Effect of Sintering Parameters on the Mechanical Properties and Wear Performance of Alumina Inserts
Authors:
- Abdul Aziz AdamAAAbdul Aziz Adam
- Hadzley Abu BakarHBHadzley Abu Bakar
- Umar Al AmaniUAUmar Al Amani
- Lailatul Harina PaijanLPLailatul Harina Paijan
- Norfariza Ab WahabNWNorfariza Ab Wahab
- Mohd Fauzi MamatMMMohd Fauzi Mamat
- Mohd Basri AliMAMohd Basri Ali
- Safarudin Gazali HerawanSHSafarudin Gazali Herawan
- Zulkifli AhmadZAZulkifli Ahmad
Open Access
- 22 November 2022
- journal article
- research article
- Published by MDPI AG in Lubricants
- Vol. 10 (12) , 325
Abstract
The sintering temperature and holding time have a significant impact on the densification of a ceramic compact. In this study, alumina inserts were made with varying sintering temperatures and holding times. The procedure began with the compacting of alumina powders inside a mould with trapezium and round shapes. These inserts were then sintered between 1200 °C and 1400 °C for 5 to 9 h holding time. The sintered samples underwent analysis based on the shrinkage size, density, and microstructure. The sample with the highest density was chosen for additional machining tests. The results showed that the alumina shrinkage ranged from 3 to 6%, with a maximum relative density of 91.3% recorded when the sintering parameter was applied at 1400 °C and a 9 h holding time. The transition of the grain growth was observed depending on the sintering temperature and heating duration. When machined with AISI 1045 carbon steel, the sintered alumina inserts achieved a maximum tool life of 35 s at a cutting speed of 350 m/min. The sintered inserts exhibited brittle characteristics with a dominant notch wear and abrasive mechanisms.Keywords
Funding Information
- Jabatan Pendidikan Tinggi Kementerian Pengajian Tinggi (FRGS/1/2020/FTKMP-CARE/F00438)
This publication has 25 references indexed in Scilit:
- Microwave sintering of zirconia-toughened alumina (ZTA)-TiO2-Cr2O3 ceramic composite: The effects on microstructure and propertiesJournal of Alloys and Compounds, 2017
- Fabrication and cutting performance of an Al2O3/TiC/TiN ceramic cutting tool in turning of an ultra-high-strength steelThe International Journal of Advanced Manufacturing Technology, 2016
- Effects of Cr 2 O 3 addition on the phase, mechanical properties, and microstructure of zirconia-toughened alumina added with TiO 2 (ZTA–TiO 2 ) ceramic compositeInternational Journal of Refractory Metals and Hard Materials, 2016
- Machinability evaluation and desirability function optimization of turning parameters for Cr 2 O 3 doped zirconia toughened alumina (Cr-ZTA) cutting insert in high speed machining of steelCeramics International, 2016
- Shrinkage characteristics studies on conventional sintered zirconia toughened alumina using computed tomography imaging techniqueInternational Journal of Refractory Metals and Hard Materials, 2016
- An Integral Method to Determine Workpiece Flow Stress and Friction Characteristics in Metal CuttingInternational Journal of Automation Technology, 2015
- Cutting performance and life prediction of an Al2O3/TiC micro–nano-composite ceramic tool when machining austenitic stainless steelCeramics International, 2015
- Development of Ce‐ PSZ ‐/Y‐ PSZ ‐Toughened Alumina Inserts for High‐Speed Machining SteelInternational Journal of Applied Ceramic Technology, 2013
- The influence of additives on microstrucutre of sub-micron alumina ceramics prepared by two-stage sinteringJournal of the European Ceramic Society, 2012
- Effects of Cr2O3 addition on the mechanical properties, microstructure and wear performance of zirconia-toughened-alumina (ZTA) cutting insertsJournal of Alloys and Compounds, 2012