Decong Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Decong Chen has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Yanzheng Bai
Huazhong University of Science and Technology
3 shared publications - Shaobo Qu
Huazhong University of Science and Technology
2 shared publications - Zebing Zhou
Huazhong University of Science and Technology
2 shared publications - Chaoli Ouyang
National Gravitation Laboratory, MOE Key Laboratory of Fundamental Physical Quantities Measurement, and School of Physics, Huazhong University of Science and Technology, Wuhan 430074, People’s Republic of China
1 shared publication - Chengrui Wang
National Gravitation Laboratory, MOE Key Laboratory of Fundamental Physical Quantities Measurement, and School of Physics, Huazhong University of Science and Technology, Wuhan 430074, People’s Republic of China
1 shared publication - Chengrui Wang
MOE Key Laboratory of Fundamental Physical Quantities Measurement, Hubei Key Laboratory of Gravitation and Quantum Physics, PGMF, School of Physics, Huazhong University of Science and Technology, Wuhan 430074, China
1 shared publication
Latest Publications
- 24 September 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (12) , 125117
Finite element analysis for the measurement error of electrostatic accelerometer due to the electrode misalignment
The electrostatic accelerometer is the key payload of many space missions, such as satellite gravity measurements, space gravitational experiments, with a typical precision requirement from nano-g to femto-g. The measurement error model analysis is an important issue for the electrostatic accelerometer with numerous error sources. The traditional method by theoretical analysis is complicated to evaluate the complete measurement error models quantitatively especially when the machining and assembly errors of the sensor head are considered. Limited by the earth gravity and seismic noise which is much higher than the intrinsic noise, the complete error model of electrostatic accelerometers can also hardly be tested on ground. In this paper, the method by using finite element analysis of the sensor head is studied. The simulation model for an electrostatic accelerometer sensor head is built, and the multi-conductor capacitance matrix data is simulated. The accuracy of the capacitance simulation is evaluated in three ways including the convergence check of the capacitance with the mesh size, the symmetry verification, and the sensitivity comparison with the theoretical model. Finally, the accelerometer measurement model is analyzed based on the simulation data, using the case of rotating installation misalignment of the upper electrode as an example. The measurement model and error items of one horizontal axis and one rotating axis are quantitatively evaluated. The method proposed in this paper provide a new effective approach to the measurement model analysis of the electrostatic accelerometers in complex working scenarios both in orbit and on ground, which could be helpful to enhance the performance and the efficiency of application.
- 24 September 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (12) , 125117
Finite element analysis for the measurement error of electrostatic accelerometer due to the electrode misalignment
The electrostatic accelerometer is the key payload of many space missions, such as satellite gravity measurements, space gravitational experiments, with a typical precision requirement from nano-g to femto-g. The measurement error model analysis is an important issue for the electrostatic accelerometer with numerous error sources. The traditional method by theoretical analysis is complicated to evaluate the complete measurement error models quantitatively especially when the machining and assembly errors of the sensor head are considered. Limited by the earth gravity and seismic noise which is much higher than the intrinsic noise, the complete error model of electrostatic accelerometers can also hardly be tested on ground. In this paper, the method by using finite element analysis of the sensor head is studied. The simulation model for an electrostatic accelerometer sensor head is built, and the multi-conductor capacitance matrix data is simulated. The accuracy of the capacitance simulation is evaluated in three ways including the convergence check of the capacitance with the mesh size, the symmetry verification, and the sensitivity comparison with the theoretical model. Finally, the accelerometer measurement model is analyzed based on the simulation data, using the case of rotating installation misalignment of the upper electrode as an example. The measurement model and error items of one horizontal axis and one rotating axis are quantitatively evaluated. The method proposed in this paper provide a new effective approach to the measurement model analysis of the electrostatic accelerometers in complex working scenarios both in orbit and on ground, which could be helpful to enhance the performance and the efficiency of application.
- Open Access
- 1 June 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (6)
A method for high-precision measuring differential transformer asymmetry
The differential transformer is an important component in the front-end electronics of high-precision capacitive position sensing circuits, which are widely employed in space inertial sensors and electrostatic accelerometers. The position sensing offset, one of the space inertial sensors’ most critical error sources in the performance range, is dominated by the differential transformer asymmetry and requires a high-precision evaluation. This paper proposes a method to assess differential transformers’ asymmetry and realize a prototype circuit to test a transformer sample. The results show that the asymmetry measurement precision can achieve 0.6 ppm for the transformer with an asymmetry level of about −278.2 ppm.
- 1 June 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (6)
Open AccessA method for high-precision measuring differential transformer asymmetry
The differential transformer is an important component in the front-end electronics of high-precision capacitive position sensing circuits, which are widely employed in space inertial sensors and electrostatic accelerometers. The position sensing offset, one of the space inertial sensors’ most critical error sources in the performance range, is dominated by the differential transformer asymmetry and requires a high-precision evaluation. This paper proposes a method to assess differential transformers’ asymmetry and realize a prototype circuit to test a transformer sample. The results show that the asymmetry measurement precision can achieve 0.6 ppm for the transformer with an asymmetry level of about −278.2 ppm.
- Open Access
Bias Stability Investigation of a Triaxial Navigation-Compatible Accelerometer with an Electrostatic Spring
The bias stability performance of accelerometers is essential for an inertial navigation system. The traditional pendulous accelerometer usually has a flexible connection structure, which could limit the long-term bias stability. Here, based on the main technologies employed in previous space missions of our group, we developed a terrestrial triaxial navigation-compatible accelerometer. Because there is no mechanical connection between the inertial test mass and the frame, the bias performance relies on the stability of the equivalent electrostatic spring, where further sources are analyzed to get the optimal electrostatic force scheme. To investigate the bias stability under different ranges, the vertical and horizontal measurement ranges are designed at 5 g and ±10 mg, respectively. A low-noise high-voltage levitation scheme is adopted to extend the vertical measurement range from sub-mg to more than earth’s 1-g gravity. Finally, the experimental validation results show that the 24-h bias stability of vertical and two horizontal directions come to 13.8 μg, 0.84 μg, and 0.77 μg, respectively.
Open AccessBias Stability Investigation of a Triaxial Navigation-Compatible Accelerometer with an Electrostatic Spring
The bias stability performance of accelerometers is essential for an inertial navigation system. The traditional pendulous accelerometer usually has a flexible connection structure, which could limit the long-term bias stability. Here, based on the main technologies employed in previous space missions of our group, we developed a terrestrial triaxial navigation-compatible accelerometer. Because there is no mechanical connection between the inertial test mass and the frame, the bias performance relies on the stability of the equivalent electrostatic spring, where further sources are analyzed to get the optimal electrostatic force scheme. To investigate the bias stability under different ranges, the vertical and horizontal measurement ranges are designed at 5 g and ±10 mg, respectively. A low-noise high-voltage levitation scheme is adopted to extend the vertical measurement range from sub-mg to more than earth’s 1-g gravity. Finally, the experimental validation results show that the 24-h bias stability of vertical and two horizontal directions come to 13.8 μg, 0.84 μg, and 0.77 μg, respectively.
- 1 November 2017
- Published by Elsevier in Materials Letters
- Vol. 207, 109-112
Synthesis of mesoporous Au-TiO2 nanocomposites via a one-pot sol-gel process with enhanced photocatalytic activity
- 1 November 2017
- Published by Elsevier in Materials Letters
- Vol. 207, 109-112
Synthesis of mesoporous Au-TiO2 nanocomposites via a one-pot sol-gel process with enhanced photocatalytic activity