Jesse Wensel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jesse Wensel has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Elton Graugnard
Boise State University
2 shared publications - Steven M. Hues
Micron School of Materials Science and Engineering, Boise State University 1 , 1910 University Drive, Boise, Idaho 83725
2 shared publications - Arjan Singh
School of Electrical and Computer Engineering, Cornell University 3 , Ithaca, New York 14850
1 shared publication - Cameron A. Gorsak
Department of Materials Science and Engineering, Cornell University 2 , Ithaca, New York 14853
1 shared publication - Corey M. Efaw
Idaho National Laboratory
1 shared publication - Darrell G. Schlom
Department of Materials Science and Engineering, Cornell University 2 , Ithaca, New York 14853
1 shared publication
Latest Publications
- Open Access
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Achieving 0.05 Ω-mm contact resistance in non-alloyed Ti/Au ohmics to β-Ga2O3 by removing surface carbon
Preserving a contamination-free metal–semiconductor interface in β-Ga2O3 is critical to achieve consistently low resistance (< 1 Ω-mm) ohmic contacts. Here, we report a scanning transmission electron microscopy study on the variation in Ti/Au ohmic contact quality to (010) β-Ga2O3 in a conventional lift-off vs a metal-first process. We observe a thin ∼1 nm carbon barrier between the Ti and Ga2O3 in a non-conductive contact fabricated by a conventional lift-off process, which we attribute to photoresist residue, not previously detected by x-ray photoelectron spectroscopy due to the thinness and patchy coverage of the carbon layer, as well as roughness of the Ga2O3 surface. This thin carbon barrier is confirmed by electron energy loss spectroscopy and atomic force microscopy-infrared spectroscopy. We believe that the presence of the thin and patchy carbon layer leads to the highly inconsistent contact behavior in previous reports on non-alloyed contacts. Adventitious carbon is also observed in a conductive ohmic contact metal-first processing on an as-grown sample. We find that a five minute active oxygen descum is sufficient to remove this carbon on as-grown samples, further improving the ohmic behavior and reducing the contact resistance Rc to 0.06 Ω-mm. We also show that an hour long UV-ozone treatment of the Ga2O3 surface can eliminate carbon residue from the lift-off processing, resulting in a low Rc of 0.05 Ω-mm.
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Open AccessAchieving 0.05 Ω-mm contact resistance in non-alloyed Ti/Au ohmics to β-Ga2O3 by removing surface carbon
Preserving a contamination-free metal–semiconductor interface in β-Ga2O3 is critical to achieve consistently low resistance (< 1 Ω-mm) ohmic contacts. Here, we report a scanning transmission electron microscopy study on the variation in Ti/Au ohmic contact quality to (010) β-Ga2O3 in a conventional lift-off vs a metal-first process. We observe a thin ∼1 nm carbon barrier between the Ti and Ga2O3 in a non-conductive contact fabricated by a conventional lift-off process, which we attribute to photoresist residue, not previously detected by x-ray photoelectron spectroscopy due to the thinness and patchy coverage of the carbon layer, as well as roughness of the Ga2O3 surface. This thin carbon barrier is confirmed by electron energy loss spectroscopy and atomic force microscopy-infrared spectroscopy. We believe that the presence of the thin and patchy carbon layer leads to the highly inconsistent contact behavior in previous reports on non-alloyed contacts. Adventitious carbon is also observed in a conductive ohmic contact metal-first processing on an as-grown sample. We find that a five minute active oxygen descum is sufficient to remove this carbon on as-grown samples, further improving the ohmic behavior and reducing the contact resistance Rc to 0.06 Ω-mm. We also show that an hour long UV-ozone treatment of the Ga2O3 surface can eliminate carbon residue from the lift-off processing, resulting in a low Rc of 0.05 Ω-mm.
- Open Access
- 30 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Intrinsic and atomic layer etching enhanced area-selective atomic layer deposition of molybdenum disulfide thin films
For continual scaling in microelectronics, new processes for precise high volume fabrication are required. Area-selective atomic layer deposition (ASALD) can provide an avenue for self-aligned material patterning and offers an approach to correct edge placement errors commonly found in top-down patterning processes. Two-dimensional transition metal dichalcogenides also offer great potential in scaled microelectronic devices due to their high mobilities and few-atom thickness. In this work, we report ASALD of MoS2 thin films by deposition with MoF6 and H2S precursor reactants. The inherent selectivity of the MoS2 atomic layer deposition (ALD) process is demonstrated by growth on common dielectric materials in contrast to thermal oxide/ nitride substrates. The selective deposition produced few layer MoS2 films on patterned growth regions as measured by Raman spectroscopy and time-of-flight secondary ion mass spectrometry. We additionally demonstrate that the selectivity can be enhanced by implementing atomic layer etching (ALE) steps at regular intervals during MoS2 growth. This area-selective ALD process provides an approach for integrating 2D films into next-generation devices by leveraging the inherent differences in surface chemistries and providing insight into the effectiveness of a supercycle ALD and ALE process.
- 30 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Open AccessIntrinsic and atomic layer etching enhanced area-selective atomic layer deposition of molybdenum disulfide thin films
For continual scaling in microelectronics, new processes for precise high volume fabrication are required. Area-selective atomic layer deposition (ASALD) can provide an avenue for self-aligned material patterning and offers an approach to correct edge placement errors commonly found in top-down patterning processes. Two-dimensional transition metal dichalcogenides also offer great potential in scaled microelectronic devices due to their high mobilities and few-atom thickness. In this work, we report ASALD of MoS2 thin films by deposition with MoF6 and H2S precursor reactants. The inherent selectivity of the MoS2 atomic layer deposition (ALD) process is demonstrated by growth on common dielectric materials in contrast to thermal oxide/ nitride substrates. The selective deposition produced few layer MoS2 films on patterned growth regions as measured by Raman spectroscopy and time-of-flight secondary ion mass spectrometry. We additionally demonstrate that the selectivity can be enhanced by implementing atomic layer etching (ALE) steps at regular intervals during MoS2 growth. This area-selective ALD process provides an approach for integrating 2D films into next-generation devices by leveraging the inherent differences in surface chemistries and providing insight into the effectiveness of a supercycle ALD and ALE process.