Tuo Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tuo Shi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Jing Jiao
School of Automobile and Rail Transit, Nanjing Institute of Technology, Nanjing, China
1 shared publicationLiguo Zang
School of Traffic Engineering, Nanjing Institute of Technology, Nanjing 211167, China
1 shared publication- Pan Zhou
School of Traffic Engineering, Nanjing Institute of Technology, Nanjing, 211167, People’s Republic of China
1 shared publication Shaokang Chen
State Grid Fujian Electric Power Company Ltd., Fuzhou, China
1 shared publicationTian Lv
School of Traffic Engineering, Nanjing Institute of Technology, Nanjing 211167, China
1 shared publicationYaowei Li
School of Traffic Engineering, Nanjing Institute of Technology, Nanjing 211167, China
1 shared publication
Latest Publications
- Open Access
- 11 February 2025
- Published by EDP Sciences in Acta Acustica
- Vol. 9, 11
Simulation study on noise reduction of electric vehicle tire with built-in sound-absorbing material
Tire cavity noise is becoming more prominent as the speed of electric vehicles is getting higher. This study aims to use a built-in sound-absorbing material to reduce tire cavity noise. First, the radial force was extracted by rolling analysis, and the tire cavity noise was obtained. Then, in order to investigate how the placement of sound-absorbing material affects the noise reduction, sound-absorbing material was applied to the inner side of tire’s side and tread position respectively. Finally, studies were done on the impact of sound-absorbing material’s density, flow resistance, porosity, and thickness on tire noise reduction. The best way to reduce noise with a 215/55R17 tire was to apply sound-absorbing material at side position. The density, porosity, flow resistance and thickness of the sound-absorbing material were 55 kg/m3, 0.95, 5000 Pa·s/m2 and 40 mm, respectively. The A-weighted sound pressure level decreased by 27.7 dB compared with that before the built-in sound-absorbing material. In response to the uncertainties on the reduction achieved by the sound-absorbing material, this study offers some recommendations for noise reduction of tire cavity. The studied effect is limited to the tire cavity, and the effect on the emitted sound energy has not been evaluated.
- 11 February 2025
- Published by EDP Sciences in Acta Acustica
- Vol. 9, 11
Open AccessSimulation study on noise reduction of electric vehicle tire with built-in sound-absorbing material
Tire cavity noise is becoming more prominent as the speed of electric vehicles is getting higher. This study aims to use a built-in sound-absorbing material to reduce tire cavity noise. First, the radial force was extracted by rolling analysis, and the tire cavity noise was obtained. Then, in order to investigate how the placement of sound-absorbing material affects the noise reduction, sound-absorbing material was applied to the inner side of tire’s side and tread position respectively. Finally, studies were done on the impact of sound-absorbing material’s density, flow resistance, porosity, and thickness on tire noise reduction. The best way to reduce noise with a 215/55R17 tire was to apply sound-absorbing material at side position. The density, porosity, flow resistance and thickness of the sound-absorbing material were 55 kg/m3, 0.95, 5000 Pa·s/m2 and 40 mm, respectively. The A-weighted sound pressure level decreased by 27.7 dB compared with that before the built-in sound-absorbing material. In response to the uncertainties on the reduction achieved by the sound-absorbing material, this study offers some recommendations for noise reduction of tire cavity. The studied effect is limited to the tire cavity, and the effect on the emitted sound energy has not been evaluated.
- Open Access
- 1 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 116642-116649
Simulation Analysis of Grounding Characteristics of Cable Based on ATP-EMTP
In order to improve the operation safety and stability of power cables, it is necessary to conduct targeted research on different grounding modes. Firstly, the appropriate cable parameters are selected according to the specific use, and the model is established in ATP-EMTP according to the selected cable parameters. Then, the availability of three grounding modes models of grounding at one end, grounding at both ends and cross-connection grounding (cable core grounding, shielding layer grounding and armor layer grounding) are compared and verified by simulation. Finally, by setting the shielding layers of different thicknesses as a comparison, the impedance and current characteristics of the cables under three different grounding methods are analyzed. The results show that the impedance values of the three grounding methods are basically the same. However, according to the current characteristics, when the shielding layer and the armored layer are cross-connected and grounded, the current of them is much smaller than that which is grounded by other grounding methods. Therefore, under the comprehensive consideration of economic benefits, this grounding is the best choice. This study provides guidance for the grounding mode of cable early laying, and provides reference for other cable related research.
- 1 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 116642-116649
Open AccessSimulation Analysis of Grounding Characteristics of Cable Based on ATP-EMTP
In order to improve the operation safety and stability of power cables, it is necessary to conduct targeted research on different grounding modes. Firstly, the appropriate cable parameters are selected according to the specific use, and the model is established in ATP-EMTP according to the selected cable parameters. Then, the availability of three grounding modes models of grounding at one end, grounding at both ends and cross-connection grounding (cable core grounding, shielding layer grounding and armor layer grounding) are compared and verified by simulation. Finally, by setting the shielding layers of different thicknesses as a comparison, the impedance and current characteristics of the cables under three different grounding methods are analyzed. The results show that the impedance values of the three grounding methods are basically the same. However, according to the current characteristics, when the shielding layer and the armored layer are cross-connected and grounded, the current of them is much smaller than that which is grounded by other grounding methods. Therefore, under the comprehensive consideration of economic benefits, this grounding is the best choice. This study provides guidance for the grounding mode of cable early laying, and provides reference for other cable related research.