J. H. Swanson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
J. H. Swanson has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bernhard Auchmann
Paul Scherrer Institute, Villigen, Switzerland
1 shared publication - David Smekens
TE, CERN, Geneva Switzerland
1 shared publication - Diego Arbelaez
Lawrence Berkeley National Laboratory, Berkeley, CA, USA
1 shared publication - Friedrich Lackner
CERN, Geneva 23, Switzerland
1 shared publication - Giuseppe Montenero
PSI, Paul Scherrer Institut, Villigen, Switzerland
1 shared publication - Lucas Brouwer
Lawrence Berkeley National Laboratory
1 shared publication
Latest Publications
- 27 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Design of a High Toughness Epoxy for Superconducting Magnets and Its Key Properties
Nb $_3$ 3Sn accelerator magnets are poised to enable the luminosity upgrade of the Large Hadron Collider (LHC) at CERN, improving its potential for exploring physics beyond the standard model of particle physics. The prototype Nb3Sn magnets consistently need 10-25 quenches to achieve their best performance. A hypothesis is that the long training of these magnets may at least be partially induced by epoxy cracking and bonding failures. In 2018, we showed that several existing epoxies have a higher toughness and less tendency to crack at low temperatures than CTD-101K, the epoxy resin with which almost all Nb3Sn accelerator magnets have been impregnated. Here we explore a new high toughness formulation for reducing quench training of Nb3Sn accelerator magnets, through combining two amine curing agents to achieve a good glass transition temperature (Tg), adding a viscosity reducer to achieve low viscosity, and experimenting a coupling agent for improved bonding strengths. We report results of comprehensive materials tests, including thermal shock, tensile, compressive, shear tests, viscosity and Tg tests.- 27 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Design of a High Toughness Epoxy for Superconducting Magnets and Its Key Properties
Nb $_3$ 3Sn accelerator magnets are poised to enable the luminosity upgrade of the Large Hadron Collider (LHC) at CERN, improving its potential for exploring physics beyond the standard model of particle physics. The prototype Nb3Sn magnets consistently need 10-25 quenches to achieve their best performance. A hypothesis is that the long training of these magnets may at least be partially induced by epoxy cracking and bonding failures. In 2018, we showed that several existing epoxies have a higher toughness and less tendency to crack at low temperatures than CTD-101K, the epoxy resin with which almost all Nb3Sn accelerator magnets have been impregnated. Here we explore a new high toughness formulation for reducing quench training of Nb3Sn accelerator magnets, through combining two amine curing agents to achieve a good glass transition temperature (Tg), adding a viscosity reducer to achieve low viscosity, and experimenting a coupling agent for improved bonding strengths. We report results of comprehensive materials tests, including thermal shock, tensile, compressive, shear tests, viscosity and Tg tests.- 4 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-6
Coil Manufacturing Process of the First 1-m-Long Canted–Cosine–Theta (CCT) Model Magnet at PSI
At PSI the Canted-Cosine-Theta (CCT) magnet program aims at demonstrating that CCT technology is a viable candidate for the development of 16-T dipole magnets, required for future circular colliders. The first step in this direction is the implementation of a Nb3Sn 1-m-long, 2-layer CCT single-aperture dipole, referred to as Canted Dipole One (CD1) which is designed to achieve a peak field in the bore of ~11 T. The in-house manufacturing and assembly of CD1 requires to set up at PSI the infrastructure for a number of fabrication steps. In this paper, the authors review the coil manufacturing process of Nb3Sn CCT model magnets at PSI and describe the related commissioning phase.
- 4 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-6
Coil Manufacturing Process of the First 1-m-Long Canted–Cosine–Theta (CCT) Model Magnet at PSI
At PSI the Canted-Cosine-Theta (CCT) magnet program aims at demonstrating that CCT technology is a viable candidate for the development of 16-T dipole magnets, required for future circular colliders. The first step in this direction is the implementation of a Nb3Sn 1-m-long, 2-layer CCT single-aperture dipole, referred to as Canted Dipole One (CD1) which is designed to achieve a peak field in the bore of ~11 T. The in-house manufacturing and assembly of CD1 requires to set up at PSI the infrastructure for a number of fabrication steps. In this paper, the authors review the coil manufacturing process of Nb3Sn CCT model magnets at PSI and describe the related commissioning phase.