Charles R. Ebbing
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Charles R. Ebbing has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bibek Gautam
Department of Physics and Astronomy, University of Kansas, Lawrence, KS, USA
2 shared publications - Haiyan Wang
School of Materials Engineering, Purdue University, West Lafayette, USA
2 shared publications - Judy Z. Wu
Department of Physics and Astronomy, University of Kansas, Lawrence, KS 66045, USA
2 shared publications - Mary Ann Sebastian
University of Dayton Research Institute, Dayton, OH, USA
2 shared publications - Timothy J. Haugan
Air Force Research Laboratory, Aerospace Systems Directorate, Wright-Patterson AFB, OH, USA
2 shared publications - George Y. Panasyuk
Aerospace Systems Directorate, Air Force Research Laboratory, Wright-Patterson Air Force Base, Ohio 45433, USA
1 shared publication
Latest Publications
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Ramifications of Pulsed Laser Deposition Growth Temperature on BaHfO3 and Y2O3 Doped Y-Ba-Cu-O Thin Films’ Microstructure and Performance
Deposition temperature is an important parameter to control in pulsed laser deposition of thin films, as it affects the ad-atom mobility and diffusion in regards to film growth. Increased growth temperature can also result in increased stacking fault densities in YBa 2 Cu 3 O 7-δ (YBCO) films. This research investigates the influence of deposition temperature on the critical current density and the microstructure of YBCO thin films double doped with BaHfO 3 and Y 2 O 3 . A KrF excimer laser was used to produce thin films of YBCO doped with 4 vol. % BaHfO 3 and 3 vol. % Y 2 O 3 on LaAlO 3 (LAO) substrates at various deposition temperatures from 790–825 °C. The growth temperature influence on the flux pinning landscape and Jc (H,T,θ) properties ( T = 5–77 K, H = 0–9 T, θ = 0–180°) of these films will be presented.
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (5) , 1-5
Ramifications of Pulsed Laser Deposition Growth Temperature on BaHfO3 and Y2O3 Doped Y-Ba-Cu-O Thin Films’ Microstructure and Performance
Deposition temperature is an important parameter to control in pulsed laser deposition of thin films, as it affects the ad-atom mobility and diffusion in regards to film growth. Increased growth temperature can also result in increased stacking fault densities in YBa 2 Cu 3 O 7-δ (YBCO) films. This research investigates the influence of deposition temperature on the critical current density and the microstructure of YBCO thin films double doped with BaHfO 3 and Y 2 O 3 . A KrF excimer laser was used to produce thin films of YBCO doped with 4 vol. % BaHfO 3 and 3 vol. % Y 2 O 3 on LaAlO 3 (LAO) substrates at various deposition temperatures from 790–825 °C. The growth temperature influence on the flux pinning landscape and Jc (H,T,θ) properties ( T = 5–77 K, H = 0–9 T, θ = 0–180°) of these films will be presented.
- 10 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Comparison Study of the Flux Pinning Enhancement of YBa2Cu3O7−δ Thin Films With BaHfO3 + Y2O3 Single- and Mixed-Phase Additions
Incorporating nano-scale insulating phases to YBa $_{2}$ Cu $_{3}$ O $_{7-\delta}$ (YBCO) superconductor thin films enhances flux pinning by combining different pinning mechanisms, which in turn increases current density. This research explores the effects of addition of the non-reactive phases of barium hafnate (BHO) and yttrium oxide Y $_{2}$ O $_{3}$ . Pulsed laser deposition (PLD) produces thin films on SrTiO $_{3}$ (STO) substrates at various deposition temperatures ranging from 790 °C to 840 °C. PLD target compositions vary the volume percent of BHO from 2-6 vol. %, while maintaining 3 vol. % Y $_{2}$ O $_{3}$ , and the remaining vol. % YBCO. Examining the microstructure through SEM, TEM, and XRD analysis provides insight into the impact of the additions of BHO and Y $_{2}$ O $_{3}$ on the YBCO thin films' magnetic and transport current densities measured with an applied field parallel to the c and ab directions, and on the films' critical temperature measurements. The Y $_{2}$ O $_{3}$ additions decrease the variability in the current density between the c and ab directions, which is an important aspect to consider in applications, such as for HTS wires for motors.- 10 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Comparison Study of the Flux Pinning Enhancement of YBa2Cu3O7−δ Thin Films With BaHfO3 + Y2O3 Single- and Mixed-Phase Additions
Incorporating nano-scale insulating phases to YBa $_{2}$ Cu $_{3}$ O $_{7-\delta}$ (YBCO) superconductor thin films enhances flux pinning by combining different pinning mechanisms, which in turn increases current density. This research explores the effects of addition of the non-reactive phases of barium hafnate (BHO) and yttrium oxide Y $_{2}$ O $_{3}$ . Pulsed laser deposition (PLD) produces thin films on SrTiO $_{3}$ (STO) substrates at various deposition temperatures ranging from 790 °C to 840 °C. PLD target compositions vary the volume percent of BHO from 2-6 vol. %, while maintaining 3 vol. % Y $_{2}$ O $_{3}$ , and the remaining vol. % YBCO. Examining the microstructure through SEM, TEM, and XRD analysis provides insight into the impact of the additions of BHO and Y $_{2}$ O $_{3}$ on the YBCO thin films' magnetic and transport current densities measured with an applied field parallel to the c and ab directions, and on the films' critical temperature measurements. The Y $_{2}$ O $_{3}$ additions decrease the variability in the current density between the c and ab directions, which is an important aspect to consider in applications, such as for HTS wires for motors.