XWXinran Wang

Xinran Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xinran Wang has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhancing global charge reactivity in ammonia-diesel dual fuel engines through air pre-heating assist the intake diesel pre-injection strategy

    by Guangyuan Li, Run Chen, JiaYang Lv, Tie Li, Xinran Wang, Haoyun Shi, Shuai Huang, Shiyan Li, Fengnian Zhao, Fan Zhang, et al.

    Intake diesel pre-injection could enhance the global charge reactivity of low-pressure ammonia-diesel dual-fuel engines. However, wall wetting limits its effectiveness. In this study, intake air heating was coupled with intake diesel pre-injection to improve pre-injection diesel evaporation. The co-effects of intake temperature, engine load, ammonia energy ratio (AER), and pre-injection diesel energy ratio (PDER) on combustion and emission characteristics were experimentally investigated. At 45 °C intake temperature, 80AER and 80% PDER, the coefficient of variation of indicated mean effective pressure (CoVIMEP) exceeded 5% at 75% loads and below, whereas increasing the intake temperature to 135 °C reduced the CoVIMEP to approximately 3% even at 50% load. Besides, increasing the intake temperature produced a combustion-phasing advancement similar to decreasing AER and extends the stable operating boundary toward higher AER. However, the thermal-efficiency benefit of intake heating was governed by a trade-off between reduced unburned losses and increased wall heat transfer, the optimum intake temperatures increasing as engine load decreasing. Both intake temperature and engine load significantly altered the correspondence between indicated thermal efficiency and PDER. This highlights a strong coupling among thermodynamic conditions, PDER, and charge reactivity. Increasing PDER generally reduced CO2 emissions but increased N2O emissions, while unburned NH₃ exhibited a trend approximately opposite to that of indicated thermal efficiency. CO2-equivalent emissions increased with PDER at 75% load and below but decreased at full load. These findings demonstrate that intake temperature and PDER should be coordinated according to engine load to establish a load-adaptive charge-reactivity control framework.

  • Open Access

    Visualization of mechanical and thermal deicing processes in sea chest of seawater cooling system for ice-going ships

    by Zehao Wu, Yujin Cong, Xinran Wang, Qijun Ma, Ping Yi, Shuai Huang, Tie Li

    The operational safety of ice-going ships with stringent cooling demands critically depends on the unimpeded function of the seawater cooling system, which are highly susceptible to blockage risks by ice particles in polar regions. This study proposes an experimental methodology to investigate the mechanical and thermal deicing characteristics of a ship's seawater cooling system using a visualized and scaled sea-chest model based on an L-type deflector configuration. Normal and extreme ice blockage conditions are investigated to elucidate the transport, accumulation, and melting characteristics of ice particles. The impact of various hot reflux ratio and initiation timing on ice melting and blockage-prevention is systematically quantified through dynamic visualization and transient measurements. The results reveal that, a reflux ratio of 70% can provide an optimal balance between ice melting efficiency and suppression of ice particles escape into the outlet pipeline, which is a persistent issue with this design. Furthermore, initiating hot reflux can substantially increase the thermal melting efficiency and accelerate the temperature recovery for the sea chest system. The transient characteristics of the system are quantitatively evaluated using metrics such as pressure drop across the filters and outlet temperature evolutions, separately defined as the "ice blockage duration" and "unsteady state time". These findings provide the first quantitative experimental evidence and evaluation criteria for optimizing the hot reflux decing strategies for the seawater cooling system of ice-going ships.

  • Open Access

    A novel ammonia combustion concept enabled by high-pressure hydrogen jet ignition: Ignition, flame evolution, and emission characteristics

    by Shuai Huang, Weizhen Huang, Huimin Yang, Shiyan Li, Run Chen, Ping Yi, Fengnian Zhao, Xinran Wang, Tie Li

    Ammonia is a promising carbon-free fuel for internal combustion engines, yet its low flame speed and poor ignitability severely restrict practical application. To address these challenges, this study proposes a novel ammonia combustion mode based on in-cylinder high-pressure hydrogen direct injection coupled with spark-induced jet ignition. Compared with pre-chamber combustion systems, this approach offers superior stability and greater potential for achieving higher combustion efficiency, benefiting from advantages including multi-pulse ignition capability, pre-injection of hydrogen, stratified combustion, and avoidance of cold-start issues. A systematic experimental investigation is performed in a constant volume combustion vessel to comprehensively explore the combustion behaviors of premixed ammonia ignited by high-pressure hydrogen jet. Four key parameters are varied: hydrogen injection pressure (3.0-9.0 MPa), ammonia equivalence ratio (0-1.0), ignition timing (2.5/4.0 ms after start of injection), and ignition position (six axial/radial locations). Key findings reveal that ignition during hydrogen injection promotes flame kernel development over post-injection ignition, though positions away from nozzle/axis are required to avoid jet-induced extinction. Higher injection pressure enhances hydrogen supply and turbulence, accelerating early heat release. Lean ammonia mixtures benefit initial ignition via higher local oxygen, while late-stage performance is governed by ammonia concentration. Stoichiometric ammonia and higher pressure reduce unburned NH3. Notably, this novel mode achieves ~96% combustion efficiency when ammonia energy ratio of 99.3%. Further improvements in ammonia energy ratio and combustion efficiency could be expected in practical engines by adopting strategies such as early hydrogen injection and multi-stage injection.

  • Open Access

    A novel ammonia combustion mode using high-pressure hydrogen jet ignition: Optical experimental analysis

    by Shuai Huang, Weizhen Huang, Huimin Yang, Shiyan Li, Run Chen, Ping Yi, Fengnian Zhao, Xinran Wang, Tie Li

    Ammonia is a promising carbon-free fuel for internal combustion engines, yet its low flame speed and poor ignitability severely restrict practical application. To address these challenges, this study proposes a novel ammonia combustion mode based on in-cylinder high-pressure hydrogen direct injection coupled with spark-induced jet ignition. Compared with pre-chamber combustion systems, this approach offers superior stability and greater potential for achieving higher combustion efficiency, benefiting from advantages including multi-pulse ignition capability, pre-injection of hydrogen, stratified combustion, and avoidance of cold-start issues. A systematic experimental investigation is performed in a constant volume combustion vessel to comprehensively explore the combustion behaviors of premixed ammonia ignited by high-pressure hydrogen jet. Four key parameters are varied: hydrogen injection pressure (3.0-9.0 MPa), ammonia equivalence ratio (0-1.0), ignition timing (2.5/4.0 ms after start of injection), and ignition position (six axial/radial locations). Key findings reveal that ignition during hydrogen injection promotes flame kernel development over post-injection ignition, though positions away from nozzle/axis are required to avoid jet-induced extinction. Higher injection pressure enhances hydrogen supply and turbulence, accelerating early heat release. Lean ammonia mixtures benefit initial ignition via higher local oxygen, while late-stage performance is governed by ammonia concentration. Stoichiometric ammonia and higher pressure reduce unburned NH3. Notably, this novel mode achieves ~96% combustion efficiency when ammonia energy ratio of 99.3%. Further improvements in ammonia energy ratio and combustion efficiency could be expected in practical engines by adopting strategies such as early hydrogen injection and multi-stage injection.

  • A comparison between turbulent non-premixed jet flames of CH4 and the 50%NH3+50%H2 blend

    by Tie Li, Ning Wang, Zhifei Zhang, Xinyi Zhou, Xinran Wang, Run Chen, Shiyan Li, Ping Yi


  • Identification and Engineering of Post‐PKS Modification Bottlenecks for Ansamitocin P‐3 Titer Improvement in Actinosynnema pretiosum subsp. pretiosum ATCC 31280

    by Xinjuan Ning, Xinran Wang, Yuanting Wu, Qianjin Kang, Linquan Bai

    The type‐I polyketide ansamitocin P‐3 (AP‐3) is a potent antitumor agent. Its production is most likely hampered by the required multiple substrate supplies and complicated post‐PKS modifications in Actinosynnema pretiosum subsp. pretiosum ATCC 31280. For titer improvement, gene ansa30, encoding for a glycosyltransferase competing for the N‐demethyl‐AP‐3 (PND‐3) intermediate for AP‐3 biosynthesis, was initially inactivated. In the mutant NXJ‐22, the AP‐3 titer was increased by 66% along with an obvious accumulation of PND‐3, indicating that the N‐methylation is a rate‐limiting step. Alternatively, when abundant upstream intermediate 19‐chloroproansamitocin was fed into a PKS mutant, 3‐O‐acylation was further identified along with the N‐methylation as the rate‐limiting steps. Subsequent overexpression of N‐methyltransferase gene asm10 in NXJ‐22 resulted in a 93% increase of AP‐3 and a corresponding 92% decrease of PND‐3. Additional supplementation of L‐methionine, the precursor for SAM biosynthesis, substantially decreased the accumulation of PND‐3. In parallel, the 3‐O‐acylation bottleneck was relieved by feeding with L‐valine to NXJ‐22, resulting in a 126% increase of AP‐3. Eventually, a combined asm10 overexpression and supplementation of L‐methionine and L‐valine resulted in a 5‐fold increase of AP‐3, from 42 ± 2 mg L−1 to 246 ± 6 mg L−1, without any noticeable accumulation of PND‐3.