Zakaria Djebbour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zakaria Djebbour has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Abdelillah Slaoui
ICube
1 shared publication - Alain Fave
Institut des Nanotechnologies de Lyon (INL), UMR 5270, École Centrale de Lyon, Institut National des Sciences Appliquées (INSA) Lyon, Université Claude Bernard Lyon 1
1 shared publication - Albert Minj
Imec, Kapeldreef 75, 3001 Leuven, Belgium
1 shared publication - Pierre Bellanger
Semilab,Budapest,Hungary
1 shared publication - Stéphane Roques
ICube Laboratory, University of Strasbourg, CNRS (Centre National de la Recherche Scientifique)
1 shared publication
Latest Publications
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (6) , 1436-1442
Silicon Tunnel Junctions Produced by Ion Implantation and Diffusion Processes for Tandem Solar Cells
This work reports on the fabrication of silicon tunnel junctions that can be used in silicon-based bottom cells for tandem solar cells. The tunnel junction was formed on n-type monocrystalline silicon wafers using the following two different processes: 1) a thermal diffusion of boron followed by an arsenic ion implantation; and 2) successive implantation steps of boron and arsenic ions. For both the processes, a rapid thermal annealing step was used to activate the dopants and cure the defects generated by the ion implantation. The activated dopant distribution across the tunnel junction was determined by electrochemical capacitance–voltage (ECV) measurements. The quality of the device was assessed from the peak-to-valley ratio and peak current density of its current–voltage characteristics, as well as the resistivity. As a significant result, a peak current density value and a peak-to-valley ratio of approximately 50 A/cm2 and 1.7, respectively, were obtained for two consecutive implantations of boron and arsenic, followed by thermal annealing at 925 °C for 30 min. A very narrow depletion zone of 3.9 nm was calculated from the ECV dopant concentrations measurements under full depletion approximation. Finally, solar cells fabricated using this optimized process resulted in a conversion efficiency of 10.1% against 12% obtained from the reference monocrystalline solar cell.
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (6) , 1436-1442
Silicon Tunnel Junctions Produced by Ion Implantation and Diffusion Processes for Tandem Solar Cells
This work reports on the fabrication of silicon tunnel junctions that can be used in silicon-based bottom cells for tandem solar cells. The tunnel junction was formed on n-type monocrystalline silicon wafers using the following two different processes: 1) a thermal diffusion of boron followed by an arsenic ion implantation; and 2) successive implantation steps of boron and arsenic ions. For both the processes, a rapid thermal annealing step was used to activate the dopants and cure the defects generated by the ion implantation. The activated dopant distribution across the tunnel junction was determined by electrochemical capacitance–voltage (ECV) measurements. The quality of the device was assessed from the peak-to-valley ratio and peak current density of its current–voltage characteristics, as well as the resistivity. As a significant result, a peak current density value and a peak-to-valley ratio of approximately 50 A/cm2 and 1.7, respectively, were obtained for two consecutive implantations of boron and arsenic, followed by thermal annealing at 925 °C for 30 min. A very narrow depletion zone of 3.9 nm was calculated from the ECV dopant concentrations measurements under full depletion approximation. Finally, solar cells fabricated using this optimized process resulted in a conversion efficiency of 10.1% against 12% obtained from the reference monocrystalline solar cell.