BXBowen Xu

Bowen Xu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bowen Xu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Patrick Teuffel

    Department of the Built Environment Eindhoven University of Technology Eindhoven MB The Netherlands

    4 shared publications
  • Rijk Blok

    Department of the Built Environment Eindhoven University of Technology Eindhoven MB The Netherlands

    4 shared publications
  • Bart van Den Hurk

    Department of the Built Environment Eindhoven University of Technology Eindhoven MB The Netherlands

    3 shared publications
  • Sean J. D. Lugger

    Department of Chemical Engineering and Chemistry Eindhoven University of Technology Eindhoven The Netherlands

    2 shared publications
  • Tao Liu

    Department of Environmental and Resource Engineering, Technical University of Denmark, 2400 Kgs. Lyngby, Denmark

    2 shared publications

Latest Publications

  • Open Access

    Effect of UV‐water weathering on the mechanical properties of flax‐fiber‐reinforced polymer composites

    by Bowen Xu, Bart van Den Hurk, Tao Liu, Rijk Blok, Patrick Teuffel

    This study examines the influence of weathering aging on the mechanical properties and durability of flax fiber‐reinforced polymer composites (FFRP) intended for outdoor applications. Employing an accelerated weathering environment replicating natural outdoor conditions, encompassing UV radiation, condensation, and water spray, the FFRP samples with 2 and 4 mm thicknesses underwent exposure durations of 0, 500, 1000, and 1500 h. Mechanical tests characterized tensile, flexural, and inner‐plane shear properties, while a custom‐made apparatus measured the long‐term tensile creep behavior. Additionally, scanning electron microscopy allowed for the observation of microscopic changes in fiber and matrix. The findings illustrate a consistent decline in tensile and flexural properties with increased weathering exposure, resulting in reductions of 17% and 38% in the tensile strength and modulus, and 24% and 52% in the flexural strength and modulus after 1500 h. Intriguingly, inner‐plane shear strength exhibited a slight increase after 500 h before a subsequent decrease. Furthermore, samples with the same thickness demonstrated an increased creep development with longer weathering durations. Despite this, the mechanical degradation rate induced by weathering was comparatively slower for thicker samples. Overall, the diminished mechanical properties of FFRP post‐weathering can be attributed not only to the polymer but also to the substantial role played by flax fibers in this process.Highlights: UV weathering degrades the mechanical properties of flax/polyester composites. Both the instantaneous elastic properties and the long‐term creep behavior are affected by weathering. Thickness influences the mechanical degradation of the composites caused by UV weathering. SEM confirmed UV‐water weathering resulted in the degradation of both natural fiber and polymer matrices.


  • Open Access

    Effect of environmental humidity on the creep behavior of flax fiber‐reinforced polymer composites

    by Bowen Xu, Bart van Den Hurk, Sean J. D. Lugger, Tao Liu, Rijk Blok, Patrick Teuffel

    Flax fiber‐reinforced polymer (FFRP) composites are emerging popular environmental‐friendly construction materials. However, their significant creep properties have been a major concern for using FFRP in load‐bearing structures. This article presents an investigation of the effect of environmental humidity on the creep behavior of the FFRP. Samples with flax fiber in 0°, 90°, and ± 45° were manufactured, respectively, by the vacuum infusion method. Accelerated creep tests were conducted on samples in different relative humidities (RH), and the results were analyzed by the time–temperature superposition principle (TTSP). It is found the creep development of samples with 0° and 90° fiber increases with the RH, and their 30‐year total strain in 97% RH is about 10 times higher than that in 11% RH. The samples with ±45° fiber are found not obviously sensitive to the humidity change. The scanning electron microscope (SEM) check indicates the change in the fiber–matrix interface and cracks between microfibrils in a fiber bundle is the main reason for the change of creep behavior in high humidity. This study may benefit the design of structures made of natural fiber‐reinforced polymer composites, especially for load‐bearing structures working in high‐humidity environments.


  • Open Access

    Creep analysis of the flax fiber-reinforced polymer composites based on the time–temperature superposition principle

    by Bowen Xu, Bart van Den Hurk, Sean J. D. Lugger, Rijk Blok, Patrick Teuffel

    Natural plant fiber-reinforced polymer composites (PFRP) have emerged as an environmental-friendly material in the construction industry, but their creep behavior is a critical concern for load-bearing structures. This study investigates the creep behavior of flax fiber-reinforced polymer composites (FFRP) using the time–temperature superposition principle (TTSP). Due to the application of TTSP on the tensile creep behavior of FFRP is not fully understood, three potential methods for calculating the critical parameters during TTSP are compared to obtain an efficient application method to build the creep master curve. A 2,000-h long-term creep test is conducted parallelly on the same sample to validate the accuracy of the creep analysis results. The study proposes an ideal method to determine the key parameters in TTSP, providing valuable insights for the practical application of PFRP in the construction industry. Meanwhile, the research results in this study would be helpful in better understanding the creep behavior of FFRP via short-term accelerated tests.