Ahmad Rajabian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmad Rajabian has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Farshid Vahedifard
Department of Civil and Environmental Engineering Tufts University Medford MA USA
3 shared publications - Dov Leshchinsky
Univ. of Delaware
2 shared publications - Bhamidipati Venkata Surya Viswanadham
Indian Institute of Technology Bombay
1 shared publication - Mahmood Reza Shaghaghian
Department of Civil Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran
1 shared publication - Mustafa Karaman
Institute of Earth and Space Sciences, Eskisehir Technical University, Eskişehir, Turkey
1 shared publication - Nurhan Ecemis
Civil Engineering Department, Izmir Institute of Technology, Izmir, Turkey
1 shared publication
Latest Publications
- 8 July 2026
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 13 (6) , 205
Shaking Table Study on Liquefaction Resistance of Sand- Granulated Rubber Mixtures
- 8 July 2026
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 13 (6) , 205
Shaking Table Study on Liquefaction Resistance of Sand- Granulated Rubber Mixtures
- 1 June 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 150 (6) , 06024002
A Framework for Analyzing the Stability of Geosynthetic Reinforced Soil Walls under Unsaturated Conditions
Suction stress is one of the most significant factors affecting the serviceability and stability of soil structures. This study presents a framework for analyzing the stability of geosynthe...
- 1 June 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 150 (6) , 06024002
A Framework for Analyzing the Stability of Geosynthetic Reinforced Soil Walls under Unsaturated Conditions
Suction stress is one of the most significant factors affecting the serviceability and stability of soil structures. This study presents a framework for analyzing the stability of geosynthe...
- 5 March 2024
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 11 (4) , 2483-2500
Stability of Hillslopes with Compound Convex-Concave Profile Under Vertically Loaded Strip Footings
- 5 March 2024
- Published by Springer Nature in Transportation Infrastructure Geotechnology
- Vol. 11 (4) , 2483-2500
Stability of Hillslopes with Compound Convex-Concave Profile Under Vertically Loaded Strip Footings
- Open Access
- 22 June 2023
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 14 (1) , 1-16
Effect of initial failure geometry on the progress of a retrogressive seepage-induced landslide
Natural and man-made slopes can undergo a retrogressive landslide when subjected to seepage. Studying the mechanism of retrogressive landslides contributes greatly to the employment of effective mitigation approaches. A multi-stage limit equilibrium-based study was performed to explore how the geometry of initial failure affects the progress of a retrogressive, multiple-rotational landslide caused by seepage flow. Seepage-stability analyses were carried out on two silty sand slopes which were previously found to experience successive rotational failures upon raising the water table in centrifuge tests. Analyzed in prototype dimensions were the slope models with the height of 24 cm and inclinations of 45° (1V:1H) and 63.4° (2V:1H) tested at different centrifugal accelerations. According to the tests, the initial shallow failures were assumed to be circular initiating from the face and emerging from the toe of the slopes in the stability analyses. The impact of curvature and length of the initial failure surface (referred to as IFS) as well as the height of the scarp shaped at each failure episode were investigated. The results show that the landslide continues until the slope profile finds a stable curvature. For the landslides that occur in the 45° inclined slope, when the initial failure initiates at a higher elevation on the slope face, the landslide retrogresses further. In addition, with an increase in the length or curvature of IFS, the final retrogression distance decreases. Further, it was observed that the progress of landslides depends on the height of the scarp exposed at each failure episode.
- 22 June 2023
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 14 (1) , 1-16
Open AccessEffect of initial failure geometry on the progress of a retrogressive seepage-induced landslide
Natural and man-made slopes can undergo a retrogressive landslide when subjected to seepage. Studying the mechanism of retrogressive landslides contributes greatly to the employment of effective mitigation approaches. A multi-stage limit equilibrium-based study was performed to explore how the geometry of initial failure affects the progress of a retrogressive, multiple-rotational landslide caused by seepage flow. Seepage-stability analyses were carried out on two silty sand slopes which were previously found to experience successive rotational failures upon raising the water table in centrifuge tests. Analyzed in prototype dimensions were the slope models with the height of 24 cm and inclinations of 45° (1V:1H) and 63.4° (2V:1H) tested at different centrifugal accelerations. According to the tests, the initial shallow failures were assumed to be circular initiating from the face and emerging from the toe of the slopes in the stability analyses. The impact of curvature and length of the initial failure surface (referred to as IFS) as well as the height of the scarp shaped at each failure episode were investigated. The results show that the landslide continues until the slope profile finds a stable curvature. For the landslides that occur in the 45° inclined slope, when the initial failure initiates at a higher elevation on the slope face, the landslide retrogresses further. In addition, with an increase in the length or curvature of IFS, the final retrogression distance decreases. Further, it was observed that the progress of landslides depends on the height of the scarp exposed at each failure episode.
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 23 (2) , 04022278
Stability Analysis of Anchor-Reinforced Soil Slopes with Taylor’s Stability Chart
The stability of earth slopes can be enhanced by introducing an anchoring system. The factor of safety of an anchor-reinforced slope is one of the essential items required to evaluate stability. This parameter can be predicted using limit equilibrium and numerical approaches by relevant software. Taylor’s stability chart has been frequently used to estimate the factor of safety of an unreinforced homogeneous cohesive-frictional soil slope. An analytical expression was developed in this study based on the friction circle method by which the factor of safety of anchor-reinforced slopes can be predicted using Taylor’s chart. The anchor-reinforced slope considered in the analysis consisted of homogeneous cohesive-frictional soil. The analyses were carried out considering different slope inclinations, anchor loads, anchor orientations, and slip circles. An illustrative example explained the procedure for finding the factor of safety and showed how the developed method could be used by practicing engineers. A comparison between the factor of safety estimated by Taylor’s chart and the limit equilibrium method using SLIDE indicates a good agreement. An anchoring system can improve the stability of earth slopes. The safety factor of an anchor-reinforced slope is the most critical design parameter as it reflects whether the slope is stable against driving forces. In geotechnical engineering, the factor of safety can be computed using an analytical/numerical approach, based on which relevant commercial software programs have been developed. These software programs might not be available to everyone. More importantly, they often require parameters of soil that need complex tests to be found, making their use unattractive for practicing engineers. The factor of safety of plain slopes can be found using Taylor’s stability chart, which is widely used in practice due to being convenient. This study presents a method through which the factor of safety of each potential slip surface in an anchored reinforced slope can be determined using Taylor’s stability chart. According to the approach, an anchored slope is equalized with a plain slope having a greater value of internal soil friction angle. Then, the factor of safety of equalized plain slope is determined using Taylor’s stability chart.
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 23 (2) , 04022278
Stability Analysis of Anchor-Reinforced Soil Slopes with Taylor’s Stability Chart
The stability of earth slopes can be enhanced by introducing an anchoring system. The factor of safety of an anchor-reinforced slope is one of the essential items required to evaluate stability. This parameter can be predicted using limit equilibrium and numerical approaches by relevant software. Taylor’s stability chart has been frequently used to estimate the factor of safety of an unreinforced homogeneous cohesive-frictional soil slope. An analytical expression was developed in this study based on the friction circle method by which the factor of safety of anchor-reinforced slopes can be predicted using Taylor’s chart. The anchor-reinforced slope considered in the analysis consisted of homogeneous cohesive-frictional soil. The analyses were carried out considering different slope inclinations, anchor loads, anchor orientations, and slip circles. An illustrative example explained the procedure for finding the factor of safety and showed how the developed method could be used by practicing engineers. A comparison between the factor of safety estimated by Taylor’s chart and the limit equilibrium method using SLIDE indicates a good agreement. An anchoring system can improve the stability of earth slopes. The safety factor of an anchor-reinforced slope is the most critical design parameter as it reflects whether the slope is stable against driving forces. In geotechnical engineering, the factor of safety can be computed using an analytical/numerical approach, based on which relevant commercial software programs have been developed. These software programs might not be available to everyone. More importantly, they often require parameters of soil that need complex tests to be found, making their use unattractive for practicing engineers. The factor of safety of plain slopes can be found using Taylor’s stability chart, which is widely used in practice due to being convenient. This study presents a method through which the factor of safety of each potential slip surface in an anchored reinforced slope can be determined using Taylor’s stability chart. According to the approach, an anchored slope is equalized with a plain slope having a greater value of internal soil friction angle. Then, the factor of safety of equalized plain slope is determined using Taylor’s stability chart.
- 28 June 2022
- Published by Springer Nature in Indian Geotechnical Journal
- Vol. 52 (6) , 1313-1324
Centrifuge Study of a Retrogressive Seepage-Triggered Landslide in Silty Sand Slopes
- 28 June 2022
- Published by Springer Nature in Indian Geotechnical Journal
- Vol. 52 (6) , 1313-1324
Centrifuge Study of a Retrogressive Seepage-Triggered Landslide in Silty Sand Slopes