Bulbul Mauletbekova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Bulbul Mauletbekova has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Beibit Myrzakhmetov
Satbayev University
6 shared publications - Bibinur Akhymbayeva
Satbayev University
6 shared publications - Bakytzhan Kaliyev
Satbayev University
5 shared publications - Gulzada Mashatayeva
Satbayev University
5 shared publications - G.S. Serali
Satbayev University
3 shared publications - S.Z. Kabdulov3 shared publications
Latest Publications
- 30 October 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 155 (5) , 124-140
TECHNOLOGY FOR THE UTILIZATION OF SPENT DRILLING FLUIDS USING A HYDRODYNAMIC DISPERSER
The aim of this study is to develop a technology for the utilization and reuse of water-based spent drilling fluids from technological wells in the Republic of Kazakhstan using a hydrodynamic disperser, and to experimentally validate its effectiveness. The proposed technological solution enables efficient phase separation of drilling fluids, reduces the residual moisture content of the solid fraction, and allows the reuse of the liquid phase. The paper comprehensively examines the geological and hydrogeological conditions of technological wells, the composition and properties of drilling fluids, issues related to their accumulation and utilization, as well as the regulatory framework of the Republic of Kazakhstan governing drilling waste management. The design of the proposed hydrodynamic disperser and the technological process are described, and its advantages over conventional utilization methods are substantiated. In addition, the environmental, operational, and resource-efficiency aspects of implementing the proposed technology in existing drilling systems are analyzed.
- 30 October 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 155 (5) , 124-140
TECHNOLOGY FOR THE UTILIZATION OF SPENT DRILLING FLUIDS USING A HYDRODYNAMIC DISPERSER
The aim of this study is to develop a technology for the utilization and reuse of water-based spent drilling fluids from technological wells in the Republic of Kazakhstan using a hydrodynamic disperser, and to experimentally validate its effectiveness. The proposed technological solution enables efficient phase separation of drilling fluids, reduces the residual moisture content of the solid fraction, and allows the reuse of the liquid phase. The paper comprehensively examines the geological and hydrogeological conditions of technological wells, the composition and properties of drilling fluids, issues related to their accumulation and utilization, as well as the regulatory framework of the Republic of Kazakhstan governing drilling waste management. The design of the proposed hydrodynamic disperser and the technological process are described, and its advantages over conventional utilization methods are substantiated. In addition, the environmental, operational, and resource-efficiency aspects of implementing the proposed technology in existing drilling systems are analyzed.
- 30 August 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 154 (4) , 86-95
SHOCK-WAVE STIMULATION FOR DYNAMIC NEAR-WELLBORE TREATMENT IN TIGHT RESERVOIRS
The paper presents the results of theoretical and hydrodynamic substantiation of shockwave stimulation parameters for dynamic near-wellbore treatment and skin-factor reduction in tight reservoirs. The study is based on actual geological and technical data from production wells No. 45 and No. 47 of the Lower Visean substage at the «Х» field. A two-dimensional axisymmetric finite element model based on the Biot-Frenkel dynamic poroelasticity theory was developed, which accounts for the radial change in fluid viscosity and density within the zone of deep invasion of heavy mud filtrate (1.90 g/cm³). Through numerical simulation, the optimal frequency range of the shock pulse (10–15 Hz) was determined. It was established that the pressure wave with an amplitude of up to 4.5 MPa generated by the hydraulic impulse system exceeds the tensile strength of the rock (σt = 2.8 MPa) and ensures the opening of a microfracture network according to Coulomb’s cubic law at a distance of up to 2.0 m from the wellbore wall at a frequency of 10 Hz. The practical significance lies in the elimination of the mud cake screen formed under high overbalance conditions during the primary disclosure of an ultra-tight formation (porosity up to 0.15%, permeability from 0.001 mD). The implementation of the proposed regimes allows for a reduction in the calculated skin factor from critical 8.8 down to 0.4–1.5, which provides a 2.4 to 3.1-fold increase in the predicted well productivity index.
- 30 August 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 154 (4) , 86-95
SHOCK-WAVE STIMULATION FOR DYNAMIC NEAR-WELLBORE TREATMENT IN TIGHT RESERVOIRS
The paper presents the results of theoretical and hydrodynamic substantiation of shockwave stimulation parameters for dynamic near-wellbore treatment and skin-factor reduction in tight reservoirs. The study is based on actual geological and technical data from production wells No. 45 and No. 47 of the Lower Visean substage at the «Х» field. A two-dimensional axisymmetric finite element model based on the Biot-Frenkel dynamic poroelasticity theory was developed, which accounts for the radial change in fluid viscosity and density within the zone of deep invasion of heavy mud filtrate (1.90 g/cm³). Through numerical simulation, the optimal frequency range of the shock pulse (10–15 Hz) was determined. It was established that the pressure wave with an amplitude of up to 4.5 MPa generated by the hydraulic impulse system exceeds the tensile strength of the rock (σt = 2.8 MPa) and ensures the opening of a microfracture network according to Coulomb’s cubic law at a distance of up to 2.0 m from the wellbore wall at a frequency of 10 Hz. The practical significance lies in the elimination of the mud cake screen formed under high overbalance conditions during the primary disclosure of an ultra-tight formation (porosity up to 0.15%, permeability from 0.001 mD). The implementation of the proposed regimes allows for a reduction in the calculated skin factor from critical 8.8 down to 0.4–1.5, which provides a 2.4 to 3.1-fold increase in the predicted well productivity index.
- 30 August 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 154 (4) , 108-120
APPLICATION OF A HYDRODYNAMIC DISPERSER FOR THE UTILIZATION OF SPENT DRILLING FLUIDS
The paper presents the results of research aimed at improving the efficiency of spent drilling fluid utilization generated during the drilling of technological wells. The main objective of the study is to reduce the volume of generated sludge through efficient separation of solid and liquid phases and the reuse of separation products within the production cycle. The influence of hydrodynamic factors, including velocity gradient, treatment time, and reagent dosage, on the suspension settling process was investigated. The scientific novelty of the study lies in the use of a cylindrical hydrodynamic disperser for spent drilling fluid utilization and in determining the influence of its operating parameters on phase separation efficiency. A cylindrical-type hydrodynamic disperser providing controlled turbulent action on the suspension was developed. This ensures uniform distribution of reagents and improves particle coagulation efficiency compared to conventional designs. Laboratory studies established the optimal process parameters: velocity gradient – 1500 c-1, treatment time – 15 s, and N-300 reagent dosage – 50 g⁄(t ). Implementation of the proposed technology provides recovery of up to 80% of technical water from the solid phase, reduces the volume of generated sludge by 40–60%, and improves the environmental and resource efficiency of drilling operations.
- 30 August 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 154 (4) , 108-120
APPLICATION OF A HYDRODYNAMIC DISPERSER FOR THE UTILIZATION OF SPENT DRILLING FLUIDS
The paper presents the results of research aimed at improving the efficiency of spent drilling fluid utilization generated during the drilling of technological wells. The main objective of the study is to reduce the volume of generated sludge through efficient separation of solid and liquid phases and the reuse of separation products within the production cycle. The influence of hydrodynamic factors, including velocity gradient, treatment time, and reagent dosage, on the suspension settling process was investigated. The scientific novelty of the study lies in the use of a cylindrical hydrodynamic disperser for spent drilling fluid utilization and in determining the influence of its operating parameters on phase separation efficiency. A cylindrical-type hydrodynamic disperser providing controlled turbulent action on the suspension was developed. This ensures uniform distribution of reagents and improves particle coagulation efficiency compared to conventional designs. Laboratory studies established the optimal process parameters: velocity gradient – 1500 c-1, treatment time – 15 s, and N-300 reagent dosage – 50 g⁄(t ). Implementation of the proposed technology provides recovery of up to 80% of technical water from the solid phase, reduces the volume of generated sludge by 40–60%, and improves the environmental and resource efficiency of drilling operations.
- 30 April 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 152 (2) , 99-109
Optimization of hydraulic impact system parameters for drilling in tight reservoirs
The paper presents the results of hydrodynamic substantiation of hydraulic impact system parameters to enhance sidetracking efficiency in tight carbonate formations. The study is based on field data from well reconstruction in the Pre-Caspian Basin. A mathematical model based on the Zhukovsky equation was developed to describe wave processes in the drill string, accounting for the rheological properties of high-density polymer drilling fluids (1.22–1.28 g/cm³). Through numerical simulation, an optimal impact frequency range of 10–15 Hz was identified, facilitating the transition from static to dynamic rock failure modes. It was established that the system implementation minimizes the mechanical specific energy (MSE) and promotes the formation of a pre-fracture zone up to 3 mm deep. The practical significance lies in the formulation of technological recommendations for PDC bit drilling regimes under limited radial clearance conditions (149.2 mm). The proposed regimes ensure a 25–40% increase in the rate of penetration (ROP) while maintaining wellbore wall stability. The research findings allow for reducing the energy intensity of the rock failure process and shortening well construction timelines in complex geo-technical conditions.
- 30 April 2026
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 152 (2) , 99-109
Optimization of hydraulic impact system parameters for drilling in tight reservoirs
The paper presents the results of hydrodynamic substantiation of hydraulic impact system parameters to enhance sidetracking efficiency in tight carbonate formations. The study is based on field data from well reconstruction in the Pre-Caspian Basin. A mathematical model based on the Zhukovsky equation was developed to describe wave processes in the drill string, accounting for the rheological properties of high-density polymer drilling fluids (1.22–1.28 g/cm³). Through numerical simulation, an optimal impact frequency range of 10–15 Hz was identified, facilitating the transition from static to dynamic rock failure modes. It was established that the system implementation minimizes the mechanical specific energy (MSE) and promotes the formation of a pre-fracture zone up to 3 mm deep. The practical significance lies in the formulation of technological recommendations for PDC bit drilling regimes under limited radial clearance conditions (149.2 mm). The proposed regimes ensure a 25–40% increase in the rate of penetration (ROP) while maintaining wellbore wall stability. The research findings allow for reducing the energy intensity of the rock failure process and shortening well construction timelines in complex geo-technical conditions.
- Open Access
- 26 August 2025
- Published by Innovative Research Publishing in International Journal of Innovative Research and Scientific Studies
- Vol. 8 (6) , 2601-2610
Innovative technology for the reuse of spent drilling fluids in production well drilling using a hydraulic disperser
This article explores an innovative approach to the disposal of used water-based spent drilling fluids (SDF) utilized in the drilling of production wells at uranium deposits, with a case study based on the operations of SD «Inkai». A technological solution is proposed, centered on the use of a hydrodynamic disperser that enables efficient phase separation of drilling fluids, reduction of residual moisture in solid fractions, and the potential for reuse of the liquid phase. The geological and hydrogeological conditions of the deposit are examined in detail, along with the composition and properties of the drilling fluids, challenges associated with their accumulation and disposal, and the legal and regulatory framework of the Republic of Kazakhstan governing drilling waste management. The design of the proposed disperser is presented, the technological process is described, and its advantages over traditional disposal methods are substantiated. The article also analyzes the ecological, operational, and resource-saving aspects related to the implementation of the proposed technology within existing drilling systems.
- 26 August 2025
- Published by Innovative Research Publishing in International Journal of Innovative Research and Scientific Studies
- Vol. 8 (6) , 2601-2610
Open AccessInnovative technology for the reuse of spent drilling fluids in production well drilling using a hydraulic disperser
This article explores an innovative approach to the disposal of used water-based spent drilling fluids (SDF) utilized in the drilling of production wells at uranium deposits, with a case study based on the operations of SD «Inkai». A technological solution is proposed, centered on the use of a hydrodynamic disperser that enables efficient phase separation of drilling fluids, reduction of residual moisture in solid fractions, and the potential for reuse of the liquid phase. The geological and hydrogeological conditions of the deposit are examined in detail, along with the composition and properties of the drilling fluids, challenges associated with their accumulation and disposal, and the legal and regulatory framework of the Republic of Kazakhstan governing drilling waste management. The design of the proposed disperser is presented, the technological process is described, and its advantages over traditional disposal methods are substantiated. The article also analyzes the ecological, operational, and resource-saving aspects related to the implementation of the proposed technology within existing drilling systems.
- 30 June 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- No. 3,p. 88-101
Operation of downhole pumps under sanding conditions
One of the unfavourable factors of downhole pumping equipment operation at the fields at the final stage of development is high content of mechanical impurities in the pumped fluid. Similar problems are observed in fields with friable, weakly cemented formations, the fracture products of which flow downhole, resulting in lower extraction rates, equipment damage and higher operating costs. In oil production practice various technological measures and technical means are used to reduce the negative impact of sand penetration - regulation and optimisation of pumping equipment operation mode to ensure a rational rate of fluid withdrawal, application of technical devices in the form of sand filters and sand anchors and others. However, these measures and recommendations, for the most part, work successfully in the modes of continuous operation of wells. With the growing number of oil fields at the final stage of development, the issue of sanding becomes more and more urgent, as due to low flow rate wells at such fields are often switched to the mode of periodic operation, which favours the formation of sand plugs in tubing above the pump due to sufficient time for sedimentation of mechanical impurities. This can lead to pump jamming or rod breakage during subsequent well pump start-up. The experience of using sand filters (frame, slotted and others) in the arrangement of downhole pumps has shown that it does not always effectively solve the problem of sand penetration due to clogging of their cells with mechanical impurities and increased hydraulic resistance. This negatively affects the pumping equipment operation due to the shift of characteristics into the zone of suboptimal modes with associated problems for the electric drive. This makes it necessary to carry out underground well workover with removal of deep well pumping equipment for replacement or washing of the filter in surface conditions, as due to their peculiarities in the well pump layout (the filter is located at the intake of the pumping section), washing in well conditions is not always possible. These problems require not only the creation of effective downhole devices to prevent sand ingress to the pump intake or devices to prevent sand plugs above it, but also acceptable in practice calculation methods for predicting the sedimentation time of mechanical impurities in tubing or determining the minimum required speed of upward oil flow for stable sand removal. These calculation methods would also allow to reasonably regulate the time of technological interruptions while waiting for the wells to start up in periodic operation modes or to predict the time of activation of sand control devices for discharging the sand accumulated above the pump. This is the subject of this article. As a result of calculation analysis it was established that the main factors affecting the sedimentation process of mechanical impurities in the well are the speed and mode of fluid movement, its viscosity, density and size of the impurities themselves. Moreover, the most sensitive for the calculation accuracy is to take into account the change of fluid viscosity as it moves along the tubing as a result of heat exchange and the change of dissolved gas content due to pressure drop. Although at this stage the proposed methodology does not take into account some factors that can make additional adjustments to the process of sand sedimentation, however, it allows to predict with acceptable accuracy the time of technological interruptions in the well operation to prevent the formation of sand plugs, or the rational mode of operation of pumping equipment, providing the necessary speed of upward flow in the pipe for sand removal.
- 30 June 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- No. 3,p. 88-101
Operation of downhole pumps under sanding conditions
One of the unfavourable factors of downhole pumping equipment operation at the fields at the final stage of development is high content of mechanical impurities in the pumped fluid. Similar problems are observed in fields with friable, weakly cemented formations, the fracture products of which flow downhole, resulting in lower extraction rates, equipment damage and higher operating costs. In oil production practice various technological measures and technical means are used to reduce the negative impact of sand penetration - regulation and optimisation of pumping equipment operation mode to ensure a rational rate of fluid withdrawal, application of technical devices in the form of sand filters and sand anchors and others. However, these measures and recommendations, for the most part, work successfully in the modes of continuous operation of wells. With the growing number of oil fields at the final stage of development, the issue of sanding becomes more and more urgent, as due to low flow rate wells at such fields are often switched to the mode of periodic operation, which favours the formation of sand plugs in tubing above the pump due to sufficient time for sedimentation of mechanical impurities. This can lead to pump jamming or rod breakage during subsequent well pump start-up. The experience of using sand filters (frame, slotted and others) in the arrangement of downhole pumps has shown that it does not always effectively solve the problem of sand penetration due to clogging of their cells with mechanical impurities and increased hydraulic resistance. This negatively affects the pumping equipment operation due to the shift of characteristics into the zone of suboptimal modes with associated problems for the electric drive. This makes it necessary to carry out underground well workover with removal of deep well pumping equipment for replacement or washing of the filter in surface conditions, as due to their peculiarities in the well pump layout (the filter is located at the intake of the pumping section), washing in well conditions is not always possible. These problems require not only the creation of effective downhole devices to prevent sand ingress to the pump intake or devices to prevent sand plugs above it, but also acceptable in practice calculation methods for predicting the sedimentation time of mechanical impurities in tubing or determining the minimum required speed of upward oil flow for stable sand removal. These calculation methods would also allow to reasonably regulate the time of technological interruptions while waiting for the wells to start up in periodic operation modes or to predict the time of activation of sand control devices for discharging the sand accumulated above the pump. This is the subject of this article. As a result of calculation analysis it was established that the main factors affecting the sedimentation process of mechanical impurities in the well are the speed and mode of fluid movement, its viscosity, density and size of the impurities themselves. Moreover, the most sensitive for the calculation accuracy is to take into account the change of fluid viscosity as it moves along the tubing as a result of heat exchange and the change of dissolved gas content due to pressure drop. Although at this stage the proposed methodology does not take into account some factors that can make additional adjustments to the process of sand sedimentation, however, it allows to predict with acceptable accuracy the time of technological interruptions in the well operation to prevent the formation of sand plugs, or the rational mode of operation of pumping equipment, providing the necessary speed of upward flow in the pipe for sand removal.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 140 (2) , 93-106
Theoretical studies of the process of crack formation during rotational impact drilling
This article is devoted to the study of the process of crack formation, which are actively manifested during rotational impact drilling. The studies conducted during the writing of the article show that simultaneously with the destruction of the bottom of the well, another process occurs – the formation of many cracks in the angular (peripheral) zones of the bottom and on the walls of the well, going to a depth of 5-10 mm. These cracks remain in the form of a dense network in the walls of wells and in the core (during its selection), and the depth of the cracks increases with increasing impact energy. An attempt was made to explain the mechanism of cracking in the core during impact-rotational drilling from the standpoint of the theory of off-center impact. However, the study of cracking occurred when drilling wells on blocks of rocks. With the rotary-impact method of drilling deep horizontal wells, the types and distribution of loads in the near-well array will be different. This article presents technologies that increase the volume of production in depleted fields. During the calculations, the dependences of the impact force of the transmitted seal (rock) depending on its compliance are given. In addition, a graph of the dependence of changes in the impact force of the striker on the anvil on the impact time with different malleability of the anvil is constructed. The process of forming a horizontal well, which is drilled with a continuous face in a shock-rotational way using hydraulic impact machines, is considered. To study the process model, the results of solving the problem of stress distribution around the trunk array of a vertical well were considered.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 140 (2) , 93-106
Theoretical studies of the process of crack formation during rotational impact drilling
This article is devoted to the study of the process of crack formation, which are actively manifested during rotational impact drilling. The studies conducted during the writing of the article show that simultaneously with the destruction of the bottom of the well, another process occurs – the formation of many cracks in the angular (peripheral) zones of the bottom and on the walls of the well, going to a depth of 5-10 mm. These cracks remain in the form of a dense network in the walls of wells and in the core (during its selection), and the depth of the cracks increases with increasing impact energy. An attempt was made to explain the mechanism of cracking in the core during impact-rotational drilling from the standpoint of the theory of off-center impact. However, the study of cracking occurred when drilling wells on blocks of rocks. With the rotary-impact method of drilling deep horizontal wells, the types and distribution of loads in the near-well array will be different. This article presents technologies that increase the volume of production in depleted fields. During the calculations, the dependences of the impact force of the transmitted seal (rock) depending on its compliance are given. In addition, a graph of the dependence of changes in the impact force of the striker on the anvil on the impact time with different malleability of the anvil is constructed. The process of forming a horizontal well, which is drilled with a continuous face in a shock-rotational way using hydraulic impact machines, is considered. To study the process model, the results of solving the problem of stress distribution around the trunk array of a vertical well were considered.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 140 (2) , 133-146
Application of digital technologies in the management of oil well pumping systems in oil extraction
In recent years, one of the trends in oil well production has been the continuous growth of interest in intelligent monitoring and control systems for mechanized well assets. This is attributed, on one hand, to the increasing number of oil fields worldwide reaching maturity and the development of new challenging reservoirs (in terms of viscosity, water cut, and sand production). On the other hand, it is driven by the necessity to enhance the economic efficiency of oil production, including cost reduction and minimizing losses. The emergence of «smart» oil production technologies, such as programmable drives for well pumps, also contributes significantly to addressing these issues. Their application allows for increased reliability and lifespan of pump equipment, reduced well downtime and failures, prevention of negative scenarios during oil production, and facilitates the visualization of parameters in a user-friendly manner. Despite the widespread use of digital technologies in the oil and gas industry, there is still significant potential for further digitization to expand operations for enhanced safety and productivity. This article presents the experience of creating and testing such a control station for screw pump units at an oil field.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 140 (2) , 133-146
Application of digital technologies in the management of oil well pumping systems in oil extraction
In recent years, one of the trends in oil well production has been the continuous growth of interest in intelligent monitoring and control systems for mechanized well assets. This is attributed, on one hand, to the increasing number of oil fields worldwide reaching maturity and the development of new challenging reservoirs (in terms of viscosity, water cut, and sand production). On the other hand, it is driven by the necessity to enhance the economic efficiency of oil production, including cost reduction and minimizing losses. The emergence of «smart» oil production technologies, such as programmable drives for well pumps, also contributes significantly to addressing these issues. Their application allows for increased reliability and lifespan of pump equipment, reduced well downtime and failures, prevention of negative scenarios during oil production, and facilitates the visualization of parameters in a user-friendly manner. Despite the widespread use of digital technologies in the oil and gas industry, there is still significant potential for further digitization to expand operations for enhanced safety and productivity. This article presents the experience of creating and testing such a control station for screw pump units at an oil field.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 139 (1) , 52-60
THE FEATURES OF WORK OF CARBIDE-TIPPED DRILL IN CRUMBLING ROCKS
The drill bit in the oil and gas industry plays a key role in the drilling process, but its operation in the field, filled with difficulties and dangers, emphasizes the need for careful study of its behavior. This equipment, which is the head of the well, is forced to face various challenges during drilling, where danger can await at every step. However, special attention should be paid to those cases when the drill bit collides with crumbling rocks. In conditions of high pressure and friction associated with drilling, the drill bit is subjected to significant loads. These conditions can lead to damage and breakage of equipment, which in turn creates additional risks for workers on site. Understanding the behavior of a drill bit in crumbling rock is becoming an extremely important aspect to ensure the efficiency and safety of field work. The analysis of the technical characteristics and mechanisms of the impact of the drill bit on crumbling rocks makes it possible to develop more reliable and durable tools capable of withstanding extreme conditions. This, in turn, increases drilling efficiency, reduces the risk of industrial accidents and ensures safer working conditions in the oil and gas industry.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 139 (1) , 52-60
THE FEATURES OF WORK OF CARBIDE-TIPPED DRILL IN CRUMBLING ROCKS
The drill bit in the oil and gas industry plays a key role in the drilling process, but its operation in the field, filled with difficulties and dangers, emphasizes the need for careful study of its behavior. This equipment, which is the head of the well, is forced to face various challenges during drilling, where danger can await at every step. However, special attention should be paid to those cases when the drill bit collides with crumbling rocks. In conditions of high pressure and friction associated with drilling, the drill bit is subjected to significant loads. These conditions can lead to damage and breakage of equipment, which in turn creates additional risks for workers on site. Understanding the behavior of a drill bit in crumbling rock is becoming an extremely important aspect to ensure the efficiency and safety of field work. The analysis of the technical characteristics and mechanisms of the impact of the drill bit on crumbling rocks makes it possible to develop more reliable and durable tools capable of withstanding extreme conditions. This, in turn, increases drilling efficiency, reduces the risk of industrial accidents and ensures safer working conditions in the oil and gas industry.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 139 (1) , 39-51
ANALYSIS OF LABORATORY STUDIES OF HYDROPHOBIC EMULSIONS TO ENSURE WATER INSULATION WORK IN OIL FIELDS
This article is devoted to the research and implementation of methods for ensuring water insulation works (WIW) in the oil sector using hydrophobic emulsions. In the context of modern requirements for environmental safety and efficiency of production processes in the oil industry, where water can become a source of problems, the introduction of innovative materials and technologies plays an important role. Conducting laboratory studies of hydrophobic emulsions for WIW in the oil sector is a multiprocess approach, starting from the initial assessment of the chemical component and ending with thorough testing for compliance with the requirements of specific operating conditions. The analysis evaluates the physico-chemical properties of the emulsion, such as density, viscosity, pH level, degree of dispersion, as well as its adhesive and cohesive characteristics. Special attention is paid to the study of the surface properties of hydrophobic emulsions, since their ability to form stable water-repellent coatings directly affects the effectiveness of protection against water exposure. To do this, tests are carried out on wettability, contact angle, adhesion to various types of surfaces, which allows us to determine the optimal conditions for the use of emulsions in specific situations. The article describes the principles of action of hydrophobic emulsions in the context of waterproofing works, emphasizing their ability to create a protective barrier, preventing moisture penetration into oil facilities. The paper presents the results of laboratory studies demonstrating the effectiveness of the use of hydrophobic emulsions in various operating conditions. The article discusses the technical aspects of the use of hydrophobic emulsions in the WIW process, analyzes their resistance to various environmental factors, and also considers the prospects for the development of this technology in the oil industry. The results obtained can be useful for specialists dealing with water insulation in oil companies, as well as for the scientific and engineering community interested in the development of innovative technologies in the oil sector. The purpose of this article is to analyze laboratory research and provide recommendations on the use of polymer composition.
- 15 February 2024
- Published by Oil Research and Engineering Center of the National Engineering Academy of the Republic of Kazakhstan in Neft i Gaz
- Vol. 139 (1) , 39-51
ANALYSIS OF LABORATORY STUDIES OF HYDROPHOBIC EMULSIONS TO ENSURE WATER INSULATION WORK IN OIL FIELDS
This article is devoted to the research and implementation of methods for ensuring water insulation works (WIW) in the oil sector using hydrophobic emulsions. In the context of modern requirements for environmental safety and efficiency of production processes in the oil industry, where water can become a source of problems, the introduction of innovative materials and technologies plays an important role. Conducting laboratory studies of hydrophobic emulsions for WIW in the oil sector is a multiprocess approach, starting from the initial assessment of the chemical component and ending with thorough testing for compliance with the requirements of specific operating conditions. The analysis evaluates the physico-chemical properties of the emulsion, such as density, viscosity, pH level, degree of dispersion, as well as its adhesive and cohesive characteristics. Special attention is paid to the study of the surface properties of hydrophobic emulsions, since their ability to form stable water-repellent coatings directly affects the effectiveness of protection against water exposure. To do this, tests are carried out on wettability, contact angle, adhesion to various types of surfaces, which allows us to determine the optimal conditions for the use of emulsions in specific situations. The article describes the principles of action of hydrophobic emulsions in the context of waterproofing works, emphasizing their ability to create a protective barrier, preventing moisture penetration into oil facilities. The paper presents the results of laboratory studies demonstrating the effectiveness of the use of hydrophobic emulsions in various operating conditions. The article discusses the technical aspects of the use of hydrophobic emulsions in the WIW process, analyzes their resistance to various environmental factors, and also considers the prospects for the development of this technology in the oil industry. The results obtained can be useful for specialists dealing with water insulation in oil companies, as well as for the scientific and engineering community interested in the development of innovative technologies in the oil sector. The purpose of this article is to analyze laboratory research and provide recommendations on the use of polymer composition.