Jeet P. Patil
Research Subjects
Jeet P. Patil has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Peeyush Mahajan
4 shared publicationsSushil Mishra
4 shared publicationsSushil K. Mishra
3 shared publicationsJitesh Vasavada
Department of Mechanical Engineering, IIT Bombay, Mumbai, India
2 shared publications- Sushil Mishra
Department of Mechanical Engineering, Indian Institute of Technology Bombay, Mumbai, India
2 shared publications - A. H. Siddiqui
Department of Mechanical Engineering, Indian Institute of Technology Bombay, Mumbai, India
1 shared publication
Latest Publications
- 14 February 2025
- Published by Elsevier in Materials Letters
- Vol. 386
A novel approach to enhance formability of thin SS304 foils via multi-stage micro-incremental forming
- 14 February 2025
- Published by Elsevier in Materials Letters
- Vol. 386
A novel approach to enhance formability of thin SS304 foils via multi-stage micro-incremental forming
- 2 December 2024
- Published by Elsevier in Materials Letters
- Vol. 382
Phase transformation and texture evolution during micro-incremental forming of ultra-thin SS316 sheets
- 2 December 2024
- Published by Elsevier in Materials Letters
- Vol. 382
Phase transformation and texture evolution during micro-incremental forming of ultra-thin SS316 sheets
- 30 May 2024
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 56 (5) , 652-660
Algorithm for sheet thickness measurement and its application to thermoformed PMMA sheet
One of the evaluative criteria utilized to ascertain the quality of a thermoformed product is the ultimate thickness of the sheet achieved through the processing. In determining the visual performance of optical products such as aircraft canopy, windscreens, etc., thickness distribution is crucial. Consequently, precise thickness measurement is the most essential aspect of quality control. To measure thickness, a variety of mechanical and optical measurement systems, in addition to several manual systems, are available. The manual intervention restricts the measurement system to lesser measurements and simplifies the system to simple geometries. Furthermore, post-processing of the image or point data is necessary to obtain thickness distribution using an optical measurement system. However, manual intervention is exceptionally time-consuming and may result in inaccurate outcomes. As a result, the current investigation put forth an algorithm based on machine learning to measure the precise thickness distributions from point data obtained through the measuring system. The algorithm’s functionality is illustrated through the thermoforming of a PMMA hemispherical dome at various forming pressures. Point data for thickness measurements of the hemispherical domes were acquired using the Rapid-I system of measurement. Utilizing the proposed algorithm, the thickness distribution of the hemispherical domes was measured accurately and efficiently.
- 30 May 2024
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 56 (5) , 652-660
Algorithm for sheet thickness measurement and its application to thermoformed PMMA sheet
One of the evaluative criteria utilized to ascertain the quality of a thermoformed product is the ultimate thickness of the sheet achieved through the processing. In determining the visual performance of optical products such as aircraft canopy, windscreens, etc., thickness distribution is crucial. Consequently, precise thickness measurement is the most essential aspect of quality control. To measure thickness, a variety of mechanical and optical measurement systems, in addition to several manual systems, are available. The manual intervention restricts the measurement system to lesser measurements and simplifies the system to simple geometries. Furthermore, post-processing of the image or point data is necessary to obtain thickness distribution using an optical measurement system. However, manual intervention is exceptionally time-consuming and may result in inaccurate outcomes. As a result, the current investigation put forth an algorithm based on machine learning to measure the precise thickness distributions from point data obtained through the measuring system. The algorithm’s functionality is illustrated through the thermoforming of a PMMA hemispherical dome at various forming pressures. Point data for thickness measurements of the hemispherical domes were acquired using the Rapid-I system of measurement. Utilizing the proposed algorithm, the thickness distribution of the hemispherical domes was measured accurately and efficiently.
- 3 April 2023
- Published by Springer Nature in Experimental Mechanics
- Vol. 63 (5) , 853-869
Design of a Biaxial Cruciform Specimen with a High Degree of Plastic Deformation and Yield Locus Evolution
- 3 April 2023
- Published by Springer Nature in Experimental Mechanics
- Vol. 63 (5) , 853-869
Design of a Biaxial Cruciform Specimen with a High Degree of Plastic Deformation and Yield Locus Evolution
- 28 November 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 202
Microstructure engineering during directed energy deposition of Al-0.5Sc-0.5Si using heated build platform
- 28 November 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 202
Microstructure engineering during directed energy deposition of Al-0.5Sc-0.5Si using heated build platform
- 31 October 2022
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (1) , 3-13
Effect of hyperelastic pre-stretching on thickness distribution of pressure thermoformed products
Pressure thermoforming is one of the most used processes, but the thickness gradient in the formed parts limits its application. To control the product thickness distribution, pressure forming is assisted by a punch. However, due to punch contact with the sheet, the process is susceptible to surface defect, which is detrimental to the optical properties of the product. To produce optical parts with zero surface defects and controlled thickness distribution, a novel approach as a means for dimensional control by sheet pre-stretching is proposed and validated numerically. It was found that pre-stretching has a significant effect on the deformation behavior of the product.
- 31 October 2022
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (1) , 3-13
Effect of hyperelastic pre-stretching on thickness distribution of pressure thermoformed products
Pressure thermoforming is one of the most used processes, but the thickness gradient in the formed parts limits its application. To control the product thickness distribution, pressure forming is assisted by a punch. However, due to punch contact with the sheet, the process is susceptible to surface defect, which is detrimental to the optical properties of the product. To produce optical parts with zero surface defects and controlled thickness distribution, a novel approach as a means for dimensional control by sheet pre-stretching is proposed and validated numerically. It was found that pre-stretching has a significant effect on the deformation behavior of the product.
- 27 January 2022
- Published by ASTM International in Materials Performance and Characterization
- Vol. 11 (2) , 53-87
A Review on the Material Development and Corresponding Properties for Power Plant Applications
Over the past decade, increased demand for energy generation at affordable rates and in a clean state has been the driving force for material development for energy generation. In developing countries, coal-fired thermal power plants are the major source of electricity generation. However, coal-fired plants induce a higher carbon footprint and contribute to greenhouse gas emissions. Hence, several strategies have been formulated to mitigate environmental pollution while maintaining high energy output. This review comprehensively presents the historical material development process that led to an increase in the efficiency of a coal-fired power plant. Candidate material identification and application, essential alloying elements, and their impact on service life are comprehensively reviewed. Adapting the ultra-supercritical (USC) and advanced ultra-supercritical (A-USC) power generation technology requires the development of new alloys that can withstand harsh operating conditions (700–725°C and 25–35 MPa), which demands the replacement of conventional materials (ferritic/austenitic steel) with better ones. The candidate alloys should be evaluated across several key issues such as high-temperature material response to loading, creep strength, high-temperature oxidation, and component fabricability. The evaluation of creep strength data suggests that nickel-based alloys like Inconel alloy 282 are preferred because of the high stability of the γ′ phase. Moreover, at higher temperatures, nickel-based alloys are preferred over ferritic/austenitic steel alloys because of their superior corrosion resistance. The fireside corrosion and high-temperature oxidation resistance are governed by the formation of different oxide layers depending on the temperature, pressure, and alloy content. Furthermore, the weldability of different candidate alloys is discussed in detail, along with the microstructural evolution in the heat-affected zone. This review also focuses on the cost of constructing a greenfield USC/A-USC power plant. Lastly, a perspective on new alloy development for A-USC/USC application is presented, and the microstructure and property relationships of these alloys are discussed.
- 27 January 2022
- Published by ASTM International in Materials Performance and Characterization
- Vol. 11 (2) , 53-87
A Review on the Material Development and Corresponding Properties for Power Plant Applications
Over the past decade, increased demand for energy generation at affordable rates and in a clean state has been the driving force for material development for energy generation. In developing countries, coal-fired thermal power plants are the major source of electricity generation. However, coal-fired plants induce a higher carbon footprint and contribute to greenhouse gas emissions. Hence, several strategies have been formulated to mitigate environmental pollution while maintaining high energy output. This review comprehensively presents the historical material development process that led to an increase in the efficiency of a coal-fired power plant. Candidate material identification and application, essential alloying elements, and their impact on service life are comprehensively reviewed. Adapting the ultra-supercritical (USC) and advanced ultra-supercritical (A-USC) power generation technology requires the development of new alloys that can withstand harsh operating conditions (700–725°C and 25–35 MPa), which demands the replacement of conventional materials (ferritic/austenitic steel) with better ones. The candidate alloys should be evaluated across several key issues such as high-temperature material response to loading, creep strength, high-temperature oxidation, and component fabricability. The evaluation of creep strength data suggests that nickel-based alloys like Inconel alloy 282 are preferred because of the high stability of the γ′ phase. Moreover, at higher temperatures, nickel-based alloys are preferred over ferritic/austenitic steel alloys because of their superior corrosion resistance. The fireside corrosion and high-temperature oxidation resistance are governed by the formation of different oxide layers depending on the temperature, pressure, and alloy content. Furthermore, the weldability of different candidate alloys is discussed in detail, along with the microstructural evolution in the heat-affected zone. This review also focuses on the cost of constructing a greenfield USC/A-USC power plant. Lastly, a perspective on new alloy development for A-USC/USC application is presented, and the microstructure and property relationships of these alloys are discussed.
- 26 November 2020
- Published by Springer Nature
- p. 479-487
Effect of Sheet Temperature on Thickness Distribution of the Thermoformed Hemispherical Dome
- 26 November 2020
- Published by Springer Nature
- p. 479-487
Effect of Sheet Temperature on Thickness Distribution of the Thermoformed Hemispherical Dome