Zulkifli Ahmad
Research Subjects
Research Interests
Zulkifli Ahmad has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Aziz Adam
Fakulti Teknologi Kejuruteraan Mekanikal dan Pembuatan, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, Durian Tunggal 76100, Melaka, Malaysia
1 shared publication - Hadzley Abu Bakar
Universiti Teknikal Malaysia Melaka (UTeM), Malaysia
1 shared publication - Lailatul Harina Paijan
Faculty of Industrial and Manufacturing Technology and Engineering Universiti Teknikal Malaysia Melaka Hang Tuah Jaya Durian Tunggal 76100 Melaka Malaysia
1 shared publication - Mohd Basri Ali
Faculty of Industrial and Manufacturing Engineering Technology, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian, Malaysia
1 shared publication - Mohd Fauzi Mamat
Faculty of Industrial and Manufacturing Technology and Engineering (FTKIP) Kampus Teknologi Universiti Teknikal Malaysia Melaka (UTeM) Hang Tuah Jaya Durian Tunggal 76100 Melaka Malaysia
1 shared publication - Norfariza Ab Wahab
Department of Mechanical Engineering Technology Faculty of Mechanical and Manufacturing Engineering Technology Universiti Teknikal Malaysia Melaka Hang Tuah Jaya Durian Tunggal 76100 Melaka Malaysia
1 shared publication
Latest Publications
- Open Access
- 22 November 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (12) , 325
Effect of Sintering Parameters on the Mechanical Properties and Wear Performance of Alumina Inserts
The sintering temperature and holding time have a significant impact on the densification of a ceramic compact. In this study, alumina inserts were made with varying sintering temperatures and holding times. The procedure began with the compacting of alumina powders inside a mould with trapezium and round shapes. These inserts were then sintered between 1200 °C and 1400 °C for 5 to 9 h holding time. The sintered samples underwent analysis based on the shrinkage size, density, and microstructure. The sample with the highest density was chosen for additional machining tests. The results showed that the alumina shrinkage ranged from 3 to 6%, with a maximum relative density of 91.3% recorded when the sintering parameter was applied at 1400 °C and a 9 h holding time. The transition of the grain growth was observed depending on the sintering temperature and heating duration. When machined with AISI 1045 carbon steel, the sintered alumina inserts achieved a maximum tool life of 35 s at a cutting speed of 350 m/min. The sintered inserts exhibited brittle characteristics with a dominant notch wear and abrasive mechanisms.
- 22 November 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (12) , 325
Open AccessEffect of Sintering Parameters on the Mechanical Properties and Wear Performance of Alumina Inserts
The sintering temperature and holding time have a significant impact on the densification of a ceramic compact. In this study, alumina inserts were made with varying sintering temperatures and holding times. The procedure began with the compacting of alumina powders inside a mould with trapezium and round shapes. These inserts were then sintered between 1200 °C and 1400 °C for 5 to 9 h holding time. The sintered samples underwent analysis based on the shrinkage size, density, and microstructure. The sample with the highest density was chosen for additional machining tests. The results showed that the alumina shrinkage ranged from 3 to 6%, with a maximum relative density of 91.3% recorded when the sintering parameter was applied at 1400 °C and a 9 h holding time. The transition of the grain growth was observed depending on the sintering temperature and heating duration. When machined with AISI 1045 carbon steel, the sintered alumina inserts achieved a maximum tool life of 35 s at a cutting speed of 350 m/min. The sintered inserts exhibited brittle characteristics with a dominant notch wear and abrasive mechanisms.