Al-Saudi Sarah Kareem Mohammed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Al-Saudi Sarah Kareem Mohammed has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Róbert Géber
Faculty of Materials and Chemical Engineering, Institute of Energy, Ceramic and Polymer Technology, University of Miskolc, Miskolc-Egyetemvaros, Hungary
2 shared publications - Andrea Simon
Institute of Ceramics and Polymer Engineering, University of Miskolc, H-3515, Miskolc-Egyetemváros, Hungary
1 shared publication
Latest Publications
- Open Access
- 26 March 2025
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 20 (1) , 110-116
Effect of liquid-solid ratio on metakaolin-based geopolymer binder properties
This article aims to achieve the hardening of geopolymer binder-based metakaolin under the same setting time and hardening temperature as traditional cement. It studied the hardening of the geopolymer binder-based metakaolin at two temperatures of 60 °C and room temperature using different liquid-to-solid ratios of 0.8, 0.95, and 1.1. The bulk density, compressive strength, sitting times, thermal conductivity, and microstructure were measured for geopolymer binders. Based on the specified range for cement characteristics, the geopolymer binder was solidified at room temperature, utilizing a liquid-to-solid ratio of 0.8 to achieve optimal results stratified according to the cement's ideal characteristics. It had a bulk density of 1.264 g cm−3, compressive strength of 19.12 MPa, initial setting time of 288 min, final setting time of 358 min, and thermal conductivity of 0.49 W m−1 K.
- 26 March 2025
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 20 (1) , 110-116
Open AccessEffect of liquid-solid ratio on metakaolin-based geopolymer binder properties
This article aims to achieve the hardening of geopolymer binder-based metakaolin under the same setting time and hardening temperature as traditional cement. It studied the hardening of the geopolymer binder-based metakaolin at two temperatures of 60 °C and room temperature using different liquid-to-solid ratios of 0.8, 0.95, and 1.1. The bulk density, compressive strength, sitting times, thermal conductivity, and microstructure were measured for geopolymer binders. Based on the specified range for cement characteristics, the geopolymer binder was solidified at room temperature, utilizing a liquid-to-solid ratio of 0.8 to achieve optimal results stratified according to the cement's ideal characteristics. It had a bulk density of 1.264 g cm−3, compressive strength of 19.12 MPa, initial setting time of 288 min, final setting time of 358 min, and thermal conductivity of 0.49 W m−1 K.
- Open Access
- 1 January 2022
- Published by Multidiszciplinaris tudomanyok in Multidiszciplináris tudományok
- Vol. 12 (4) , 189-197
Preparation and characterization of foam glass from soda lime silicate glass waste by using different dosages of limestone
Soda-lime silicate (SLS) waste glass is a kind of solid waste that is produced in large quantities as container glass or flat glass. In this work, waste window glass is used to produce foam glass using limestone as a foaming agent. The pore structure of the foam glass and the optimization of its properties by adjusting the amount of glass and foaming agents were investigated in this work. The formation of foam glass was studied on samples prepared from blends of SLS waste glass with 0.5 wt% SiC and 2, 4, 6 wt% limestone by sintering at 800 °C. The foam glass with 2wt % limestone presented a homogeneous foam structure with low body density (0.26 g/cm3), apparent porosity (9 vol%) and thermal conductivity (0.04 W/m∙K). When the limestone content increases to 6 wt %, the density and thermal conductivity of the sample also increases to 0.92 g/cm3 and 0.13 W/m∙K, respectively.
- 1 January 2022
- Published by Multidiszciplinaris tudomanyok in Multidiszciplináris tudományok
- Vol. 12 (4) , 189-197
Open AccessPreparation and characterization of foam glass from soda lime silicate glass waste by using different dosages of limestone
Soda-lime silicate (SLS) waste glass is a kind of solid waste that is produced in large quantities as container glass or flat glass. In this work, waste window glass is used to produce foam glass using limestone as a foaming agent. The pore structure of the foam glass and the optimization of its properties by adjusting the amount of glass and foaming agents were investigated in this work. The formation of foam glass was studied on samples prepared from blends of SLS waste glass with 0.5 wt% SiC and 2, 4, 6 wt% limestone by sintering at 800 °C. The foam glass with 2wt % limestone presented a homogeneous foam structure with low body density (0.26 g/cm3), apparent porosity (9 vol%) and thermal conductivity (0.04 W/m∙K). When the limestone content increases to 6 wt %, the density and thermal conductivity of the sample also increases to 0.92 g/cm3 and 0.13 W/m∙K, respectively.