Habib Benzaama
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Habib Benzaama has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Mokhtari
Laboratory LaRTFM, Department of Mechanical Engineering, Ecole Nationale Polytechnique d’Oran Maurice Audin
4 shared publications - Elamine Abdelouahed
LABAB Laboratory, Mechanical Engineering, National Polytechnic School of Oran Maurice Audin, Oran, Algeria
3 shared publications - Mohammed Bentahar
Faculty of Technology Department of Civil Engineering and Hydraulics University of Saida Dr. Moulay Tahar Saida People's Democratic Republic of Algeria
2 shared publications - Abdallah Benzaama
Ecole Nationale Polytechnique d'Oran Maurice Audin
1 shared publication - Abdelaziz Ahmed-Bensoltane
LABAB Laboratory, Mechanical Engineering, National Polytechnic School of Oran Maurice Audin, Oran, Algeria
1 shared publication - Amir Slamen
National Polytechnic School of Oran M.A., ENPO, LABAB Laboratory, Oran, Algeria
1 shared publication
Latest Publications
- 18 November 2022
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 23 (1) , 316-330
Using XFEM Technique to Predict the Effect of Default on the Damage of Steel Pipe Reduced-Connection Under Bending and Pressure Loading
- 18 November 2022
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 23 (1) , 316-330
Using XFEM Technique to Predict the Effect of Default on the Damage of Steel Pipe Reduced-Connection Under Bending and Pressure Loading
- Open Access
- 22 June 2021
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 15 (57) , 182-194
Numerical modeling of the contact effect on the parameters of cracking in a 2D Fatigue Fretting Model
The objective of this work is to study the effects of contact parameters on the cracking parameters of a specimen and a pad assembly. These parameters have been studied and evaluated by the finite element method analysis in two dimensions fretting fatigue model through the Abaqus calculation code. Different values of the coefficient of friction of 0.1, 0.3 and 0.6 were applied on the various lengths in contact for a = 0.1, 0.5 and 1mm. Thus, on the various values of angle of orientation of the crack equal to 15 °, 30 ° and 45 °. In addition, elements of the type (CPE4R) and the criterion of maximum tangential stress were applied. The curves of the crack parameters such as the SIF coefficients and the integral J were obtained and discussed.
- 22 June 2021
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 15 (57) , 182-194
Open AccessNumerical modeling of the contact effect on the parameters of cracking in a 2D Fatigue Fretting Model
The objective of this work is to study the effects of contact parameters on the cracking parameters of a specimen and a pad assembly. These parameters have been studied and evaluated by the finite element method analysis in two dimensions fretting fatigue model through the Abaqus calculation code. Different values of the coefficient of friction of 0.1, 0.3 and 0.6 were applied on the various lengths in contact for a = 0.1, 0.5 and 1mm. Thus, on the various values of angle of orientation of the crack equal to 15 °, 30 ° and 45 °. In addition, elements of the type (CPE4R) and the criterion of maximum tangential stress were applied. The curves of the crack parameters such as the SIF coefficients and the integral J were obtained and discussed.
- Open Access
- 10 August 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (50) , 184-193
Using XFEM Techniques to Predict the Damage of aluminum 2024T3 notched under tensile load
The objective of this work is to analyze some geometrical effect to predict the damage of aluminum 2024T3 structure after validate numerical model by experimental test. The mechanical of damage behaviour under tensile tests of several plates with notches of various forms are investigated using an XFEM technique. The finite element analysis is performed to determine the failure load of these plates. Four different form of notched plates in another part of this work are reinforced by a thickness augmentation with different shapes around the notch. The results of the tensile analysis show that the reinforcements gives the best increase in failure load of each plates.
- 10 August 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (50) , 184-193
Open AccessUsing XFEM Techniques to Predict the Damage of aluminum 2024T3 notched under tensile load
The objective of this work is to analyze some geometrical effect to predict the damage of aluminum 2024T3 structure after validate numerical model by experimental test. The mechanical of damage behaviour under tensile tests of several plates with notches of various forms are investigated using an XFEM technique. The finite element analysis is performed to determine the failure load of these plates. Four different form of notched plates in another part of this work are reinforced by a thickness augmentation with different shapes around the notch. The results of the tensile analysis show that the reinforcements gives the best increase in failure load of each plates.
- Open Access
- 24 June 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (49) , 698-713
Finite Element Analysis of the thermo-Mechanical Behavior of composite Pipe Elbows under Bending and Pressure loading
Elbows under load experience more stress and strain than straight tubes. The strength of the composite tubes plays an important role in their use, the damage under a thermomechanical behavior of a composite tubular structure bent between two linear parts is studied in this work. The HASCHIN criterion model is used through finite element analysis. The main objective is to predict the effect of the main parameters by curves of torque, using the calculation code ABAQUS. These evaluative parameters are addressed to the geometrical conditions of the elbow, in loading mode on the pressurized structures and to the danger of the defect, hence the advantage of using Shell elements as a structure. The numerical results obtained illustrate that the parameters studied condition the level and the mode of failure as well as the response of composite elbows.
- 24 June 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (49) , 698-713
Open AccessFinite Element Analysis of the thermo-Mechanical Behavior of composite Pipe Elbows under Bending and Pressure loading
Elbows under load experience more stress and strain than straight tubes. The strength of the composite tubes plays an important role in their use, the damage under a thermomechanical behavior of a composite tubular structure bent between two linear parts is studied in this work. The HASCHIN criterion model is used through finite element analysis. The main objective is to predict the effect of the main parameters by curves of torque, using the calculation code ABAQUS. These evaluative parameters are addressed to the geometrical conditions of the elbow, in loading mode on the pressurized structures and to the danger of the defect, hence the advantage of using Shell elements as a structure. The numerical results obtained illustrate that the parameters studied condition the level and the mode of failure as well as the response of composite elbows.
- Open Access
- 15 October 2017
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 55 (4) , 1257-1268
Effects of the composite stacking sequence on the failure load of the single lap bonded joint
Effects of the composite stacking sequence on the failure load of the single lap bonded joint
- 15 October 2017
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 55 (4) , 1257-1268
Open AccessEffects of the composite stacking sequence on the failure load of the single lap bonded joint
Effects of the composite stacking sequence on the failure load of the single lap bonded joint
- Open Access
- 15 July 2017
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 55 (3) , 869-881
A new automated stretching finite element method for 2D crack propagation
This work presents a study of crack propagation with a new 2D finite element method with the stretching of the mesh. This method affects at each propagation step new coordinates of each element node of the mesh. The structure is divided to areas and each area has its own coordinate formulas. A program in FORTRAN allows us to create a parametric mesh, which keeps the same number of nodes and elements during different steps of crack propagation. The nodes are stretched using the criterion of maximum circumferential stress (MCS). The fracture parameters such as stress intensity factors in modes I and II and the orientation angles are calculated by solving the problem by the finite element code ABAQUS.
- 15 July 2017
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 55 (3) , 869-881
Open AccessA new automated stretching finite element method for 2D crack propagation
This work presents a study of crack propagation with a new 2D finite element method with the stretching of the mesh. This method affects at each propagation step new coordinates of each element node of the mesh. The structure is divided to areas and each area has its own coordinate formulas. A program in FORTRAN allows us to create a parametric mesh, which keeps the same number of nodes and elements during different steps of crack propagation. The nodes are stretched using the criterion of maximum circumferential stress (MCS). The fracture parameters such as stress intensity factors in modes I and II and the orientation angles are calculated by solving the problem by the finite element code ABAQUS.