Yong-Woon Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yong-Woon Choi has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Young-Bok Kim
Department of Intelligent Robot Engineering, Pukyong National University, Busan, Republic of Korea
2 shared publications - Chang-Woo Kim
Korea Institute of Maritime and Fisheries Technology, Busan 49111, Republic of Korea
1 shared publication - Daiki Yuasa
Graduate School of Engineering, Soka University, Tokyo 192-8577, Japan
1 shared publication - Eun-Jae Wi
Department of Mechanical System Engineering, the Graduate School, Pukyong National University, Busan 48513, Republic of Korea
1 shared publication - Hyoung-Jin Kim
Samsung Electronics, Cheonan 31086, Republic of Korea
1 shared publication - Jung-Suk Park
Training Ship Baek-kyung, Pukyong National University, Busan 48513, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 20 November 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (11) , 1350
Development and Thermal Characterization of a Mechanically Packaged Hetero-Core Optical Fiber Temperature Sensor
This study presents the development and thermal characterization of a mechanically packaged Hetero-core optical fiber temperature sensor utilizing the thermal expansion of a silicone pad. To improve the insufficient optical-output recovery observed during cooling in our previous adhesive-fixed sensor, a poly(butylene succinate) (PBS)-based mechanical packaging structure was developed to replace direct adhesive fixation of the Hetero-core sensing region. Thermally induced deformation of the silicone pad produces variations in optical transmission loss, which are detected and converted into electrical voltage signals. Four sensor configurations, combining two silicone pad thicknesses and two Hetero-core insertion lengths, were evaluated using one specimen per configuration through three consecutive heating–cooling cycles over a temperature range of 20–80 °C. The experimental results demonstrated temperature-dependent responses with configuration-dependent differences in linearity, thermal hysteresis, and cycle-to-cycle repeatability. The configuration with a 2 mm thick silicone pad and a 2 mm Hetero-core insertion length exhibited the lowest average hysteresis (15.04% FS), whereas the configuration with a 5 mm thick pad and a 2 mm insertion length showed the lowest heating repeatability error (11.56% FS). The configuration with a 5 mm thick pad and a 3 mm insertion length exhibited the lowest cooling repeatability error (6.12% FS), indicating that the preferred sensor configuration depends on the performance criterion considered. Although further improvements in sensing performance and validation of measurement accuracy, response time, and device-to-device reproducibility are required, the results demonstrate the feasibility of the proposed approach for further development of optical fiber temperature sensors for abnormal-temperature monitoring in electrical equipment.
- 20 November 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (11) , 1350
Open AccessDevelopment and Thermal Characterization of a Mechanically Packaged Hetero-Core Optical Fiber Temperature Sensor
This study presents the development and thermal characterization of a mechanically packaged Hetero-core optical fiber temperature sensor utilizing the thermal expansion of a silicone pad. To improve the insufficient optical-output recovery observed during cooling in our previous adhesive-fixed sensor, a poly(butylene succinate) (PBS)-based mechanical packaging structure was developed to replace direct adhesive fixation of the Hetero-core sensing region. Thermally induced deformation of the silicone pad produces variations in optical transmission loss, which are detected and converted into electrical voltage signals. Four sensor configurations, combining two silicone pad thicknesses and two Hetero-core insertion lengths, were evaluated using one specimen per configuration through three consecutive heating–cooling cycles over a temperature range of 20–80 °C. The experimental results demonstrated temperature-dependent responses with configuration-dependent differences in linearity, thermal hysteresis, and cycle-to-cycle repeatability. The configuration with a 2 mm thick silicone pad and a 2 mm Hetero-core insertion length exhibited the lowest average hysteresis (15.04% FS), whereas the configuration with a 5 mm thick pad and a 2 mm insertion length showed the lowest heating repeatability error (11.56% FS). The configuration with a 5 mm thick pad and a 3 mm insertion length exhibited the lowest cooling repeatability error (6.12% FS), indicating that the preferred sensor configuration depends on the performance criterion considered. Although further improvements in sensing performance and validation of measurement accuracy, response time, and device-to-device reproducibility are required, the results demonstrate the feasibility of the proposed approach for further development of optical fiber temperature sensors for abnormal-temperature monitoring in electrical equipment.
- Open Access
- 3 November 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (11) , 1637
Development of a Portable Interface System Sharing the Positioning and Heading Information to Support a Berthing Vessel
The study develops a portable interface system to inform berthing operators of the position and heading in relation to the quay when berthing a large vessel equipped with distance-measuring instruments. A portable interface system is indispensable for preventing collisions and improving the efficiency of berthing operations because it allows operators to intuitively grasp the movement status of the vessel based on the distance data measured during berthing. These data can not only be converted into the current position and heading of the vessel relative to the quay, but can also be visualized to predict the movement and speed of the vessel in a few seconds. Therefore, we developed a visualization system using Rviz, a 3D model visualization tool for a robot operating system, and verified the necessity for an interface system through simulations and experiments using a model vessel. Furthermore, we extended the function of the visualization interface using a wireless network, developed a web application to display the vessel’s positioning information on multiple operators’ terminals, and verified the drawing stability at 10 Hz using the extended application.
- 3 November 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (11) , 1637
Open AccessDevelopment of a Portable Interface System Sharing the Positioning and Heading Information to Support a Berthing Vessel
The study develops a portable interface system to inform berthing operators of the position and heading in relation to the quay when berthing a large vessel equipped with distance-measuring instruments. A portable interface system is indispensable for preventing collisions and improving the efficiency of berthing operations because it allows operators to intuitively grasp the movement status of the vessel based on the distance data measured during berthing. These data can not only be converted into the current position and heading of the vessel relative to the quay, but can also be visualized to predict the movement and speed of the vessel in a few seconds. Therefore, we developed a visualization system using Rviz, a 3D model visualization tool for a robot operating system, and verified the necessity for an interface system through simulations and experiments using a model vessel. Furthermore, we extended the function of the visualization interface using a wireless network, developed a web application to display the vessel’s positioning information on multiple operators’ terminals, and verified the drawing stability at 10 Hz using the extended application.