SKS.Z. Kabdulov

S.Z. Kabdulov

*This is an algorithmically generated author record based on publicly available information.

S.Z. Kabdulov has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Features of drilling horizontal wells with gas-liquid shock-ejector shells in difficult mining and geological conditions

    by Satbayev University, B.S. Akhymbayeva, S.Z. Kabdulov, Kazakh-British Technical University, B.A. Myrzakhmetov, B.Z. Kaliyev, T.A. Kuandykov

    This article examines the features of drilling horizontal wells with gas-liquid shock-ejector shells in difficult mining and geological conditions, namely in boulder-pebble deposits. The technology of drilling large boulders is considered. In addition, to study the processes of energy transfer and shock pulses from the drilling shell to the bottom of the well during the sinking of boulders, the authors conducted appropriate theoretical studies and provided calculations of the stages of the introduction of the tool into the rock. Based on theoretical studies, drilling analysis, calculations of the dependence of boulder movements, several conclusions were obtained on the technology of drilling wells in boulder-nut deposits.

  • Theoretical studies of the process of crack formation during rotational impact drilling

    by B.S. Akhymbayeva, Satbayev University, S.Z. Kabdulov, B.K. Mauletbekova, T.A. Kuandykov, G.A. Mashatayeva, Kazakh-British Technical University

    This article is devoted to the study of the process of crack formation, which are actively manifested during rotational impact drilling. The studies conducted during the writing of the article show that simultaneously with the destruction of the bottom of the well, another process occurs – the formation of many cracks in the angular (peripheral) zones of the bottom and on the walls of the well, going to a depth of 5-10 mm. These cracks remain in the form of a dense network in the walls of wells and in the core (during its selection), and the depth of the cracks increases with increasing impact energy. An attempt was made to explain the mechanism of cracking in the core during impact-rotational drilling from the standpoint of the theory of off-center impact. However, the study of cracking occurred when drilling wells on blocks of rocks. With the rotary-impact method of drilling deep horizontal wells, the types and distribution of loads in the near-well array will be different. This article presents technologies that increase the volume of production in depleted fields. During the calculations, the dependences of the impact force of the transmitted seal (rock) depending on its compliance are given. In addition, a graph of the dependence of changes in the impact force of the striker on the anvil on the impact time with different malleability of the anvil is constructed. The process of forming a horizontal well, which is drilled with a continuous face in a shock-rotational way using hydraulic impact machines, is considered. To study the process model, the results of solving the problem of stress distribution around the trunk array of a vertical well were considered.

  • ANALYSIS OF LABORATORY STUDIES OF HYDROPHOBIC EMULSIONS TO ENSURE WATER INSULATION WORK IN OIL FIELDS

    by SATBAYEV UNIVERSITY, B.S. Akhymbayeva, S.Z. Kabdulov, KAZAKH-BRITISH TECHNICAL UNIVERSITY, B.K. Mauletbekov, A.Kh. Syzdykov, A.T. Bakesheva

    This article is devoted to the research and implementation of methods for ensuring water insulation works (WIW) in the oil sector using hydrophobic emulsions. In the context of modern requirements for environmental safety and efficiency of production processes in the oil industry, where water can become a source of problems, the introduction of innovative materials and technologies plays an important role. Conducting laboratory studies of hydrophobic emulsions for WIW in the oil sector is a multiprocess approach, starting from the initial assessment of the chemical component and ending with thorough testing for compliance with the requirements of specific operating conditions. The analysis evaluates the physico-chemical properties of the emulsion, such as density, viscosity, pH level, degree of dispersion, as well as its adhesive and cohesive characteristics. Special attention is paid to the study of the surface properties of hydrophobic emulsions, since their ability to form stable water-repellent coatings directly affects the effectiveness of protection against water exposure. To do this, tests are carried out on wettability, contact angle, adhesion to various types of surfaces, which allows us to determine the optimal conditions for the use of emulsions in specific situations. The article describes the principles of action of hydrophobic emulsions in the context of waterproofing works, emphasizing their ability to create a protective barrier, preventing moisture penetration into oil facilities. The paper presents the results of laboratory studies demonstrating the effectiveness of the use of hydrophobic emulsions in various operating conditions. The article discusses the technical aspects of the use of hydrophobic emulsions in the WIW process, analyzes their resistance to various environmental factors, and also considers the prospects for the development of this technology in the oil industry. The results obtained can be useful for specialists dealing with water insulation in oil companies, as well as for the scientific and engineering community interested in the development of innovative technologies in the oil sector. The purpose of this article is to analyze laboratory research and provide recommendations on the use of polymer composition.

  • ANALYSIS OF THE MANIFESTATION OF CRACKS IN ROCKS DURING HYDRAULIC HAMMER DRILLING

    by SATBAYEV UNIVERSITY, B.S. Akhymbayeva, S.Z. Kabdulov, KAZAKH-BRITISH TECHNICAL UNIVERSITY, B.K. Mauletbekova, A.KH. Syzdykov, A.T. Bakesheva

    This article is devoted to the study of the process of crack formation in rocks during hydraulic hammer drilling. Analysis of the manifestation of cracks in rocks during hydraulic percussion drilling is a key aspect of research aimed at the optimization and efficiency of this drilling method. The article presents a comprehensive analysis of the mechanisms of crack formation in rocks under the influence of hydraulic shock waves, identifying factors influencing their development and propagation. The work highlights the basic principles and mechanisms of hydraulic percussion drilling, and also analyzes the factors influencing the formation of cracks in rocks during this drilling method. In addition, various parameters such as water pressure, impact velocity, tool type and rock characteristics are considered and their influence on fracture formation. The paper presents numerical modeling and calculation methods used to analyze the factors influencing the formation of cracks during well drilling. Basic parameters are considered, such as well depth, type of drilling equipment used, physical and mechanical properties of the rock, drilling fluid pressure and others. Examples of numerical calculations and modeling are given, as well as an assessment of the influence of various factors on the formation of cracks in rock. The purpose of this article is to summarize current information on the formation of cracks during the hydraulic percussion drilling method. The scientific significance of this study lies in the possibility of predicting and controlling the formation of cracks during hydraulic drilling, which contributes to more efficient use of resources and improved drilling safety. The results obtained can be used in the practice of geological exploration and mining work to optimize drilling processes and improve the quality of mineral extraction. Understanding the processes of formation of cracks in rocks with this drilling method will allow optimizing its use, improving control over the process and ensuring more efficient and safe extraction of minerals from the bowels of the earth.