Akmaral Kinzhibekova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Akmaral Kinzhibekova has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Evgeniy Prikhodko
Department of Heat Power Engineering, Toraighyrov University, 64 Lomov Str., Pavlodar 140000, Kazakhstan
8 shared publications - Nazgul Aripova
Department of Heat Power Engineering, Toraighyrov University, 64 Lomov Str., Pavlodar 140000, Kazakhstan
7 shared publications - Alexandr Nikiforov
Department of Heat Power Engineering, Toraighyrov University, 64 Lomov Str., Pavlodar 140000, Kazakhstan
6 shared publications - Amangeldy Karmanov
Department of Heat Power Engineering, Toraighyrov University, 64 Lomov Str., Pavlodar 140000, Kazakhstan
6 shared publications - Amangeldy Karmanov
Toraighyrov University
5 shared publications - Aleksandr Nikiforov
Toraighyrov University, Faculty of Energy, Department of Heat Power Engineering, Pavlodar, Republic of Kazakhstan
4 shared publications
Latest Publications
- Open Access
- 11 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 6976
Modeling and Experimental Evaluation of Fixed-Bed Convective Drying of Composite Peat-Coal Fuel Pellets
Drying of fragile granules of bulk materials has to be carried out in a fixed bed to prevent particle damage. This way of drying protects the granules, but the lack of mixing of the particles leads to an uneven distribution of heat and mass transfer conditions in the bed. It is necessary to be able to predict the distribution of drying conditions inside the bed to select a rational drying mode. In this paper, a mathematical model for drying bulk media in a fixed bed is proposed, its parametric identification is carried out, and the model is verified by comparison with experimental results. The numerical model is based on explicit difference schemes using the mathematical apparatus of Markov chains. The experimental study was carried out on a laboratory dryer with the detection of local drying parameters according to the height of the fixed bed. The numerical and experimental results were obtained at the fixed temperature (90 °C) and gas velocity (0.5 m∙s−1). It has been shown that at a certain bed height, areas with relative gas humidity above 100% are formed within it, which negatively affects the efficiency of the drying. The proposed model allows identifying the indicated ineffective drying modes, and has proven to be a reliable tool for predicting the moisture ratio of the material with an MAPE of less than 7%.
- 11 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 6976
Open AccessModeling and Experimental Evaluation of Fixed-Bed Convective Drying of Composite Peat-Coal Fuel Pellets
Drying of fragile granules of bulk materials has to be carried out in a fixed bed to prevent particle damage. This way of drying protects the granules, but the lack of mixing of the particles leads to an uneven distribution of heat and mass transfer conditions in the bed. It is necessary to be able to predict the distribution of drying conditions inside the bed to select a rational drying mode. In this paper, a mathematical model for drying bulk media in a fixed bed is proposed, its parametric identification is carried out, and the model is verified by comparison with experimental results. The numerical model is based on explicit difference schemes using the mathematical apparatus of Markov chains. The experimental study was carried out on a laboratory dryer with the detection of local drying parameters according to the height of the fixed bed. The numerical and experimental results were obtained at the fixed temperature (90 °C) and gas velocity (0.5 m∙s−1). It has been shown that at a certain bed height, areas with relative gas humidity above 100% are formed within it, which negatively affects the efficiency of the drying. The proposed model allows identifying the indicated ineffective drying modes, and has proven to be a reliable tool for predicting the moisture ratio of the material with an MAPE of less than 7%.
- 30 June 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 2, 2026,p. 312-326
АНАЛИЗ ТЕПЛОФИЗИЧЕСКИХ ХАРАКТЕРИСТИК ОРГАНИЧЕСКИХ ОТХОДОВ
В статье представлены результаты анализа теплофизических характеристик органических отходов с целью оценки возможности их энергетической утилизации. Актуальность исследования обусловлена устойчивым ростом объёмов органических отходов в Республике Казахстан и в мировой практике, а также необходимостью снижения экологической нагрузки за счёт вовлечения отходов в энергетический оборот. Особое внимание уделено техногенным органическим отходам угольной отрасли – угольным отвальным породам, образующимся при добыче, транспортировке и переработке угля. В работе рассмотрены ключевые теплофизические показатели органических отходов: влажность, зольность и низшая теплота сгорания, которые в наибольшей степени определяют эффективность их использования в качестве вторичного энергетического сырья. Экспериментальные данные получены на основе отчёта по определению теплофизических характеристик угольных отвальных пород с применением нормативных методов испытаний. Результаты исследований представлены в виде таблиц с последующим аналитическим обсуждением, что позволяет выявить закономерности изменения свойств отходов в зависимости от их происхождения. Проведённый анализ показал, что угольные отвальные породы характеризуются низкой влажностью, однако отличаются значительной вариацией зольности и теплоты сгорания. Установлено, что отдельные фракции угольных отвальных пород обладают достаточным энергетическим потенциалом и могут рассматриваться как перспективное вторичное топливо. Несмотря на то, что отходы растительной биомассы характеризуются повышенной влажностью и значительно различаются по зольности, энергетическое использование отходов растительной биомассы целесообразно, что обусловлено достаточной теплотой при экологических преимуществах. Полученные результаты подтверждают целесообразность комплексного подхода к утилизации органических отходов и могут быть использованы при разработке технологий их энергетического использования. Ключевые слова: органические отходы, угольные отвальные породы, теплофизические характеристики, влажность, зольность, теплота сгорания.
- 30 June 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 2, 2026,p. 312-326
АНАЛИЗ ТЕПЛОФИЗИЧЕСКИХ ХАРАКТЕРИСТИК ОРГАНИЧЕСКИХ ОТХОДОВ
В статье представлены результаты анализа теплофизических характеристик органических отходов с целью оценки возможности их энергетической утилизации. Актуальность исследования обусловлена устойчивым ростом объёмов органических отходов в Республике Казахстан и в мировой практике, а также необходимостью снижения экологической нагрузки за счёт вовлечения отходов в энергетический оборот. Особое внимание уделено техногенным органическим отходам угольной отрасли – угольным отвальным породам, образующимся при добыче, транспортировке и переработке угля. В работе рассмотрены ключевые теплофизические показатели органических отходов: влажность, зольность и низшая теплота сгорания, которые в наибольшей степени определяют эффективность их использования в качестве вторичного энергетического сырья. Экспериментальные данные получены на основе отчёта по определению теплофизических характеристик угольных отвальных пород с применением нормативных методов испытаний. Результаты исследований представлены в виде таблиц с последующим аналитическим обсуждением, что позволяет выявить закономерности изменения свойств отходов в зависимости от их происхождения. Проведённый анализ показал, что угольные отвальные породы характеризуются низкой влажностью, однако отличаются значительной вариацией зольности и теплоты сгорания. Установлено, что отдельные фракции угольных отвальных пород обладают достаточным энергетическим потенциалом и могут рассматриваться как перспективное вторичное топливо. Несмотря на то, что отходы растительной биомассы характеризуются повышенной влажностью и значительно различаются по зольности, энергетическое использование отходов растительной биомассы целесообразно, что обусловлено достаточной теплотой при экологических преимуществах. Полученные результаты подтверждают целесообразность комплексного подхода к утилизации органических отходов и могут быть использованы при разработке технологий их энергетического использования. Ключевые слова: органические отходы, угольные отвальные породы, теплофизические характеристики, влажность, зольность, теплота сгорания.
- 31 March 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 1,2026,p. 263-272
АНАЛИЗ ИСПОЛЬЗОВАНИЯ ФЕРРОСПЛАВНОГО ГАЗА В КАЧЕСТВЕ ВТОРИЧНОГО ЭНЕРГОРЕСУРСА НА ПРЕДПРИЯТИИ
В статье рассматриваются пути повышения энергетической эффективности ферросплавного производства за счет использования теплового потенциала вторичных энергоресурсов (ВЭР). Проведен анализ образования и распределения ферросплавного газа, определена его роль как котельного топлива, рассчитан баланс тепловой энергии. Особое внимание уделено проблеме сжигания некондиционного ферросплавного газа на свечах, что приводит к потерям значительного объема потенциальной тепловой энергии и негативному воздействию на окружающую среду. В ходе исследования дана оценка достаточности ферросплавного газа для покрытия тепловых нагрузок при различных режимах работы предприятия и рассмотрены перспективы замещения внешних источников теплоснабжения за счет внутреннего энергетического потенциала. Дополнительно проанализированы существующие практики утилизации ВЭР, выявлены их ограничения и обозначены направления совершенствования технологий. Подчеркивается, что рациональное использование вторичных энергоресурсов способствует не только экономии топлива, но и сокращению выбросов парниковых газов, что особенно актуально в условиях ужесточения экологических требований. Полученные результаты подтверждают необходимость внедрения инновационных технических решений, ориентированных на комплексное использование ВЭР, что позволит существенно снизить топливно-энергетические затраты и повысить экологическую безопасность производства. Ключевые слова: ферросплавное производство, вторичные энергоресурсы, энергетическая эффективность, ферросплавный газ, тепловая энергия.
- 31 March 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 1,2026,p. 263-272
АНАЛИЗ ИСПОЛЬЗОВАНИЯ ФЕРРОСПЛАВНОГО ГАЗА В КАЧЕСТВЕ ВТОРИЧНОГО ЭНЕРГОРЕСУРСА НА ПРЕДПРИЯТИИ
В статье рассматриваются пути повышения энергетической эффективности ферросплавного производства за счет использования теплового потенциала вторичных энергоресурсов (ВЭР). Проведен анализ образования и распределения ферросплавного газа, определена его роль как котельного топлива, рассчитан баланс тепловой энергии. Особое внимание уделено проблеме сжигания некондиционного ферросплавного газа на свечах, что приводит к потерям значительного объема потенциальной тепловой энергии и негативному воздействию на окружающую среду. В ходе исследования дана оценка достаточности ферросплавного газа для покрытия тепловых нагрузок при различных режимах работы предприятия и рассмотрены перспективы замещения внешних источников теплоснабжения за счет внутреннего энергетического потенциала. Дополнительно проанализированы существующие практики утилизации ВЭР, выявлены их ограничения и обозначены направления совершенствования технологий. Подчеркивается, что рациональное использование вторичных энергоресурсов способствует не только экономии топлива, но и сокращению выбросов парниковых газов, что особенно актуально в условиях ужесточения экологических требований. Полученные результаты подтверждают необходимость внедрения инновационных технических решений, ориентированных на комплексное использование ВЭР, что позволит существенно снизить топливно-энергетические затраты и повысить экологическую безопасность производства. Ключевые слова: ферросплавное производство, вторичные энергоресурсы, энергетическая эффективность, ферросплавный газ, тепловая энергия.
- Open Access
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Journal of Applied Engineering Science
- Vol. 24 (1) , 107-116
Development of a device for cooling ladle liners for casting ladles
This article focuses on the controlled cooling process of the linings of ferroalloy production ladles. Analysis of the operating conditions of the linings revealed that temperature stresses during heating and cooling are the main cause of damage to the linings of high-temperature units. At the enterprise in question, the cooling process is uncontrolled when the lining is exposed to the workshop atmosphere. This leads to cracks forming in the lining and its subsequent destruction. Cooling schedules have been developed for the ladles under consideration, during which the resulting thermal stresses do not damage the lining. A device has been developed for the ladle liners to ensure the cooling process is kept on schedule. Incomplete liner replacement involves cooling the ladle by supplying a mixture of combustion gases from the ladle heating booth and air. The liner is cooled using a mixture of three media: ambient air from the workshop, combustion products from the ladle heating stand, and combustion products from the ferroalloy gas burnt in the burner. A cooling schedule for casting ladle liners has been developed to ensure that thermal stresses do not exceed the strength limit of the refractory materials. At the same time, the cooling time is reduced from 19 hours 30 minutes to 6 hours 50 minutes. The developed device enables the outer and inner walls of the lining to be cooled, secondary resources (ferroalloy gas and combustion products from the ladle heating stand) to be used.
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Journal of Applied Engineering Science
- Vol. 24 (1) , 107-116
Open AccessDevelopment of a device for cooling ladle liners for casting ladles
This article focuses on the controlled cooling process of the linings of ferroalloy production ladles. Analysis of the operating conditions of the linings revealed that temperature stresses during heating and cooling are the main cause of damage to the linings of high-temperature units. At the enterprise in question, the cooling process is uncontrolled when the lining is exposed to the workshop atmosphere. This leads to cracks forming in the lining and its subsequent destruction. Cooling schedules have been developed for the ladles under consideration, during which the resulting thermal stresses do not damage the lining. A device has been developed for the ladle liners to ensure the cooling process is kept on schedule. Incomplete liner replacement involves cooling the ladle by supplying a mixture of combustion gases from the ladle heating booth and air. The liner is cooled using a mixture of three media: ambient air from the workshop, combustion products from the ladle heating stand, and combustion products from the ferroalloy gas burnt in the burner. A cooling schedule for casting ladle liners has been developed to ensure that thermal stresses do not exceed the strength limit of the refractory materials. At the same time, the cooling time is reduced from 19 hours 30 minutes to 6 hours 50 minutes. The developed device enables the outer and inner walls of the lining to be cooled, secondary resources (ferroalloy gas and combustion products from the ladle heating stand) to be used.
- 28 March 2025
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 1.2025,p. 274-284
ВЛИЯНИЕ ЭКСПЛУАТАЦИОННЫХ ФАКТОРОВ НА ХАРАКТЕРИСТИКИ ОГНЕУПОРОВ ВЫСОКОТЕМПЕРАТУРНЫХ АГРЕГАТОВ
Энергетическая эффективность большинства металлургических агрегатов во многом определяется работой футеровок. Продолжительность рабочей кампании агрегата, затраты энергии при нестационарных тепловых режимах и другие показатели зависят от состояния футеровки. Проблема повышения энергетической эффективности работы высокотемпературных агрегатов должна решаться посредством рационализации режимов их тепловой работы, конструкции отдельных элементов и агрегатов в целом. Такие высокотемпературные агрегаты, как разливочные ковши работают с высокотемпературными рабочими средами − температура расплава металла, сливаемого с печи, составляет 1600-1650 оС. Повышение стойкости футеровок высокотемператуных агррегатов является актуальной задачей. Увеличение рабочей кампании агрегатов до ремонта позволяет экономить финансовые и трудовые ресурсы, а также увеличивать производительность. Стойкость футеровок во многом определяется рациональными условиями эксплуатации и соблюдением технологических режимов. В настоящее время вследствие проведения ряда технологических процессов (легирование, десульфурация, раскисление и др.) непосредственно в ковше, усложняется его эксплуатация. При этом к огнеупорам футеровки предъявляются более высокие требования как по качеству, так и по физико-химическим и термомехнаническим свойствам. В данной статье приведены результаты анализа процессов работы футеровки высокотемпературных агрегатов. Для этого были использованы методы литературного исследования. Ключевые слова: огнеупорные материалы, футеровка, высокотемпературный агрегат, разливочный ковш, графики разогрева и охлаждения.
- 28 March 2025
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Energetics series
- No. 1.2025,p. 274-284
ВЛИЯНИЕ ЭКСПЛУАТАЦИОННЫХ ФАКТОРОВ НА ХАРАКТЕРИСТИКИ ОГНЕУПОРОВ ВЫСОКОТЕМПЕРАТУРНЫХ АГРЕГАТОВ
Энергетическая эффективность большинства металлургических агрегатов во многом определяется работой футеровок. Продолжительность рабочей кампании агрегата, затраты энергии при нестационарных тепловых режимах и другие показатели зависят от состояния футеровки. Проблема повышения энергетической эффективности работы высокотемпературных агрегатов должна решаться посредством рационализации режимов их тепловой работы, конструкции отдельных элементов и агрегатов в целом. Такие высокотемпературные агрегаты, как разливочные ковши работают с высокотемпературными рабочими средами − температура расплава металла, сливаемого с печи, составляет 1600-1650 оС. Повышение стойкости футеровок высокотемператуных агррегатов является актуальной задачей. Увеличение рабочей кампании агрегатов до ремонта позволяет экономить финансовые и трудовые ресурсы, а также увеличивать производительность. Стойкость футеровок во многом определяется рациональными условиями эксплуатации и соблюдением технологических режимов. В настоящее время вследствие проведения ряда технологических процессов (легирование, десульфурация, раскисление и др.) непосредственно в ковше, усложняется его эксплуатация. При этом к огнеупорам футеровки предъявляются более высокие требования как по качеству, так и по физико-химическим и термомехнаническим свойствам. В данной статье приведены результаты анализа процессов работы футеровки высокотемпературных агрегатов. Для этого были использованы методы литературного исследования. Ключевые слова: огнеупорные материалы, футеровка, высокотемпературный агрегат, разливочный ковш, графики разогрева и охлаждения.
- Open Access
Development of Efficient Cooling Regimes for the Lining of a Ferroalloy Production Casting Ladle
The refractory lining of high-temperature aggregates determines the duration of their operation before major repairs. The ability to retain technological material within the aggregate’s working area is the main factor for its continued operation. The analysis shows that the main reason for the destruction of the lining of ferroalloy production casting ladles is the occurrence of thermal stresses in the processes of heating and cooling the lining. When the stresses exceed the ultimate strength of the refractory material used, the material is destroyed. The greater the magnitude and duration of the excess thermal stresses, the faster the lining destruction occurs. Streamlining thermal regimes is the most low-cost and sufficiently effective way to increase the durability of linings. The development of lining heating and cooling regimes can be carried out on the basis of determining the thermal stress state by calculating the maximum permissible heating rates. The developed regimes allow for working at speeds at which the resulting stresses do not exceed the ultimate strength of the refractory materials. The aim of this study is to develop efficient cooling regimes for the lining of a ferroalloy production casting ladle from the standpoint of the resulting thermal stresses. A method for determining the thermal stresses in the lining has been developed and implemented using Microsoft Excel. This facilitates the use of the developed methodology in production without the need for special skills on the part of operating personnel. Using the developed methodology, the cooling schedules for the lining of ferroalloy production ladles were improved. To reduce temperature unevenness across the lining cross-section, a decision was made to initially heat the outer surface of the lining and cool the inner surface of the lining. Heating the outer surface can be achieved by using the heat of combustion of the ferroalloy gas or the heat of the exhaust gases from the stand for drying and heating casting ladles. Cooling the inner surface of the lining can be achieved by natural convection. The result of the development and implementation of an efficient cooling regime is a reduction in thermal stresses to the required level throughout almost the entire cooling process.
Open AccessDevelopment of Efficient Cooling Regimes for the Lining of a Ferroalloy Production Casting Ladle
The refractory lining of high-temperature aggregates determines the duration of their operation before major repairs. The ability to retain technological material within the aggregate’s working area is the main factor for its continued operation. The analysis shows that the main reason for the destruction of the lining of ferroalloy production casting ladles is the occurrence of thermal stresses in the processes of heating and cooling the lining. When the stresses exceed the ultimate strength of the refractory material used, the material is destroyed. The greater the magnitude and duration of the excess thermal stresses, the faster the lining destruction occurs. Streamlining thermal regimes is the most low-cost and sufficiently effective way to increase the durability of linings. The development of lining heating and cooling regimes can be carried out on the basis of determining the thermal stress state by calculating the maximum permissible heating rates. The developed regimes allow for working at speeds at which the resulting stresses do not exceed the ultimate strength of the refractory materials. The aim of this study is to develop efficient cooling regimes for the lining of a ferroalloy production casting ladle from the standpoint of the resulting thermal stresses. A method for determining the thermal stresses in the lining has been developed and implemented using Microsoft Excel. This facilitates the use of the developed methodology in production without the need for special skills on the part of operating personnel. Using the developed methodology, the cooling schedules for the lining of ferroalloy production ladles were improved. To reduce temperature unevenness across the lining cross-section, a decision was made to initially heat the outer surface of the lining and cool the inner surface of the lining. Heating the outer surface can be achieved by using the heat of combustion of the ferroalloy gas or the heat of the exhaust gases from the stand for drying and heating casting ladles. Cooling the inner surface of the lining can be achieved by natural convection. The result of the development and implementation of an efficient cooling regime is a reduction in thermal stresses to the required level throughout almost the entire cooling process.
- Open Access
- 10 September 2024
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 125-135
Analysis of the thermal performance of the lining and the reasons for its destruction in petroleum coke calcination furnaces
This article discusses the thermal technological processes occurring in petroleum coke calcination furnaces, as well as issues of causes of destruction of the refractory material of the calcination furnace lining. The survey showed that the main factors influencing the duration of the work campaign of the lining are the temperature stresses that arise in the lining during sudden temperature changes during heating or cooling, as well as the chemical effect of the process material on the lining. It was revealed that in the inlet zone, where the drying of technological raw materials is carried out, the wear of the lining occurs evenly, and there is no significant damage. On thermal imaging images, this zone is displayed as uniform temperature fields on the outer surface of the furnace. In the calcination zone, the lining is characterized by the presence of main cracks that run along the seams. These cracks indicate the occurrence of significant thermal stresses when the furnace is heated. Work was done to determine the dependence of tensile strength on temperature, in the temperature range from 20 oC to 650 oC. Analysis of the results of determining the tensile strength showed a general tendency for it to increase with increasing temperature. This is explained by changes in the structure of the refractory material with increasing temperature and load. Taking into account the obtained dependence of the tensile strength on temperature allows one to adjust the heating schedules of the calcination furnace to reduce the temperature stress during the heating process
- 10 September 2024
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 125-135
Open AccessAnalysis of the thermal performance of the lining and the reasons for its destruction in petroleum coke calcination furnaces
This article discusses the thermal technological processes occurring in petroleum coke calcination furnaces, as well as issues of causes of destruction of the refractory material of the calcination furnace lining. The survey showed that the main factors influencing the duration of the work campaign of the lining are the temperature stresses that arise in the lining during sudden temperature changes during heating or cooling, as well as the chemical effect of the process material on the lining. It was revealed that in the inlet zone, where the drying of technological raw materials is carried out, the wear of the lining occurs evenly, and there is no significant damage. On thermal imaging images, this zone is displayed as uniform temperature fields on the outer surface of the furnace. In the calcination zone, the lining is characterized by the presence of main cracks that run along the seams. These cracks indicate the occurrence of significant thermal stresses when the furnace is heated. Work was done to determine the dependence of tensile strength on temperature, in the temperature range from 20 oC to 650 oC. Analysis of the results of determining the tensile strength showed a general tendency for it to increase with increasing temperature. This is explained by changes in the structure of the refractory material with increasing temperature and load. Taking into account the obtained dependence of the tensile strength on temperature allows one to adjust the heating schedules of the calcination furnace to reduce the temperature stress during the heating process
- Open Access
- 29 June 2024
- Published by Shakarim University in Bulletin of Shakarim University. Technical Sciences
- Vol. 1 (2(14)) , 341-347
TO THE ISSUE OF DETERMINING THE EFFICIENCY OF HEATING SYSTEMS
In order to maintain the temperature in a given mode in both residential and industrial premises it is necessary to establish the operation of a certain amount of equipment that will serve to receive, transfer and transmit the required amount of heat. The aggregate of such equipment is a heating system. From the correct choice of the device of such a system depends, as well as the efficiency of the devices, so the solution of energy-saving issues. Among multi-storey buildings, most of the buildings are connected to the centralized heat supply. The peculiarities of the thermal regime of buildings are taken into account at the design level, and heating systems must necessarily provide air parameters justified by regulations. A number of requirements are imposed on heating systems: sanitary-hygienic, economic, construction, installation and operational. Most often water is used as a heat carrier. The use of water heating has a number of advantages, including hygiene, reliability, quietness, simplicity and ease of operation. The materials from which radiators are made can be different: cast iron, steel, aluminum. It is also possible to use bimetallic radiators. The choice of a particular type of radiator is determined in each case, depending on the conditions. When calculating the heat transfer processes in the radiator, the heat transfer process from the hot water in the radiator to the heated air is calculated.
- 29 June 2024
- Published by Shakarim University in Bulletin of Shakarim University. Technical Sciences
- Vol. 1 (2(14)) , 341-347
Open AccessTO THE ISSUE OF DETERMINING THE EFFICIENCY OF HEATING SYSTEMS
In order to maintain the temperature in a given mode in both residential and industrial premises it is necessary to establish the operation of a certain amount of equipment that will serve to receive, transfer and transmit the required amount of heat. The aggregate of such equipment is a heating system. From the correct choice of the device of such a system depends, as well as the efficiency of the devices, so the solution of energy-saving issues. Among multi-storey buildings, most of the buildings are connected to the centralized heat supply. The peculiarities of the thermal regime of buildings are taken into account at the design level, and heating systems must necessarily provide air parameters justified by regulations. A number of requirements are imposed on heating systems: sanitary-hygienic, economic, construction, installation and operational. Most often water is used as a heat carrier. The use of water heating has a number of advantages, including hygiene, reliability, quietness, simplicity and ease of operation. The materials from which radiators are made can be different: cast iron, steel, aluminum. It is also possible to use bimetallic radiators. The choice of a particular type of radiator is determined in each case, depending on the conditions. When calculating the heat transfer processes in the radiator, the heat transfer process from the hot water in the radiator to the heated air is calculated.
- Open Access
Analysis of the Efficiency of Burning Briquettes from Agricultural and Industrial Residues in a Layer
The combustion of briquettes made from organic and industrial residues in small boilers requires researchers to consider the characteristics of this type of fuel and methods of its combustion. For the efficient combustion of fuel briquettes, a layered combustion method with the ability to regulate the supply of combustion air is better suited. The purpose of this research is to study the thermal technical conditions of briquetted fuel combustion. In order to carry this out, a stand was created, which made it possible to determine the combustion efficiency of this type of fuel. Two types of briquettes were studied: one with 30% sunflower husks and 70% leaves, and one with and 70% sunflower husks and 30% coke breeze. The combustion results of the briquettes show that heat loss from chemical under-burning was no more than 6.25%. To determine the temperature distribution in the fuel layer, a model of unsteady heat transfer in a fixed layer was used. A calculation of the temperature fields in the layer of burned fuel briquettes was carried out, which showed that the most favorable conditions for burning briquettes were created with a layer about 15–20 cm thick for both burned briquette options. The temperature was in the range of 450–750 °C, which on the one hand corresponds to experimental data and on the other hand provides a combustion regime that occurs with a relatively low loss to the environment. This installation and mathematical model will help future studies based on the processes of other types of organic waste combustion with a grate system.
Open AccessAnalysis of the Efficiency of Burning Briquettes from Agricultural and Industrial Residues in a Layer
The combustion of briquettes made from organic and industrial residues in small boilers requires researchers to consider the characteristics of this type of fuel and methods of its combustion. For the efficient combustion of fuel briquettes, a layered combustion method with the ability to regulate the supply of combustion air is better suited. The purpose of this research is to study the thermal technical conditions of briquetted fuel combustion. In order to carry this out, a stand was created, which made it possible to determine the combustion efficiency of this type of fuel. Two types of briquettes were studied: one with 30% sunflower husks and 70% leaves, and one with and 70% sunflower husks and 30% coke breeze. The combustion results of the briquettes show that heat loss from chemical under-burning was no more than 6.25%. To determine the temperature distribution in the fuel layer, a model of unsteady heat transfer in a fixed layer was used. A calculation of the temperature fields in the layer of burned fuel briquettes was carried out, which showed that the most favorable conditions for burning briquettes were created with a layer about 15–20 cm thick for both burned briquette options. The temperature was in the range of 450–750 °C, which on the one hand corresponds to experimental data and on the other hand provides a combustion regime that occurs with a relatively low loss to the environment. This installation and mathematical model will help future studies based on the processes of other types of organic waste combustion with a grate system.
- Open Access
Analysis of the Cooling Modes of the Lining of a Ferroalloy-Casting Ladle
An important element of the operation of high-temperature aggregates are modes that change over time. During these modes, maximum temperature changes are recorded in the cross-section of the lining of the aggregate. The difference in temperature leads to the formation of thermal stresses, which are the main reason for the repair of aggregates. During rapid heating, the inner layers of the lining are subjected to compressive stresses, while during rapid cooling, these layers experience tensile stresses. Under the same conditions, rapid cooling of the lining is more critical, since refractories have poor resistance to tension. The purpose of the study is to calculate and analyze the thermal stresses that arise during cooling of the casting ladle lining. The stresses are determined based on the calculation of the unsteady temperature field of the lining. Thermal stress values are necessary for analysis of the current cooling rates of casting ladles and subsequent development of optimal cooling modes for the lining. To solve the heat conductivity equation, a numerical method was chosen using an implicit four-point difference scheme. To study the cooling process of the casting ladle lining, temperature measurements were carried out in the zone of the greatest wear of the lining. Under conditions of natural convection, cooling of the casting ladle lining occurs unevenly. Cooling schedules during natural convection are characterized by significant unevenness and high rates of temperature decrease. The cooling rates of the inner surface of the lining at the initial stage of cooling significantly exceed the values recommended in the technical literature. Such cooling rates lead to the appearance of significant thermal stresses in the lining. For a refractory that has not been in service, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.27 times, and the tensile stresses exceed the corresponding limit values by 4.4 times. For refractories that have worked three fuses in the ladle lining, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.28 times, and the tensile stresses exceed the corresponding limit values by 3.19 times. The studied cooling modes for the casting ladle lining are unacceptable for operation. Cooling, taking into account the indicated rates, leads to the destruction of the lining material. To increase the resistance and duration of the working campaign of casting ladle linings, it is necessary to develop cooling modes for the lining at speeds at which the resulting thermal stresses do not exceed the strength of the refractory materials.
Open AccessAnalysis of the Cooling Modes of the Lining of a Ferroalloy-Casting Ladle
An important element of the operation of high-temperature aggregates are modes that change over time. During these modes, maximum temperature changes are recorded in the cross-section of the lining of the aggregate. The difference in temperature leads to the formation of thermal stresses, which are the main reason for the repair of aggregates. During rapid heating, the inner layers of the lining are subjected to compressive stresses, while during rapid cooling, these layers experience tensile stresses. Under the same conditions, rapid cooling of the lining is more critical, since refractories have poor resistance to tension. The purpose of the study is to calculate and analyze the thermal stresses that arise during cooling of the casting ladle lining. The stresses are determined based on the calculation of the unsteady temperature field of the lining. Thermal stress values are necessary for analysis of the current cooling rates of casting ladles and subsequent development of optimal cooling modes for the lining. To solve the heat conductivity equation, a numerical method was chosen using an implicit four-point difference scheme. To study the cooling process of the casting ladle lining, temperature measurements were carried out in the zone of the greatest wear of the lining. Under conditions of natural convection, cooling of the casting ladle lining occurs unevenly. Cooling schedules during natural convection are characterized by significant unevenness and high rates of temperature decrease. The cooling rates of the inner surface of the lining at the initial stage of cooling significantly exceed the values recommended in the technical literature. Such cooling rates lead to the appearance of significant thermal stresses in the lining. For a refractory that has not been in service, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.27 times, and the tensile stresses exceed the corresponding limit values by 4.4 times. For refractories that have worked three fuses in the ladle lining, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.28 times, and the tensile stresses exceed the corresponding limit values by 3.19 times. The studied cooling modes for the casting ladle lining are unacceptable for operation. Cooling, taking into account the indicated rates, leads to the destruction of the lining material. To increase the resistance and duration of the working campaign of casting ladle linings, it is necessary to develop cooling modes for the lining at speeds at which the resulting thermal stresses do not exceed the strength of the refractory materials.