Khajanajimudeen Mohamed Mydeen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Khajanajimudeen Mohamed Mydeen has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Balaji Krishnasamy
Sustainable Materials Research Lab, Department of Chemistry, PSG Institute of Technology and Applied Research, Coimbatore, India
3 shared publications - Muthukaruppan Alagar
Centre for Advanced Materials PSG College of Arts and Science Coimbatore India
3 shared publications - Hariharan Arumugam
Polymer Engineering Laboratory, PSG Institute of Technology and Applied Research, Coimbatore, India
2 shared publications Alagar Muthukaruppan
Polymer Engineering Laboratory, Department of Chemistry PSG Institute of Technology and Applied Research Coimbatore India
1 shared publicationArjitha Saravanamuthu
Polymer Engineering Laboratory, Department of Chemistry PSG Institute of Technology and Applied Research Coimbatore India
1 shared publication- Ellappan Satheeshkumar
Centre for Advanced Materials, PSG College of Arts and Science Coimbatore India
1 shared publication
Latest Publications
- 21 July 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (19) , 17737-17751
Zirconia Hybrid Oxides Reinforced Bio‐Based Benzoxazine/Epoxy Composites for Thermal, High Dielectric and Superhydrophobic Applications
The non‐sustainability of conventional benzoxazine and epoxy resins is highly concerning and the development of suitable bio‐alternative materials is very much warranted without compromising the end properties. Considering the preceding fact, the present study reports the synthesis of bio‐based tetrafunctional benzoxazine (T‐f) and epoxy (T‐e) blends to attain a highly thermally stable hybrid polymer system. Upon blending T‐e with T‐f, the curing temperature is reduced from 225°C to 175°C. Also, the prepared epoxy resin shows a curing temperature of 230°C. The blend shows excellent thermal stability with a char yield of 59%. Also, two ceramic‐based fillers were prepared and reinforced into the blend. The thermal stability of the composites was increased remarkably with a char yield up to 70%. Also, the dielectric constant of the composites was increased to 6.54 at 10 MHz. The ceramic composites show superhydrophobic behavior with a water contact angle reaching up to 161°.
- 21 July 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (19) , 17737-17751
Zirconia Hybrid Oxides Reinforced Bio‐Based Benzoxazine/Epoxy Composites for Thermal, High Dielectric and Superhydrophobic Applications
The non‐sustainability of conventional benzoxazine and epoxy resins is highly concerning and the development of suitable bio‐alternative materials is very much warranted without compromising the end properties. Considering the preceding fact, the present study reports the synthesis of bio‐based tetrafunctional benzoxazine (T‐f) and epoxy (T‐e) blends to attain a highly thermally stable hybrid polymer system. Upon blending T‐e with T‐f, the curing temperature is reduced from 225°C to 175°C. Also, the prepared epoxy resin shows a curing temperature of 230°C. The blend shows excellent thermal stability with a char yield of 59%. Also, two ceramic‐based fillers were prepared and reinforced into the blend. The thermal stability of the composites was increased remarkably with a char yield up to 70%. Also, the dielectric constant of the composites was increased to 6.54 at 10 MHz. The ceramic composites show superhydrophobic behavior with a water contact angle reaching up to 161°.
- 29 November 2024
- Published by Wiley in Polymer International
- Vol. 74 (4) , 353-370
Modified guaiacol‐based benzoxazines for optical, aggregation‐induced emission and corrosion‐resistant coating applications
Two new kinds of modified bifunctional and trifunctional guaiacol, namely 4,4′‐(bis(4‐fluorophenyl)methylene)bis(2‐methoxyphenol) (BBM) and 4,4′‐((2‐hydroxy‐4‐methoxyphenyl)(phenyl)methylene)bis(2‐methoxyphenol) (HBM), were synthesized using guaiacol with respective keto derivatives under appropriate experimental conditions. Two series of benzoxazines were developed with BBM and HBM using various amines (dodecylamine (dda), octadecylamine (oda), furfurylamine (ffa), aniline (a) and 4‐fluoroaniline (fa)) with paraformaldehyde through Mannich condensation with a view to utilize them for anticorrosive and optical resistant coating applications. The molecular structures of the synthesized precursors and benzoxazine monomers were characterized using appropriate analytical techniques. The polymerization temperature of the benzoxazines was assessed using differential scanning calorimetry. Among the benzoxazine monomers synthesized, the monomer HBM‐fa exhibits the lowest curing temperature (217 °C). Data obtained from thermogravimetric analysis indicated that the polybenzoxazines poly(BBM‐ffa) and poly(HBM‐ffa) possess higher thermal stability (455 and 425 °C) and higher char yield (54% and 60%) than the other polybenzoxazines. In both series, octadecylamine‐based polybenzoxazines (BBM‐oda and HBM‐oda) exhibited the highest values of water contact angle of 148° and 149° respectively. Additionally, the benzoxazines showed aggregation‐induced emission properties during fluorescence studies. Morphological analyses using different analytical techniques on selected polybenzoxazines were carried out before and after the corrosion process. Results from corrosion studies, i.e. Tafel and Nyquist plots, implied that the polybenzoxazines can be used as effective coating material to protect mild steels from corrosion. Data from different studies suggest that the developed benzoxazines can be used in the form of optical and anticorrosion coatings under thermally harsh and moist environments. © 2024 Society of Chemical Industry.
- 29 November 2024
- Published by Wiley in Polymer International
- Vol. 74 (4) , 353-370
Modified guaiacol‐based benzoxazines for optical, aggregation‐induced emission and corrosion‐resistant coating applications
Two new kinds of modified bifunctional and trifunctional guaiacol, namely 4,4′‐(bis(4‐fluorophenyl)methylene)bis(2‐methoxyphenol) (BBM) and 4,4′‐((2‐hydroxy‐4‐methoxyphenyl)(phenyl)methylene)bis(2‐methoxyphenol) (HBM), were synthesized using guaiacol with respective keto derivatives under appropriate experimental conditions. Two series of benzoxazines were developed with BBM and HBM using various amines (dodecylamine (dda), octadecylamine (oda), furfurylamine (ffa), aniline (a) and 4‐fluoroaniline (fa)) with paraformaldehyde through Mannich condensation with a view to utilize them for anticorrosive and optical resistant coating applications. The molecular structures of the synthesized precursors and benzoxazine monomers were characterized using appropriate analytical techniques. The polymerization temperature of the benzoxazines was assessed using differential scanning calorimetry. Among the benzoxazine monomers synthesized, the monomer HBM‐fa exhibits the lowest curing temperature (217 °C). Data obtained from thermogravimetric analysis indicated that the polybenzoxazines poly(BBM‐ffa) and poly(HBM‐ffa) possess higher thermal stability (455 and 425 °C) and higher char yield (54% and 60%) than the other polybenzoxazines. In both series, octadecylamine‐based polybenzoxazines (BBM‐oda and HBM‐oda) exhibited the highest values of water contact angle of 148° and 149° respectively. Additionally, the benzoxazines showed aggregation‐induced emission properties during fluorescence studies. Morphological analyses using different analytical techniques on selected polybenzoxazines were carried out before and after the corrosion process. Results from corrosion studies, i.e. Tafel and Nyquist plots, implied that the polybenzoxazines can be used as effective coating material to protect mild steels from corrosion. Data from different studies suggest that the developed benzoxazines can be used in the form of optical and anticorrosion coatings under thermally harsh and moist environments. © 2024 Society of Chemical Industry.
- 21 October 2022
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 34 (2) , 568-577
Industrial cutting waste granite dust reinforced cardanol benzoxazine/epoxy resin hybrid composites for high‐voltage electrical insulation applications
An attempt has been made to develop hybrid composites from benzoxazine monomer (C‐ddm) hybridized with DGEBA epoxy resin (EP) and reinforced with varying weight percentages (20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt%) of glycidoxypropyltrimethoxy‐ silane (GPTMS) functionalized granite dust (GD) obtained from industrial granite cutting and polishing process in order to utilize them for electrical insulation applications. The thermal stability of granite dust reinforced poly(EP‐co‐C‐ddm) composites was studied by TGA analysis. Among the composites samples studied, 100 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possess better thermal stability than that of other neat matrices and composites. Among the composites prepared using varying weight percentages of functionalized GD reinforcement, it was observed that 80 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possesses better hydrophobic character than that of other neat matrices and composites. The value of LOI calculated for neat matrix (poly[EP‐co‐C‐ddm]) and 20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt% GD reinforced composites was found to be 22, 28, 34, 40, 43 and 45 respectively. The 80 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possess the higher values of tensile strength and flexural strength of 47 MPa and 140 MPa, respectively than those of their samples. The values of electrical surface resistivity and electrical volume resistivity of all the neat matrices and GD reinforced polybenzoxazine composites were found to be in the order of 1012 and 1013 respectively. The values of dielectric strength obtained from break down voltage (BDV) for neat matrix [poly(EP‐co‐C‐ddm)] and 20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt% of GD reinforced poly(EP‐co‐C‐ddm) composites are 15.0, 15.5, 16.5, 17.0, 17.0 and 17.0 kV/mm, respectively. Data obtained from thermal stability, hydrophobic behavior and dielectric studies it was inferred that the hybrid polymer composites developed in the present work can be conveniently used in the form insulators, sealants, adhesives and matrices where application demands at high‐performance industrial and engineering applications.
- 21 October 2022
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 34 (2) , 568-577
Industrial cutting waste granite dust reinforced cardanol benzoxazine/epoxy resin hybrid composites for high‐voltage electrical insulation applications
An attempt has been made to develop hybrid composites from benzoxazine monomer (C‐ddm) hybridized with DGEBA epoxy resin (EP) and reinforced with varying weight percentages (20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt%) of glycidoxypropyltrimethoxy‐ silane (GPTMS) functionalized granite dust (GD) obtained from industrial granite cutting and polishing process in order to utilize them for electrical insulation applications. The thermal stability of granite dust reinforced poly(EP‐co‐C‐ddm) composites was studied by TGA analysis. Among the composites samples studied, 100 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possess better thermal stability than that of other neat matrices and composites. Among the composites prepared using varying weight percentages of functionalized GD reinforcement, it was observed that 80 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possesses better hydrophobic character than that of other neat matrices and composites. The value of LOI calculated for neat matrix (poly[EP‐co‐C‐ddm]) and 20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt% GD reinforced composites was found to be 22, 28, 34, 40, 43 and 45 respectively. The 80 wt% GD reinforced poly(EP‐co‐C‐ddm) composites possess the higher values of tensile strength and flexural strength of 47 MPa and 140 MPa, respectively than those of their samples. The values of electrical surface resistivity and electrical volume resistivity of all the neat matrices and GD reinforced polybenzoxazine composites were found to be in the order of 1012 and 1013 respectively. The values of dielectric strength obtained from break down voltage (BDV) for neat matrix [poly(EP‐co‐C‐ddm)] and 20 wt%, 40 wt%, 60 wt%, 80 wt% and 100 wt% of GD reinforced poly(EP‐co‐C‐ddm) composites are 15.0, 15.5, 16.5, 17.0, 17.0 and 17.0 kV/mm, respectively. Data obtained from thermal stability, hydrophobic behavior and dielectric studies it was inferred that the hybrid polymer composites developed in the present work can be conveniently used in the form insulators, sealants, adhesives and matrices where application demands at high‐performance industrial and engineering applications.