Steven M. Hues
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Steven M. Hues has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Elton Graugnard
Boise State University
4 shared publications - Jesse Wensel
Micron Technology 5 , 8000 S Federal Way, Boise, Idaho 83707
2 shared publications - John D. Hues
Micron School of Materials Science and Engineering, Boise State University 1 , 1910 University Drive, Boise, Idaho 83725
2 shared publications - Wesley Jen
Micron School of Materials Science and Engineering, Boise State University 1 , 1910 University Drive, Boise, Idaho 83725
2 shared publications - Anil U. Mane
Applied Materials Division, Argonne National Laboratory, Chicago, Illinois 60637, USA
1 shared publication - Arjan Singh
School of Electrical and Computer Engineering, Cornell University 3 , Ithaca, New York 14850
1 shared publication
Latest Publications
- 31 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (5)
Evolution of Raman and photoluminescence response in molybdenum disulfide thin films deposited via thermal atomic layer deposition
In order to enable further advances in microelectronics, new processes capable of precisely depositing films are required. This is especially true of processes meant for depositing two-dimensional (2D) transition metal dichalcogenides, such as MoS2, a material of particular interest due to its high potential mobility even at a thickness of a few atoms. In this work, we report industry-compatible processes for depositing crystalline MoS2 with a high degree of precision. We demonstrate the successful conversion of both MoOx and MoSx films deposited via thermal atomic layer deposition using bis(tert-butylimido)bis(dimethylamino)Mo(VI) and H2O or H2S, respectively, into crystalline MoS2 films after an anneal in H2S. The quality of the MoS2 films was assessed using Raman spectroscopy and photoluminescence (PL) response. We found that the intensity of the obtained PL spectra for MoSx:MoS2 films could be directly controlled as a function of cycle number, demonstrating a precise degree of process control. The physical characteristics of the crystalline MoS2 deposited using this process were further studied using industry-relevant structures, with the process demonstrating conformal MoS2 films deposited evenly throughout lateral trench structures with an aspect ratio of over 20:1. These results provide insight into methodologies for both precisely depositing and rapidly characterizing crystalline MoS2, which can accelerate the integration of 2D materials into leading edge microelectronics.
- 31 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (5)
Evolution of Raman and photoluminescence response in molybdenum disulfide thin films deposited via thermal atomic layer deposition
In order to enable further advances in microelectronics, new processes capable of precisely depositing films are required. This is especially true of processes meant for depositing two-dimensional (2D) transition metal dichalcogenides, such as MoS2, a material of particular interest due to its high potential mobility even at a thickness of a few atoms. In this work, we report industry-compatible processes for depositing crystalline MoS2 with a high degree of precision. We demonstrate the successful conversion of both MoOx and MoSx films deposited via thermal atomic layer deposition using bis(tert-butylimido)bis(dimethylamino)Mo(VI) and H2O or H2S, respectively, into crystalline MoS2 films after an anneal in H2S. The quality of the MoS2 films was assessed using Raman spectroscopy and photoluminescence (PL) response. We found that the intensity of the obtained PL spectra for MoSx:MoS2 films could be directly controlled as a function of cycle number, demonstrating a precise degree of process control. The physical characteristics of the crystalline MoS2 deposited using this process were further studied using industry-relevant structures, with the process demonstrating conformal MoS2 films deposited evenly throughout lateral trench structures with an aspect ratio of over 20:1. These results provide insight into methodologies for both precisely depositing and rapidly characterizing crystalline MoS2, which can accelerate the integration of 2D materials into leading edge microelectronics.
- Open Access
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Achieving 0.05 Ω-mm contact resistance in non-alloyed Ti/Au ohmics to β-Ga2O3 by removing surface carbon
Preserving a contamination-free metal–semiconductor interface in β-Ga2O3 is critical to achieve consistently low resistance (< 1 Ω-mm) ohmic contacts. Here, we report a scanning transmission electron microscopy study on the variation in Ti/Au ohmic contact quality to (010) β-Ga2O3 in a conventional lift-off vs a metal-first process. We observe a thin ∼1 nm carbon barrier between the Ti and Ga2O3 in a non-conductive contact fabricated by a conventional lift-off process, which we attribute to photoresist residue, not previously detected by x-ray photoelectron spectroscopy due to the thinness and patchy coverage of the carbon layer, as well as roughness of the Ga2O3 surface. This thin carbon barrier is confirmed by electron energy loss spectroscopy and atomic force microscopy-infrared spectroscopy. We believe that the presence of the thin and patchy carbon layer leads to the highly inconsistent contact behavior in previous reports on non-alloyed contacts. Adventitious carbon is also observed in a conductive ohmic contact metal-first processing on an as-grown sample. We find that a five minute active oxygen descum is sufficient to remove this carbon on as-grown samples, further improving the ohmic behavior and reducing the contact resistance Rc to 0.06 Ω-mm. We also show that an hour long UV-ozone treatment of the Ga2O3 surface can eliminate carbon residue from the lift-off processing, resulting in a low Rc of 0.05 Ω-mm.
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Open AccessAchieving 0.05 Ω-mm contact resistance in non-alloyed Ti/Au ohmics to β-Ga2O3 by removing surface carbon
Preserving a contamination-free metal–semiconductor interface in β-Ga2O3 is critical to achieve consistently low resistance (< 1 Ω-mm) ohmic contacts. Here, we report a scanning transmission electron microscopy study on the variation in Ti/Au ohmic contact quality to (010) β-Ga2O3 in a conventional lift-off vs a metal-first process. We observe a thin ∼1 nm carbon barrier between the Ti and Ga2O3 in a non-conductive contact fabricated by a conventional lift-off process, which we attribute to photoresist residue, not previously detected by x-ray photoelectron spectroscopy due to the thinness and patchy coverage of the carbon layer, as well as roughness of the Ga2O3 surface. This thin carbon barrier is confirmed by electron energy loss spectroscopy and atomic force microscopy-infrared spectroscopy. We believe that the presence of the thin and patchy carbon layer leads to the highly inconsistent contact behavior in previous reports on non-alloyed contacts. Adventitious carbon is also observed in a conductive ohmic contact metal-first processing on an as-grown sample. We find that a five minute active oxygen descum is sufficient to remove this carbon on as-grown samples, further improving the ohmic behavior and reducing the contact resistance Rc to 0.06 Ω-mm. We also show that an hour long UV-ozone treatment of the Ga2O3 surface can eliminate carbon residue from the lift-off processing, resulting in a low Rc of 0.05 Ω-mm.
- Open Access
- 30 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Intrinsic and atomic layer etching enhanced area-selective atomic layer deposition of molybdenum disulfide thin films
For continual scaling in microelectronics, new processes for precise high volume fabrication are required. Area-selective atomic layer deposition (ASALD) can provide an avenue for self-aligned material patterning and offers an approach to correct edge placement errors commonly found in top-down patterning processes. Two-dimensional transition metal dichalcogenides also offer great potential in scaled microelectronic devices due to their high mobilities and few-atom thickness. In this work, we report ASALD of MoS2 thin films by deposition with MoF6 and H2S precursor reactants. The inherent selectivity of the MoS2 atomic layer deposition (ALD) process is demonstrated by growth on common dielectric materials in contrast to thermal oxide/ nitride substrates. The selective deposition produced few layer MoS2 films on patterned growth regions as measured by Raman spectroscopy and time-of-flight secondary ion mass spectrometry. We additionally demonstrate that the selectivity can be enhanced by implementing atomic layer etching (ALE) steps at regular intervals during MoS2 growth. This area-selective ALD process provides an approach for integrating 2D films into next-generation devices by leveraging the inherent differences in surface chemistries and providing insight into the effectiveness of a supercycle ALD and ALE process.
- 30 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Open AccessIntrinsic and atomic layer etching enhanced area-selective atomic layer deposition of molybdenum disulfide thin films
For continual scaling in microelectronics, new processes for precise high volume fabrication are required. Area-selective atomic layer deposition (ASALD) can provide an avenue for self-aligned material patterning and offers an approach to correct edge placement errors commonly found in top-down patterning processes. Two-dimensional transition metal dichalcogenides also offer great potential in scaled microelectronic devices due to their high mobilities and few-atom thickness. In this work, we report ASALD of MoS2 thin films by deposition with MoF6 and H2S precursor reactants. The inherent selectivity of the MoS2 atomic layer deposition (ALD) process is demonstrated by growth on common dielectric materials in contrast to thermal oxide/ nitride substrates. The selective deposition produced few layer MoS2 films on patterned growth regions as measured by Raman spectroscopy and time-of-flight secondary ion mass spectrometry. We additionally demonstrate that the selectivity can be enhanced by implementing atomic layer etching (ALE) steps at regular intervals during MoS2 growth. This area-selective ALD process provides an approach for integrating 2D films into next-generation devices by leveraging the inherent differences in surface chemistries and providing insight into the effectiveness of a supercycle ALD and ALE process.
- 21 November 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (6)
Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides
To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS2), here we report studies of the reactions of molybdenum hexafluoride (MoF6) and hydrogen sulfide (H2S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ∼13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. These results provide an improved understanding of MoS2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS2 toward integration into device manufacturing.
- 21 November 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (6)
Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides
To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS2), here we report studies of the reactions of molybdenum hexafluoride (MoF6) and hydrogen sulfide (H2S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ∼13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. These results provide an improved understanding of MoS2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS2 toward integration into device manufacturing.
- 1 January 1991
- Published by Springer Nature in MRS Proceedings
- Vol. 229
Contamination Effects in Mo/Ni Superlattices
- 1 January 1991
- Published by Springer Nature in MRS Proceedings
- Vol. 229
Contamination Effects in Mo/Ni Superlattices
- 1 June 1990
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 6 (2-3) , 205-210
The application of energetic ion beams to thin metallic films
- 1 June 1990
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 6 (2-3) , 205-210
The application of energetic ion beams to thin metallic films