Jiao-Yi Hou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jiao-Yi Hou has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Dayong Ning
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
2 shared publications Du Hongwei
National Center for International Research of Subsea Engineering Technology and Equipment, Dalian Maritime University, Dalian, China
1 shared publicationGong Yongjun
National Center for International Research of Subsea Engineering Technology and Equipment, Dalian Maritime University, Dalian, China
1 shared publicationHua Zhou
State Key Laboratory of Fluid Power Transmission and Control (Zhejiang University)
1 shared publication- Sun Hongyu
National Center for International Research of Subsea Engineering Technology and Equipment, Dalian Maritime University, Dalian, China
1 shared publication - Tingyu Geng
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
1 shared publication
Latest Publications
- Open Access
- 4 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (5) , 2754
Simulation and Experimental Research on Composite Diaphragm Hydraulic Force/Displacement Amplification Mechanism with Adjustable Initial Volume
To improve the practicability of electro-mechanical converters in hydraulic systems, especially in control valves, a hydraulic force/displacement amplification mechanism was addressed. The amplification mechanism includes a rolling diaphragm (RD) and a corrugated diaphragm (CD), and the amplification function is achieved using the area difference between the RD and the CD. To investigate the amplification characteristics of the mechanism, the diaphragm forces were analyzed by finite element simulations, and the dynamic model of the system was established in Simulink, based on the force balance method. Furthermore, an amplification mechanism prototype was fabricated, and the static and dynamic experiments were carried out. Combining the simulation and experiment results, the accuracy of the proposed dynamic model was verified, and the amplification characteristics of the amplification mechanism were analyzed. When the RD displacement is less than 2 mm, the force amplification effect is not obvious. When the RD displacement exceeds 2 mm, the force amplification ratio (FAR) increases with the RD displacement and decreases with the CD displacement. The maximum FAR is 2.5 with a CD displacement of 0 and an RD displacement of 6 mm. The amplification mechanism and the used research method are helpful for the application and control of the hydraulic valves.
- 4 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (5) , 2754
Open AccessSimulation and Experimental Research on Composite Diaphragm Hydraulic Force/Displacement Amplification Mechanism with Adjustable Initial Volume
To improve the practicability of electro-mechanical converters in hydraulic systems, especially in control valves, a hydraulic force/displacement amplification mechanism was addressed. The amplification mechanism includes a rolling diaphragm (RD) and a corrugated diaphragm (CD), and the amplification function is achieved using the area difference between the RD and the CD. To investigate the amplification characteristics of the mechanism, the diaphragm forces were analyzed by finite element simulations, and the dynamic model of the system was established in Simulink, based on the force balance method. Furthermore, an amplification mechanism prototype was fabricated, and the static and dynamic experiments were carried out. Combining the simulation and experiment results, the accuracy of the proposed dynamic model was verified, and the amplification characteristics of the amplification mechanism were analyzed. When the RD displacement is less than 2 mm, the force amplification effect is not obvious. When the RD displacement exceeds 2 mm, the force amplification ratio (FAR) increases with the RD displacement and decreases with the CD displacement. The maximum FAR is 2.5 with a CD displacement of 0 and an RD displacement of 6 mm. The amplification mechanism and the used research method are helpful for the application and control of the hydraulic valves.
- Open Access
- 21 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 37161-37172
Adaptive Noise Reduction Method of Synchronous Hydraulic Motor Acoustic Signal Based on Improved Dislocation Superposition Method
Acoustic signal contains information on the state of mechanical motion, but the disadvantage of low signal-to-noise ratio (SNR) is that acoustic signal without noise reduction is difficult to apply to fault diagnosis directly. This study proposes an adaptive noise reduction method based on the dislocation superposition method (DSM), which can realize automatic noise reduction for acoustic signals of low SNR synchronous hydraulic motors. First, the theoretical rotation period of the synchronous hydraulic motor is obtained according to the flow meter. Then, the actual signal is subjected to DSM processing according to the measurement accuracy of the flow meter and the theoretical rotation period to adjust the exact superposition length and the initial position of the actual signal. Finally, when the stop condition is not satisfied, the number of superposition is increased and the above process is repeated. The superimposed signal satisfying the stop condition is taken as the noise reduction signal. According to experimental results, the proposed method has good noise reduction effect on the acoustic signals of the synchronous hydraulic motor health state, wear out state of gear and end cover, and rust state of the gear. The noise reduction signal has been verified to have higher accuracy than the actual signal. Therefore, the proposed automatic noise reduction method can be applied to the noise reduction processing of other kinds of rotating mechanical acoustic signals.
- 21 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 37161-37172
Open AccessAdaptive Noise Reduction Method of Synchronous Hydraulic Motor Acoustic Signal Based on Improved Dislocation Superposition Method
Acoustic signal contains information on the state of mechanical motion, but the disadvantage of low signal-to-noise ratio (SNR) is that acoustic signal without noise reduction is difficult to apply to fault diagnosis directly. This study proposes an adaptive noise reduction method based on the dislocation superposition method (DSM), which can realize automatic noise reduction for acoustic signals of low SNR synchronous hydraulic motors. First, the theoretical rotation period of the synchronous hydraulic motor is obtained according to the flow meter. Then, the actual signal is subjected to DSM processing according to the measurement accuracy of the flow meter and the theoretical rotation period to adjust the exact superposition length and the initial position of the actual signal. Finally, when the stop condition is not satisfied, the number of superposition is increased and the above process is repeated. The superimposed signal satisfying the stop condition is taken as the noise reduction signal. According to experimental results, the proposed method has good noise reduction effect on the acoustic signals of the synchronous hydraulic motor health state, wear out state of gear and end cover, and rust state of the gear. The noise reduction signal has been verified to have higher accuracy than the actual signal. Therefore, the proposed automatic noise reduction method can be applied to the noise reduction processing of other kinds of rotating mechanical acoustic signals.
- 18 November 2012
- Published by Springer Nature in Journal of Central South University
- Vol. 19 (11) , 3110-3117
Model-based trajectory tracking control for an electrohydraulic lifting system with valve compensation strategy
- 18 November 2012
- Published by Springer Nature in Journal of Central South University
- Vol. 19 (11) , 3110-3117
Model-based trajectory tracking control for an electrohydraulic lifting system with valve compensation strategy