Asami Hatamoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Asami Hatamoto has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hiroyuki Nishida
Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Tokyo 184-8588, Japan
5 shared publications - Akinori Nishizawa2 shared publications
- Kenta Emori
Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan
2 shared publications - Shūji Ōtomo
Tokyo University of Agriculture and Technology
2 shared publications - Kumi Nakai
Department of Energy and Environment, National Institute of Advanced Industrial Science and Technology, Tsukuba, Ibaraki, Japan
1 shared publication Naoki Omori
1 shared publication
Latest Publications
- Open Access
- 28 April 2026
- Published by Elsevier in SSRN Electronic Journal
Modeling wall temperature in forced convection over a flat plate with a plasma actuator
Efficient heat transfer enhancement under forced convection is crucial for the performance and reliability of modern engineering systems. Dielectric barrier discharge plasma actuators (DBDPAs) have attracted attention for active heat transfer control. However, gas heating remains a challenge, as it often offsets the cooling effect of flow acceleration. We present a decoupled model that separates wall temperature changes into two components: flow-acceleration effects (Nusselt number changes) and gas-heating effects (temperature increase). The validity of this model was verified through numerical simulations. Our results confirm that the change in the Nusselt number is uniquely scaled by the thrust coefficient, consistent with prior studies. Furthermore, we find that the temperature increase due to gas heating varies linearly with the power consumption coefficient, with its proportionality determined by the thrust coefficient. Crucially, by combining these relations, this study demonstrates that the total net change in wall temperature induced by DBDPA driving can be explicitly formulated as a function of only two key dimensionless parameters: the thrust coefficient and the power consumption coefficient. This formulation enables the precise, quantitative prediction of the complex trade-off between acceleration-based cooling and thermal heating, providing essential design guidelines for optimizing DBDPA-based thermal management systems.
- 28 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessModeling wall temperature in forced convection over a flat plate with a plasma actuator
Efficient heat transfer enhancement under forced convection is crucial for the performance and reliability of modern engineering systems. Dielectric barrier discharge plasma actuators (DBDPAs) have attracted attention for active heat transfer control. However, gas heating remains a challenge, as it often offsets the cooling effect of flow acceleration. We present a decoupled model that separates wall temperature changes into two components: flow-acceleration effects (Nusselt number changes) and gas-heating effects (temperature increase). The validity of this model was verified through numerical simulations. Our results confirm that the change in the Nusselt number is uniquely scaled by the thrust coefficient, consistent with prior studies. Furthermore, we find that the temperature increase due to gas heating varies linearly with the power consumption coefficient, with its proportionality determined by the thrust coefficient. Crucially, by combining these relations, this study demonstrates that the total net change in wall temperature induced by DBDPA driving can be explicitly formulated as a function of only two key dimensionless parameters: the thrust coefficient and the power consumption coefficient. This formulation enables the precise, quantitative prediction of the complex trade-off between acceleration-based cooling and thermal heating, providing essential design guidelines for optimizing DBDPA-based thermal management systems.
- Open Access
- 29 April 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 247
Experimental evaluation of gas heating and flow modification effects by plasma actuator in forced-convection heat transfer
- 29 April 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 247
Open AccessExperimental evaluation of gas heating and flow modification effects by plasma actuator in forced-convection heat transfer
- 3 August 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (44) , 449501
Corrigendum: Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air (2023 J. Phys. D: Appl. Phys. 56 155203)
- 3 August 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (44) , 449501
Corrigendum: Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air (2023 J. Phys. D: Appl. Phys. 56 155203)
- 13 March 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (15) , 155203
Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air
Dielectric barrier discharge plasma actuators (DBDPAs) have been investigated for active flow control. The discharge induces ionic wind, which can be utilized for flow control; however, it simultaneously heats the flow and the dielectric surface. The thermal characteristics of the DBDPA must be clarified for applications in thermo-fluid engineering, such as forced convective cooling. In this study, we constructed a similarity law for the time variation of the surface temperature, assuming that the induced flow was heated by the discharge and that the dielectric was heated by the airflow. The similarity law was derived from the one-dimensional heat conduction equation in the dielectric, and the spatially averaged normalized temperature was then formulated as a function of the Biot and Fourier numbers. To experimentally validate the similarity law, the surface temperature, thrust, and power consumption were measured. The induced flow temperature and heat transfer coefficient were estimated based on the thrust and power consumption. The measured results verified that the similarity law was valid, regardless of the dielectric material, thickness, or applied voltage. This result supports the hypothesis regarding the heating mechanism in which the airflow is heated by Joule heating and the dielectric is heated by forced convection.
- 13 March 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (15) , 155203
Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air
Dielectric barrier discharge plasma actuators (DBDPAs) have been investigated for active flow control. The discharge induces ionic wind, which can be utilized for flow control; however, it simultaneously heats the flow and the dielectric surface. The thermal characteristics of the DBDPA must be clarified for applications in thermo-fluid engineering, such as forced convective cooling. In this study, we constructed a similarity law for the time variation of the surface temperature, assuming that the induced flow was heated by the discharge and that the dielectric was heated by the airflow. The similarity law was derived from the one-dimensional heat conduction equation in the dielectric, and the spatially averaged normalized temperature was then formulated as a function of the Biot and Fourier numbers. To experimentally validate the similarity law, the surface temperature, thrust, and power consumption were measured. The induced flow temperature and heat transfer coefficient were estimated based on the thrust and power consumption. The measured results verified that the similarity law was valid, regardless of the dielectric material, thickness, or applied voltage. This result supports the hypothesis regarding the heating mechanism in which the airflow is heated by Joule heating and the dielectric is heated by forced convection.
- Open Access
Experimental Study on the Working Characteristics of Tri-Electrode Plasma Actuator Utilizing a Combination of Corona and Barrier Discharges
A tri-electrode plasma actuator (TED-PA), which has an additional electrode with a DC voltage, induces jets from two facing electrodes and achieves larger thrust and higher efficiency than a conventional dielectric barrier discharge plasma actuator. However, there are problems such as the large potential difference between the exposed electrodes, which can cause sparks and device destruction. Therefore, it is necessary to clarify the working mechanism of TED-PAs and optimize their configuration and applied voltage. In this study, we obtained the discharge photograph, the thrust, and the flow velocity field and investigated the characteristics of the DC voltage and the frequency of the AC voltage. To isolate the effects of the discharge from the potential variation, a corona discharge plasma actuator and a TED-PA were compared. As a result, increasing the frequency of the AC voltage induced stronger jets from the AC and DC electrodes. This result indicates that the barrier discharge enhances the jet from the DC electrode without changing the potential difference between the electrodes.
Open AccessExperimental Study on the Working Characteristics of Tri-Electrode Plasma Actuator Utilizing a Combination of Corona and Barrier Discharges
A tri-electrode plasma actuator (TED-PA), which has an additional electrode with a DC voltage, induces jets from two facing electrodes and achieves larger thrust and higher efficiency than a conventional dielectric barrier discharge plasma actuator. However, there are problems such as the large potential difference between the exposed electrodes, which can cause sparks and device destruction. Therefore, it is necessary to clarify the working mechanism of TED-PAs and optimize their configuration and applied voltage. In this study, we obtained the discharge photograph, the thrust, and the flow velocity field and investigated the characteristics of the DC voltage and the frequency of the AC voltage. To isolate the effects of the discharge from the potential variation, a corona discharge plasma actuator and a TED-PA were compared. As a result, increasing the frequency of the AC voltage induced stronger jets from the AC and DC electrodes. This result indicates that the barrier discharge enhances the jet from the DC electrode without changing the potential difference between the electrodes.