Minghan Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Minghan Li has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hong Jiang
State Key Laboratory of Tropic Ocean Engineering Materials and Materials Evaluation & Special Glass Key Laboratory of Hainan Province, Hainan University, Haikou 570228, China
2 shared publications - Yanping Ma
State Key Laboratory of Marine Resources Utilization in South China Sea, Hainan University, Haikou 570228, China
2 shared publications - Chunrong Xiong
State Key Laboratory of Marine Resources Utilization in South China Sea, Hainan University, Haikou 570228, China
1 shared publication - Jiaqi Duan
State Key Laboratory of Marine Resources Utilization in South China Sea & Special Glass Key Laboratory of Hainan Province, Hainan University, Haikou 570228, China
1 shared publication - Wenzhi Wang
State Key Laboratory of Marine Resources Utilization in South China Sea & Special Glass Key Lab of Hainan Province, Hainan University, Haikou 570228, China
1 shared publication - Ziming Huang
State Key Laboratory of Marine Resources Utilization in South China Sea & Special Glass Key Laboratory of Hainan Province, Hainan University, Haikou 570228, China
1 shared publication
Latest Publications
- Open Access
Preparation and Performance of Multilayer Si-B-C-N/Diamond-like Carbon Gradient Films
Si-B-C-N/diamond-like carbon (DLC) gradient films with different layers were prepared on a glass substrate by radio frequency magnetron sputtering, and the structure and surface morphology of the resulting films were analyzed by scanning electron microscopy, Raman spectrometry, and X-ray photoelectron spectroscopy. The mechanical and optical properties of the films were studied using a multifunctional material mechanical testing system, UV-Vis spectrophotometer, and micro-Vickers hardness tester. The gradient structure promotes the formation of sp3 bonds and improves the hardness and optical transmittance of the resulting films. Among the prepared films, the single-layer Si-B-C-N/DLC gradient film shows the highest optical transmittance (97%). Film–substrate adherence is strengthened by the introduction of the gradient structure. The best adhesion was obtained with a double-layer Si-B-C-N/DLC gradient film. Suitable anti-wear properties were exhibited in both dry (0.18) and wet (0.07) conditions. In this paper, evaluation of the microstructural, optical, and mechanical properties of the films could provide new insights into improvements in the bonding force of glass-based DLC films and enrich the experimental data of DLC multilayer film systems.
Open AccessPreparation and Performance of Multilayer Si-B-C-N/Diamond-like Carbon Gradient Films
Si-B-C-N/diamond-like carbon (DLC) gradient films with different layers were prepared on a glass substrate by radio frequency magnetron sputtering, and the structure and surface morphology of the resulting films were analyzed by scanning electron microscopy, Raman spectrometry, and X-ray photoelectron spectroscopy. The mechanical and optical properties of the films were studied using a multifunctional material mechanical testing system, UV-Vis spectrophotometer, and micro-Vickers hardness tester. The gradient structure promotes the formation of sp3 bonds and improves the hardness and optical transmittance of the resulting films. Among the prepared films, the single-layer Si-B-C-N/DLC gradient film shows the highest optical transmittance (97%). Film–substrate adherence is strengthened by the introduction of the gradient structure. The best adhesion was obtained with a double-layer Si-B-C-N/DLC gradient film. Suitable anti-wear properties were exhibited in both dry (0.18) and wet (0.07) conditions. In this paper, evaluation of the microstructural, optical, and mechanical properties of the films could provide new insights into improvements in the bonding force of glass-based DLC films and enrich the experimental data of DLC multilayer film systems.
- Open Access
Study on Crystallization Process of Li2O–Al2O3–SiO2 Glass-Ceramics Based on In Situ Analysis
In this paper, we used differential scanning calorimetry (DSC), high-temperature X-ray diffraction (HT-XRD), and confocal scanning laser microscopy (CSLM) to investigate the Li2O–Al2O3–SiO2 glass crystallization process. At 943 K, lithium disilicate (Li2Si2O5) phase crystals began to precipitate in the Li2O–Al2O3–SiO2 glass with a crystal size of 50–70 nm. At the temperature of 1009 K, petalite (LiAlSi4O10) crystals began to precipitate in the vitreous phase, forming composite spherical crystals of LiAlSi4O10 and Li2Si2O5 with size in the range of 90–130 nm. Furthermore, the Kissinger method and KAS method of the JMAK model were used to calculate the crystallization activation energy and the Avrami index “n”. It was found that the precipitation mechanism of the two kinds of crystals is whole crystallization; accordingly, the selection of crystallization heat treatment system was guided to determine the nucleation and crystallization temperature.
Open AccessStudy on Crystallization Process of Li2O–Al2O3–SiO2 Glass-Ceramics Based on In Situ Analysis
In this paper, we used differential scanning calorimetry (DSC), high-temperature X-ray diffraction (HT-XRD), and confocal scanning laser microscopy (CSLM) to investigate the Li2O–Al2O3–SiO2 glass crystallization process. At 943 K, lithium disilicate (Li2Si2O5) phase crystals began to precipitate in the Li2O–Al2O3–SiO2 glass with a crystal size of 50–70 nm. At the temperature of 1009 K, petalite (LiAlSi4O10) crystals began to precipitate in the vitreous phase, forming composite spherical crystals of LiAlSi4O10 and Li2Si2O5 with size in the range of 90–130 nm. Furthermore, the Kissinger method and KAS method of the JMAK model were used to calculate the crystallization activation energy and the Avrami index “n”. It was found that the precipitation mechanism of the two kinds of crystals is whole crystallization; accordingly, the selection of crystallization heat treatment system was guided to determine the nucleation and crystallization temperature.