State and Materials Research, Dresden 01069, Germany
4 shared publications
Latest Publications
- 13 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (2)
Gallium precursor reaction pathway-driven low-temperature atomic layer deposition of IGZO for thin-film transistors
Indium gallium zinc oxide (IGZO) thin-film transistors (TFTs) fabricated by atomic layer deposition (ALD) are promising for large flat-panel display technology requiring low thermal budgets (<400 °C), which is critical for next-generation displays and back-end-of-line electronics. However, the choice of precursor affects the feasibility of low-temperature processes. In this study, two gallium precursors—triethylgallium (TEGa) and trimethylgallium—were employed to achieve low-temperature fabrication of IGZO TFTs by fully thermal ALD. A high field-effect mobility (μFE) of 40.09 cm2/V s was achieved at 250 °C for the IGZO TFTs fabricated by TEGa, which has a lower thermal budget than other methods. This performance is attributed to the unique β-hydride elimination pathway of TEGa, which not only enables low-temperature deposition but also significantly reduces the defect state density in the IGZO films. The TFT devices exhibited excellent stability under a 30-min positive bias stress test, with a threshold voltage shift (ΔVth) of merely 8 mV. These findings provide a new approach for the low-temperature deposition of metal oxide semiconductor devices.
- 13 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (2)
Gallium precursor reaction pathway-driven low-temperature atomic layer deposition of IGZO for thin-film transistors
Indium gallium zinc oxide (IGZO) thin-film transistors (TFTs) fabricated by atomic layer deposition (ALD) are promising for large flat-panel display technology requiring low thermal budgets (<400 °C), which is critical for next-generation displays and back-end-of-line electronics. However, the choice of precursor affects the feasibility of low-temperature processes. In this study, two gallium precursors—triethylgallium (TEGa) and trimethylgallium—were employed to achieve low-temperature fabrication of IGZO TFTs by fully thermal ALD. A high field-effect mobility (μFE) of 40.09 cm2/V s was achieved at 250 °C for the IGZO TFTs fabricated by TEGa, which has a lower thermal budget than other methods. This performance is attributed to the unique β-hydride elimination pathway of TEGa, which not only enables low-temperature deposition but also significantly reduces the defect state density in the IGZO films. The TFT devices exhibited excellent stability under a 30-min positive bias stress test, with a threshold voltage shift (ΔVth) of merely 8 mV. These findings provide a new approach for the low-temperature deposition of metal oxide semiconductor devices.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 1968-1974
Impact of Multidimensional Process Vectors in Enhancing Electrical Performance and Reliability of SnO TFT
As an emerging p-type semiconductor, the precise control of process parameters in tin monoxide (SnO) thin-film transistor (TFT) is crucial for their integration into complementary circuits. However, the metastability of Sn ${}^{{2}+}$ ions promotes excessive oxidation to Sn ${}^{{4}+}$ and degrades film morphology, impairing electrical characteristics. This study systematically explores the impact of multidimensional process vectors in enhancing the performance and stability of SnO TFT. By integrating a high- $k$ HfO2 gate dielectric, the gate capacitance per unit area was increased, effectively reducing the threshold voltage. Optimal device performance was achieved at a sputtering power of 50 W and a substrate temperature of $200~^{\circ } $ C, exhibiting a field-effect mobility of 2.10 cm2/V $\cdot $ s, an ${}_{\mathrm {ON- {OFF}}}$ current ratio of $1.13\times 10^{{4}}$ , a threshold voltage of −0.39 V, and a subthreshold swing (SS) of 0.97 V/dec. Material characterization confirmed a dominant Sn ${}^{{2}+}$ phase with minor Sn0 content, alongside a continuous, filmed morphology with low surface roughness, collectively contributing to enhanced carrier transport. Moreover, the device demonstrated excellent reliability under negative bias stress (NBS), with a threshold voltage shift of only −0.48 V, attributed to low bulk and interface trap state densities.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 1968-1974
Impact of Multidimensional Process Vectors in Enhancing Electrical Performance and Reliability of SnO TFT
As an emerging p-type semiconductor, the precise control of process parameters in tin monoxide (SnO) thin-film transistor (TFT) is crucial for their integration into complementary circuits. However, the metastability of Sn ${}^{{2}+}$ ions promotes excessive oxidation to Sn ${}^{{4}+}$ and degrades film morphology, impairing electrical characteristics. This study systematically explores the impact of multidimensional process vectors in enhancing the performance and stability of SnO TFT. By integrating a high- $k$ HfO2 gate dielectric, the gate capacitance per unit area was increased, effectively reducing the threshold voltage. Optimal device performance was achieved at a sputtering power of 50 W and a substrate temperature of $200~^{\circ } $ C, exhibiting a field-effect mobility of 2.10 cm2/V $\cdot $ s, an ${}_{\mathrm {ON- {OFF}}}$ current ratio of $1.13\times 10^{{4}}$ , a threshold voltage of −0.39 V, and a subthreshold swing (SS) of 0.97 V/dec. Material characterization confirmed a dominant Sn ${}^{{2}+}$ phase with minor Sn0 content, alongside a continuous, filmed morphology with low surface roughness, collectively contributing to enhanced carrier transport. Moreover, the device demonstrated excellent reliability under negative bias stress (NBS), with a threshold voltage shift of only −0.48 V, attributed to low bulk and interface trap state densities.
- 25 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (8)
ALD-derived high-k ZrAlOx dielectrics for boosted performance of CNTs/ZTO CMOS inverter
In this study, high-k dielectric zirconium aluminum oxide (ZrAlOx) and zirconium oxide (ZrO2) have been fabricated via atomic layer deposition. The effects of Al doping on the capacitance characteristics, leakage performance, surface roughness, and chemical composition of the ZrO2 and ZrAlOx gate insulators are investigated. ZnSnO thin-film transistors (ZTO TFTs) and carbon nanotube (CNT) TFTs have been integrated into the high-k dielectrics. By combining CNT TFTs with ZTO TFTs, complementary metal–oxide–semiconductor (CMOS) inverters have been developed, and the role of Al doping in enhancing the electrical characteristics of both TFTs and CMOS inverters has been investigated. The results show that, compared to CMOS inverters with ZrO2 gate insulators, those with ZrAlOx allow carriers to transport more smoothly at the interface and reduce carrier scattering, demonstrating a better performance with a smaller hysteresis (0.21 V), lower power consumption (5.0 × 10−8 W), higher gain (43.8), and better voltage transfer characteristics. This research provides theoretical support and practical value for the development of next-generation integrated circuits.
- 25 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (8)
ALD-derived high-k ZrAlOx dielectrics for boosted performance of CNTs/ZTO CMOS inverter
In this study, high-k dielectric zirconium aluminum oxide (ZrAlOx) and zirconium oxide (ZrO2) have been fabricated via atomic layer deposition. The effects of Al doping on the capacitance characteristics, leakage performance, surface roughness, and chemical composition of the ZrO2 and ZrAlOx gate insulators are investigated. ZnSnO thin-film transistors (ZTO TFTs) and carbon nanotube (CNT) TFTs have been integrated into the high-k dielectrics. By combining CNT TFTs with ZTO TFTs, complementary metal–oxide–semiconductor (CMOS) inverters have been developed, and the role of Al doping in enhancing the electrical characteristics of both TFTs and CMOS inverters has been investigated. The results show that, compared to CMOS inverters with ZrO2 gate insulators, those with ZrAlOx allow carriers to transport more smoothly at the interface and reduce carrier scattering, demonstrating a better performance with a smaller hysteresis (0.21 V), lower power consumption (5.0 × 10−8 W), higher gain (43.8), and better voltage transfer characteristics. This research provides theoretical support and practical value for the development of next-generation integrated circuits.
- 13 August 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (35)
High-Performance Two-Dimensional Electron Gas IGZO Thin-Film Transistors Realized by RF Sputtering and Atomic Layer Deposition
Amorphous oxide semiconductor thin-film transistors (TFTs) find wide application in display technologies, yet balancing high mobility with temperature stability poses significant challenges. To solve this problem, this work proposes a bilayer indium gallium zinc oxide (IGZO) TFT with 10 nm IGZO deposited via the thermal atomic layer deposition (TH-ALD) as the front channel layer and 20 nm IGZO deposited via RF sputtering as the back channel layer. Compared to single-layer IGZO TFTs of the same thickness prepared via TH-ALD and RF sputtering, the bilayer IGZO TFTs achieve high mobility and high stability compatibility, including a field-effect mobility of 36.2 cm2/Vs, an Ion/Ioff of 109, a subthreshold swing of 82 mV/dec., and a positive bias temperature stress (PBTS) test of 1800 s duration, with a threshold voltage offset (ΔVth) is only 0.06 V. The performance improvement is mainly attributed to the energy band bending phenomenon at the interface of the heterostructure of the bilayer IGZO, leading to the accumulation of carriers to form a Two-Dimensional Electron Gas (2DEG). This design concept provides an effective solution to the conflict between mobility and stability of ultra-high resolution displays.
- 13 August 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (35)
High-Performance Two-Dimensional Electron Gas IGZO Thin-Film Transistors Realized by RF Sputtering and Atomic Layer Deposition
Amorphous oxide semiconductor thin-film transistors (TFTs) find wide application in display technologies, yet balancing high mobility with temperature stability poses significant challenges. To solve this problem, this work proposes a bilayer indium gallium zinc oxide (IGZO) TFT with 10 nm IGZO deposited via the thermal atomic layer deposition (TH-ALD) as the front channel layer and 20 nm IGZO deposited via RF sputtering as the back channel layer. Compared to single-layer IGZO TFTs of the same thickness prepared via TH-ALD and RF sputtering, the bilayer IGZO TFTs achieve high mobility and high stability compatibility, including a field-effect mobility of 36.2 cm2/Vs, an Ion/Ioff of 109, a subthreshold swing of 82 mV/dec., and a positive bias temperature stress (PBTS) test of 1800 s duration, with a threshold voltage offset (ΔVth) is only 0.06 V. The performance improvement is mainly attributed to the energy band bending phenomenon at the interface of the heterostructure of the bilayer IGZO, leading to the accumulation of carriers to form a Two-Dimensional Electron Gas (2DEG). This design concept provides an effective solution to the conflict between mobility and stability of ultra-high resolution displays.
- Open Access
- 5 June 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (23) , 21891-21903
Printed Conformal and Transparent Magnetoresistive Sensors for Seamless Integration and Environment-Resilient Touchless Interaction
Combination of conformability and transparency is crucial for realizing the full capabilities of printed magnetoresistive sensors in cutting-edge technologies designed to blend into their surroundings and applications. However, achieving this poses a critical challenge due to conflicting requirements: magnetic nanowires optimized for deformability exhibit a tendency to cluster, thus compromising transparency. To balance this trade-off, we leverage magnetic fields to manipulate nanowires, simultaneously initiating alignment and pinning effects. These together ensure a uniform and anisotropic distribution across extensive areas, enhancing the sensor transparency (about 85%). Further, we harness the clustering tendency, repurposing it to create local entanglements that enhance mechanical durability against both bending (with a curvature radius of about 110 μm) and stretching (with 80% tensile strain) and result in stable performance during 10,000 magnetization cycles. With the anisotropic design, the printed sensors achieve high out-of-plane sensitivity, distinguishing them from traditional film-based counterparts with a predominant in-plane response. These sensors do not require physical contact during operation, fostering hygienic and safer interaction. Their robust performance under environmental interference (e.g., dust, liquid, and moisture) makes them versatile for real-world use. The above innovations position our sensor as an important driver across numerous emerging applications, e.g., touchless interactive transparent displays and integrated multifunctional windows.
- 5 June 2025
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 19 (23) , 21891-21903
Open AccessPrinted Conformal and Transparent Magnetoresistive Sensors for Seamless Integration and Environment-Resilient Touchless Interaction
Combination of conformability and transparency is crucial for realizing the full capabilities of printed magnetoresistive sensors in cutting-edge technologies designed to blend into their surroundings and applications. However, achieving this poses a critical challenge due to conflicting requirements: magnetic nanowires optimized for deformability exhibit a tendency to cluster, thus compromising transparency. To balance this trade-off, we leverage magnetic fields to manipulate nanowires, simultaneously initiating alignment and pinning effects. These together ensure a uniform and anisotropic distribution across extensive areas, enhancing the sensor transparency (about 85%). Further, we harness the clustering tendency, repurposing it to create local entanglements that enhance mechanical durability against both bending (with a curvature radius of about 110 μm) and stretching (with 80% tensile strain) and result in stable performance during 10,000 magnetization cycles. With the anisotropic design, the printed sensors achieve high out-of-plane sensitivity, distinguishing them from traditional film-based counterparts with a predominant in-plane response. These sensors do not require physical contact during operation, fostering hygienic and safer interaction. Their robust performance under environmental interference (e.g., dust, liquid, and moisture) makes them versatile for real-world use. The above innovations position our sensor as an important driver across numerous emerging applications, e.g., touchless interactive transparent displays and integrated multifunctional windows.
- Open Access
- 14 February 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (4) , 1493-1501
Ambipolar Transport in Phosphorus-Implanted WS2 Monolayers
- 14 February 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (4) , 1493-1501
Open AccessAmbipolar Transport in Phosphorus-Implanted WS2 Monolayers
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 588-591
Approach to High-Performance Indium Gallium Zinc Oxide Transistors by Thermal Atomic Layer Deposition
Amorphous indium gallium zinc oxide (a-IGZO) thin films have been investigated to meet the high-resolution demands of augmented reality (AR) and virtual reality (VR) applications. In this study, we report on thin-film transistors (TFTs) derived from fully thermal atomic layer deposition (ALD), using IGZO as the channel layer and Al2O3 as the gate dielectric. By optimizing the deposition sequence and post-treatment processes, we achieved a high field-effect mobility of 52.5 cm2/Vs and a steep subthreshold swing of 116 mV/decade. This exceptional performance is attributed to the elevated In2O3 content in the IGZO thin films, which induces a substantial increase in sub-gap states adjacent to the conduction band minimum (CBM) and valence band maximum (VBM) while concurrently reducing the bandgap. At an elevated measurement temperature of 125 °C, the device exhibited an enhanced field-effect mobility of 60.4 cm2/Vs. These findings offer a new approach for optimizing metal oxide-based electronics.
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (4) , 588-591
Approach to High-Performance Indium Gallium Zinc Oxide Transistors by Thermal Atomic Layer Deposition
Amorphous indium gallium zinc oxide (a-IGZO) thin films have been investigated to meet the high-resolution demands of augmented reality (AR) and virtual reality (VR) applications. In this study, we report on thin-film transistors (TFTs) derived from fully thermal atomic layer deposition (ALD), using IGZO as the channel layer and Al2O3 as the gate dielectric. By optimizing the deposition sequence and post-treatment processes, we achieved a high field-effect mobility of 52.5 cm2/Vs and a steep subthreshold swing of 116 mV/decade. This exceptional performance is attributed to the elevated In2O3 content in the IGZO thin films, which induces a substantial increase in sub-gap states adjacent to the conduction band minimum (CBM) and valence band maximum (VBM) while concurrently reducing the bandgap. At an elevated measurement temperature of 125 °C, the device exhibited an enhanced field-effect mobility of 60.4 cm2/Vs. These findings offer a new approach for optimizing metal oxide-based electronics.
- Open Access
- 26 June 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (27) , 17500-17508
Interfacial Distortion of Sb2Te3–Sb2Se3 Multilayers via Atomic Layer Deposition for Enhanced Thermoelectric Properties
Atomic layer deposition (ALD) is an effective technique for depositing thin films with precise control of layer thickness and functional properties. In this work, Sb2Te3-Sb2Se3 nanostructures were synthesized using thermal ALD. A decrease in the Sb2Te3 layer thickness led to the emergence of distinct peaks from the Laue rings, indicative of a highly textured film structure with optimized crystallinity. Density functional theory simulations revealed that carrier redistribution occurs at the interface to establish charge equilibrium. By carefully optimizing the layer thicknesses, we achieved an obvious enhancement in the Seebeck coefficient, reaching a peak figure of merit (zT) value of 0.38 at room temperature. These investigations not only provide strong evidence for the potential of ALD manipulation to improve the electrical performance of metal chalcogenides but also offer valuable insights into achieving high performance in two-dimensional materials.
- 26 June 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (27) , 17500-17508
Open AccessInterfacial Distortion of Sb2Te3–Sb2Se3 Multilayers via Atomic Layer Deposition for Enhanced Thermoelectric Properties
Atomic layer deposition (ALD) is an effective technique for depositing thin films with precise control of layer thickness and functional properties. In this work, Sb2Te3-Sb2Se3 nanostructures were synthesized using thermal ALD. A decrease in the Sb2Te3 layer thickness led to the emergence of distinct peaks from the Laue rings, indicative of a highly textured film structure with optimized crystallinity. Density functional theory simulations revealed that carrier redistribution occurs at the interface to establish charge equilibrium. By carefully optimizing the layer thicknesses, we achieved an obvious enhancement in the Seebeck coefficient, reaching a peak figure of merit (zT) value of 0.38 at room temperature. These investigations not only provide strong evidence for the potential of ALD manipulation to improve the electrical performance of metal chalcogenides but also offer valuable insights into achieving high performance in two-dimensional materials.
- Open Access
SnS2 thin film with in-situ and controllable Sb doping via atomic layer deposition for optoelectronic applications
SnS2 stands out as a highly promising two-dimensional material with significant potential for applications in the field of electronics. Numerous attempts have been undertaken to modulate the physical properties of SnS2 by doping with various metal ions. Here, we deposited a series of Sb-doped SnS2 via atomic layer deposition (ALD) super-cycle process and compared its crystallinity, composition, and optical properties to those of pristine SnS2. We found that the increase in the concentration of Sb is accompanied by a gradual reduction in the Sn and S binding energies. The work function is increased upon Sb doping from 4.32 eV (SnS2) to 4.75 eV (Sb-doped SnS2 with 9:1 ratio). When integrated into photodetectors, the Sb-doped SnS2 showed improved performances, demonstrating increased peak photoresponsivity values from 19.5 A/W to 27.8 A/W at 405 nm, accompanied by an improvement in response speed. These results offer valuable insights into next-generation optoelectronic applications based on SnS2.
Open AccessSnS2 thin film with in-situ and controllable Sb doping via atomic layer deposition for optoelectronic applications
SnS2 stands out as a highly promising two-dimensional material with significant potential for applications in the field of electronics. Numerous attempts have been undertaken to modulate the physical properties of SnS2 by doping with various metal ions. Here, we deposited a series of Sb-doped SnS2 via atomic layer deposition (ALD) super-cycle process and compared its crystallinity, composition, and optical properties to those of pristine SnS2. We found that the increase in the concentration of Sb is accompanied by a gradual reduction in the Sn and S binding energies. The work function is increased upon Sb doping from 4.32 eV (SnS2) to 4.75 eV (Sb-doped SnS2 with 9:1 ratio). When integrated into photodetectors, the Sb-doped SnS2 showed improved performances, demonstrating increased peak photoresponsivity values from 19.5 A/W to 27.8 A/W at 405 nm, accompanied by an improvement in response speed. These results offer valuable insights into next-generation optoelectronic applications based on SnS2.