Vinod Ashok Thale
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vinod Ashok Thale has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Mostafa Abouelsoud
Department of Mechanical Engineering, Faculty of Engineering, South Valley University, Qena 83521, Egypt
2 shared publications - Ahmed Nagah Shmroukh
Department of Mechanical Engineering, Faculty of Engineering, South Valley University, Qena 83523, Egypt
1 shared publication - Bofeng Bai
State Key Laboratory of Multiphase Flow in Power Engineering, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Hossain Chizari
Xi’an Jiaotong University (XJTU)
1 shared publication - Marie-Jean Thoraval
International Center for Applied Mechanics, State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace, Xi'an Jiaotong University 2 , Xi'an 710049
1 shared publication
Latest Publications
- Open Access
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Impact force of an air-in-liquid compound drop
We investigate numerically the transient forces produced by an air-in-liquid compound drop impacting onto a solid surface. We demonstrate that the presence of a bubble in the drop decreases the impact force. This decrease can be mainly explained by a reduced area over which the impact pressure is applied. We systematically vary the bubble size to understand its effect on the maximum normal force. A simple scaling model for the maximum impact force is developed to accommodate the effect of bubble size.
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Open AccessImpact force of an air-in-liquid compound drop
We investigate numerically the transient forces produced by an air-in-liquid compound drop impacting onto a solid surface. We demonstrate that the presence of a bubble in the drop decreases the impact force. This decrease can be mainly explained by a reduced area over which the impact pressure is applied. We systematically vary the bubble size to understand its effect on the maximum normal force. A simple scaling model for the maximum impact force is developed to accommodate the effect of bubble size.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11) , 112108
Spreading and retraction of the concentric impact of a drop with a sessile drop of the same liquid: Effect of surface wettability
The concentric impact on a sessile drop is relevant in many applications, including spray coating and icing phenomena. Herein, the spreading and retraction phases yielded during the impact of a coaxial drop with a sessile drop on a solid substrate were empirically and analytically examined. We analyzed the effects of surface wettability on the impact outcomes utilizing five distinctive surfaces (i.e., smooth glass, aluminum, copper, Teflon, and coated glass). The results showed that the merged drop takes longer to attain its maximum spreading diameter at a relatively higher contact angle of the sessile drop with the solid surface. Furthermore, based on energy balance, a model for predicting the maximum spreading diameter of the drop with varying surface wettability was presented. This model considers the assumption of viscous energy loss during the merging of falling and sessile drops and at the maximum spreading diameter. Additionally, the maximum retraction height during the impact on the coated glass surface was investigated. Our model results matched well with the experimental data.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11) , 112108
Spreading and retraction of the concentric impact of a drop with a sessile drop of the same liquid: Effect of surface wettability
The concentric impact on a sessile drop is relevant in many applications, including spray coating and icing phenomena. Herein, the spreading and retraction phases yielded during the impact of a coaxial drop with a sessile drop on a solid substrate were empirically and analytically examined. We analyzed the effects of surface wettability on the impact outcomes utilizing five distinctive surfaces (i.e., smooth glass, aluminum, copper, Teflon, and coated glass). The results showed that the merged drop takes longer to attain its maximum spreading diameter at a relatively higher contact angle of the sessile drop with the solid surface. Furthermore, based on energy balance, a model for predicting the maximum spreading diameter of the drop with varying surface wettability was presented. This model considers the assumption of viscous energy loss during the merging of falling and sessile drops and at the maximum spreading diameter. Additionally, the maximum retraction height during the impact on the coated glass surface was investigated. Our model results matched well with the experimental data.