MBMohammed Bentahar

Mohammed Bentahar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammed Bentahar has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mechanical, thermal and interfacial performance of sustainable polypropylene hybrid composites reinforced with short woven hemp fibers, basalt fibers and wheat straw ash

    by Abdelkader Daikh, Noureddine Mahmoudi, Mohammed Bentahar

    The growing demand for sustainable lightweight materials has encouraged the development of hybrid polymer composites reinforced with natural fibers and agricultural waste. In this study, polypropylene (PP) hybrid composites reinforced with short woven hemp fibers (SWHFs), chopped basalt fibers (BFs), wheat straw ash (WSA), and maleic anhydride-grafted PP (MAPP) were developed and systematically investigated. The experimental program was conducted in two stages. First, the BF content was optimized by incorporating 5–25 wt.% BF into PP containing 25 wt.% SWHF. The optimized formulation was then modified by adding 6, 12, and 18 wt.% WSA with a constant MAPP content. The composites were fabricated by twin-screw extrusion followed by injection molding and characterized using tensile and flexural tests, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). Incorporation of 20 wt.% BF increased the tensile strength and modulus of the hemp fiber-reinforced PP composite by approximately 21% and 94% (from 35.62 to 43.00 MPa and 1.80–3.50 GPa, respectively), together with 30% and 50% increases in flexural strength and modulus (56.48–73.28 MPa and 2.42–3.62 GPa). Incorporation of WSA further increased tensile and flexural modulus by up to 41% and 55% relative to the BF-optimized composite, while MAPP addition raised tensile strength by up to 27% (43.00–54.50 MPa), consistent with improved matrix-reinforcement compatibility. SEM revealed fewer visible interfacial voids in the examined regions of the MAPP-containing composites, and FTIR revealed spectral changes consistent with modified interfacial interactions between the constituents without direct evidence of new covalent-bond formation. TGA showed that the residual char yield increased from 0.20% for neat PP to 13.83% after BF incorporation and up to 16.0% for the WSA/MAPP-modified composites, indicating an increased thermally stable residual fraction. Among the WSA-modified formulations, the 6 wt.% WSA composite exhibited the highest tensile and flexural strength (54.50 and 86.40 MPa, respectively), whereas the 12 wt.% WSA composite provided marginally higher tensile and flexural moduli (4.94 and 5.62 GPa) together with a more balanced thermal response; the latter (25SWHF/20BF/PP-6MAPP-12WSA) is therefore identified as the formulation offering the best overall property balance rather than the single highest-strength composition. These findings demonstrate the potential of WSA as a sustainable inorganic functional filler for high-performance PP hybrid composites.

  • Open Access

    Fatigue crack propagation modeling in 2D structures using the CPCN-FEM node-based approach

    by Bentahar Mohammed, Mahmoudi Noureddine, Hachemi Nedir, Arbi Moulai

    Introduction/purpose: The study aims to model fatigue-related crack propagation by introducing a numerical method, CPCN-FEM (Crack Propagation by Coordinates of Nodes - Finite Element Method), which predicts crack trajectories through the systematic generation of nodal coordinates around the crack front. Methods: The approach defines four principal nodes to control the propagation direction and computes the stress intensity factors (K I) and (KII), along with the crack inclination angle (β). The method was implemented in FORTRAN to automate node tracking, coordinate updating, and stepwise crack advance in a two-dimensional elastic isotropic model. Simulations were conducted and compared with analytical crack-path solutions, using the Richard criterion to determine crack orientation. Results: The numerical model reproduced expected crack trajectories with high agreement with analytical predictions and demonstrated stable displacement behavior across multiple propagation cases. Mesh integrity was preserved during all propagation steps, and no remeshing was required. Conclusion: The findings show that CPCN-FEM provides an accurate, efficient, and mesh-preserving technique for modeling crack growth under fatigue, offering reliable predictions of crack path evolution in fracture mechanics.

  • Open Access

    Numerical optimization by the PFEMCT-SIF method of the crack propagation of a linear elastic material

    by Mohammed Bentahar, Noureddine Mahmoudi, Arbi Youcef Moulai

    Introduction/purpose: This study investigates the influence of contour numbers surrounding the crack tip on stress intensity factors (SIFs) using the Propagation Finite Element Method Crack Tip Stress Intensity Factor (PFEMCT-SIF) approach. It also compares the maximum circumferential stress criterion (MCSC) and the Richard criterion for crack propagation prediction. Methods: A finite element code written in Visual Fortran was developed to model crack tips with 3, 5, 10, 15 and 20 contours using 4-node quadratic CPE4 elements. Abaqus software was utilized to calculate SIFs and crack orientation angles. Horizontal and inclined cracks were analyzed in a steel plate under tensile loading. The results were validated against analytical solutions and previous numerical studies. Results: The 10-contour model showed the best agreement with analytical SIF values. Increasing contour numbers improved SIF accuracy for horizontal cracks, but excessive refinement led to divergence for inclined cracks. The MCSC and the Richard criterion produced comparable crack trajectories, with the MCSC demonstrating slightly higher precision. Conclusions: The PFEMCT-SIF method effectively evaluates SIFs and predicts crack propagation paths. A 10-contour crack tip model balances accuracy and computational efficiency. The study highlights the importance of optimizing crack tip mesh refinement in fracture mechanics simulations.


  • Open Access

    Characterization of high-performance composite bricks fabricated from recycled HDPE/PS blends and brick powder

    by Youcef Seif Eddine Moulai Arbi, Mohammed Bentahar, Noureddine Mahmoudi

    This study explores the feasibility and benefits of utilizing plastic waste in the production of construction materials, specifically composite bricks. The escalating accumulation of plastic waste poses significant environmental challenges, which necessitates innovative approaches for recycling and re-utilization to mitigate pollution and reduce landfill use. Our research focuses on the synthesis of bricks by incorporating high-density polyethylene (HDPE) and polystyrene (PS) with sand brick powder, utilizing a compatibilizer (SBS-g-MA) to enhance interfacial adhesion and mechanical integrity. The experimental methodology involved the preparation of composite materials through melt mixing, followed by molding to form brick specimens. These were analyzed for their mechanical properties, including tensile strength, Young’s modulus, and elongation at break, as well as thermal properties such as degradation temperature and crystallization behavior. Results showed that the inclusion of sand brick powder significantly enhances the thermal stability of the composites, as evidenced by the higher degradation temperatures observed. Specifically, the degradation temperature increased from 300.59 °C in pure HDPE/PS blends to 420.39 °C in composites with 7% brick powder, suggesting the formation of a protective barrier against thermal decomposition. Moreover, mechanical testing revealed that composites with up to 7% brick powder exhibited improved tensile strength and Young’s modulus compared to pure polymer blends.


  • Open Access

    Design and performance of a manual extruder for recycled plastic-brick composite pavers

    by Abdelkader Daikh, Arbi Moulai, Mohammed Bentahar, Noureddine Mahmoudi

    Introduction/purpose: This study aimed to develop a cost-effective manual plastic brick extruder for manufacturing composite bricks from recycled polypropylene and brick powder. The goal was to address housing challenges in developing countries while promoting sustainable waste management. Methods: A single screw extruder with a 60 mm die was fabricated, featuring a manual crank, a heating system, and a hopper. Composite specimens with varying polypropylene (30-80 weight percentages) and brick powder (20-70 weight percentages) ratios were produced. Mechanical testing was conducted, including compressive strength, flexural strength, impact resistance, and density measurements. Results: The 40:60 polypropylene:brick powder mixture exhibited optimal compressive strength, ranging from 23.76-24.90 MPa. Flexural strength peaked at the 50:50 ratio (11.86-12.5 MPa). Impact resistance decreased with increasing brick powder content. Density increased linearly with brick powder content, ranging from 1.48-1.77 g/cm³. The extruder successfully produced uniform composite specimens across all mixtures. Conclusions: The study demonstrated the feasibility of producing composite bricks using a low-cost, manually operated extruder. Two optimal mixture compositions were identified: 40:60 polypropylene:brick powder for maximum compressive strength and 50:50 for optimal flexural strength. This approach offers a promising solution for affordable housing construction while addressing plastic waste management in developing regions. Future research should focus on optimizing the extrusion process, exploring additional waste materials, and conducting long-term durability studies of composite bricks.


  • Open Access

    Evaluating the structural performance of masonry walls incorporating recycled plastic bricks under monotonic and cyclic loading

    by Arbi Youcef Moulai, Noureddine Mahmoudi, Mohammed Bentahar

    Introduction/purpose: This study evaluates the structural performance of masonry walls made from recycled plastic bricks under monotonic and cyclic loading. The purpose was to investigate the feasibility of using recycled plastic bricks as an alternative for masonry construction, focusing on their structural viability and potential environmental benefits. Methods: A simplified micro-modeling approach in Abaqus was employed to simulate the behavior of these walls. The plastic bricks were represented with solid elements, while the mortar joints were modeled through cohesive interactions. The numerical model underwent validation through a mesh sensitivity analysis and was subjected to vertical compression followed by horizontal loading. Results: The findings indicated a reduction in strength compared to traditional masonry materials. However, the study successfully captured the structural response and damage evolution of masonry walls under the specified loading conditions. Despite the reduced strength, the structural viability of recycled plastic bricks was strongly affirmed, and the behavior observed under load conditions was particularly informative. Conclusions:The investigation underscored the potential of plastic composite bricks in contributing to sustainable building practices. The outcomes validated the feasibility of incorporating plastic bricks into construction, highlighting their environmental benefits and sustainable implications. This study advanced the field of sustainable construction materials by demonstrating the practical application and benefits of using recycled plastic bricks.


  • Open Access

    NUMERICAL MODELING OF THE CRACK PROPAGATION PARAMETERS OF TWO DIFFERENT ELEMENTS BY THE FEM METHOD

    by Mohammed Bentahar

    M. Bentahar, Numerical Modeling of the Crack Propagation Parameters of Two Different Elements by the FEM Method. Advanced Engineering Letters, 3(1), 2024:


  • Open Access

    Numerical study of a centred crack on an elastoplastic material by the FEM method

    by Mohammed Bentahar

    The numerical study of crack propagation is a very complex and important problem for knowing the lifetime of a structure. Nowadays, the modelling of crack propagation by various numerical methods plays a beneficial part in solving problems in fracture mechanics. Significantly used in biomechanics, biomaterials and structural calculation, it also makes it possible to deal with certain problems of fatigue of materials. In this article, a numerical study based on the finite element method (FEM) was used for a two-dimensional model, of an elastoplastic material, containing a central crack. The article is also based on the study of different cracking factors, such as stress intensity factors KI and KII, J-integral and strain energy. On the other hand, the contrast of these parameters was precisely centred on the five contours of the crack front. In addition, Abaqus computer code was used to obtain different results, moreover, CPS4R elements were used for modelling.


  • Open Access

    Numerical simulation of two-dimensional crack propagation using stretching finite element method by Abaqus

    by Mohammed Bentahar, Habib Benzaama

    Fatigue is a phenomenon that appears in items subjected to cyclic loads. Thus, rupture and partial oxidation are initiated from the beginning of the process. For this, the study of such a problem of material in fracture mechanics is based on the numerical analysis of the characteristics of a crack. In this article, we propose a modelling of crack propagation by a new method of stretching the mesh by 2D finite element in mixed mode, based on the creation of the elements through a program in the computer language Fortran. The parametric mesh with 4 nodes (CPE4) was created to make the simulation and to characterise the stress intensity factors, by the Abaqus computer code. For this, the validation of stretching finite element method (SFEM) results is done by other methods: extended finite element method (XFEM) and analytical method to simulate the crack propagation. The stress intensity factor (SIF) is an essential parameter of this study. Two possibilities for determining the SIF have been retained: one by the numerical method of our choice and the other by the analytical method. Parameters to characterise the stress state at the crack front KI and KII were evaluated in two stages one by the crack length and the other by the a/c ratio.


  • Open Access

    Numerical modeling of the contact effect on the parameters of cracking in a 2D Fatigue Fretting Model

    by Mohammed Bentahar, Habib Benzaama, Mahmoudi Noureddin

    The objective of this work is to study the effects of contact parameters on the cracking parameters of a specimen and a pad assembly. These parameters have been studied and evaluated by the finite element method analysis in two dimensions fretting fatigue model through the Abaqus calculation code. Different values ​​of the coefficient of friction of 0.1, 0.3 and 0.6 were applied on the various lengths in contact for a = 0.1, 0.5 and 1mm. Thus, on the various values ​​of angle of orientation of the crack equal to 15 °, 30 ° and 45 °. In addition, elements of the type (CPE4R) and the criterion of maximum tangential stress were applied. The curves of the crack parameters such as the SIF coefficients and the integral J were obtained and discussed.