Ali Sabri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ali Sabri has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ayad Ali Mohammed
Al-Mussaib Technical College, Al-Furat Al-Awsat Technical University, Babylon 51006, Iraq
2 shared publications Noor Y. Abbas
2 shared publicationsRand Nabil
2 shared publications- Noor Yehia
Department of Mechanical Engineering, Al-Nahrain University, Baghdad, Iraq
1 shared publication - Rand Nabil
Collage of Engineering, Al-Nahrain University, Department of Mechanical Engineering, Jadriya, Baghdad, Iraq
1 shared publication - Thiago Santos
Technology Center, Federal University of Rio Grande do Norte, Av. Prof. Sen. Salgado Filho, 3000, Natal, Rio Grande do Norte, 59072-970, Brazil
1 shared publication
Latest Publications
- Open Access
- 31 December 2025
- Published by International Information and Engineering Technology Association in International Journal of Heat and Technology
- Vol. 43 (6) , 2339-2349
Enhanced Heat Transfer in Plate-Fin Heat Exchangers Using Offset Triangular Fins with Vortex Generators: A Numerical Study
- 31 December 2025
- Published by International Information and Engineering Technology Association in International Journal of Heat and Technology
- Vol. 43 (6) , 2339-2349
Open AccessEnhanced Heat Transfer in Plate-Fin Heat Exchangers Using Offset Triangular Fins with Vortex Generators: A Numerical Study
- Open Access
- 15 June 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 132 (1) , 22-46
Investigation of Improving Heat Transfer Efficiency using Perforated Fins: A Review
Because of their potential to increase accessible area and overall heat diffusion, fins are often used as a thermal control approach for heat exchange. Nevertheless, these surfaces have undergone several modifications to improve their performance, one of which is perforation. Perforation shows outstanding promise in augmenting exchanged heat by enhancing turbulent stream and, most importantly, reducing the mass of these fins. The core goal of this review is to provide an extensive summarisation of the perforation impact as passive approaches that aim to enhance the thermo-hydraulic features of various fin forms that are employed in different applications, like heat sinks in electronics cooling, and heat exchangers in air-conditioning. Perforation in various fin shapes has been covered, such as (round, plate, longitudinal, pin, etc,) along with different parameters to investigate hole diameter, hole shape, hole quantity, hole distance, etc. Selected research was conducted under different conditions (forced and free convection, laminar and turbulent flow, and steady and unsteady). According to previous studies, drilled fins have a higher rate of heat than regular ones. The review concluded that freshly designed drilled fins outperform solid fins in enhancing the rate of heat transfer in a variety of thermal systems.
- 15 June 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 132 (1) , 22-46
Open AccessInvestigation of Improving Heat Transfer Efficiency using Perforated Fins: A Review
Because of their potential to increase accessible area and overall heat diffusion, fins are often used as a thermal control approach for heat exchange. Nevertheless, these surfaces have undergone several modifications to improve their performance, one of which is perforation. Perforation shows outstanding promise in augmenting exchanged heat by enhancing turbulent stream and, most importantly, reducing the mass of these fins. The core goal of this review is to provide an extensive summarisation of the perforation impact as passive approaches that aim to enhance the thermo-hydraulic features of various fin forms that are employed in different applications, like heat sinks in electronics cooling, and heat exchangers in air-conditioning. Perforation in various fin shapes has been covered, such as (round, plate, longitudinal, pin, etc,) along with different parameters to investigate hole diameter, hole shape, hole quantity, hole distance, etc. Selected research was conducted under different conditions (forced and free convection, laminar and turbulent flow, and steady and unsteady). According to previous studies, drilled fins have a higher rate of heat than regular ones. The review concluded that freshly designed drilled fins outperform solid fins in enhancing the rate of heat transfer in a variety of thermal systems.
- Open Access
- 10 February 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 127 (1) , 161-174
Finned Tube Heat Exchanger Enhancements with Needle Fin Shapes
Finned-tube heat exchangers with low weight and good thermal characteristics are required to meet new heat transfer issues and rising application demand. Fins increase the flow mixture, lower the recirculating zone, and distribute heat to the environment to preserve system thermal efficiency. This research explores thermo-hydraulic characteristics, weight reduction, and performance parameter for 17 examples with 0.5 mm needle fin thickness with 10 mm altitude and diverse forms, including six angles (80°, 70°, 60°, 50°, 40°, and 30°) and three vertices (6, 8, and 10 Each is compared to equal-sized circular fins. SOLID WORK 2021 generated 3D geometry and heat exchanger weight reduction values. At 4,300 Reynold number, ANSYS FLUENT 2020 R2 estimated heat transfer effect of each air-water heat exchanger form. All needle fins outperformed solid fins in heat transfer. By decreasing the number of vertices (N) and their angles (Ɵ), thermal characteristics have improved. For instance, lowering (N) from 10 to 6 and (Ɵ) from 80° to 30° leads to increased Nusselt number (Nu) by 40.76 % -154.78 %, 26.27 % -76.29 %, 29.24% -202.37 %, and heat flow rate per unit area (Q/m^2) by 26%-76%, 25%-62%, and 14.33-49% Heat exchangers using proposed needle designs saved 37% in weight (w) and 37%-15%, 12%-15%, and 9%- 10% in friction factor (f) for 80°-30°.
- 10 February 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 127 (1) , 161-174
Open AccessFinned Tube Heat Exchanger Enhancements with Needle Fin Shapes
Finned-tube heat exchangers with low weight and good thermal characteristics are required to meet new heat transfer issues and rising application demand. Fins increase the flow mixture, lower the recirculating zone, and distribute heat to the environment to preserve system thermal efficiency. This research explores thermo-hydraulic characteristics, weight reduction, and performance parameter for 17 examples with 0.5 mm needle fin thickness with 10 mm altitude and diverse forms, including six angles (80°, 70°, 60°, 50°, 40°, and 30°) and three vertices (6, 8, and 10 Each is compared to equal-sized circular fins. SOLID WORK 2021 generated 3D geometry and heat exchanger weight reduction values. At 4,300 Reynold number, ANSYS FLUENT 2020 R2 estimated heat transfer effect of each air-water heat exchanger form. All needle fins outperformed solid fins in heat transfer. By decreasing the number of vertices (N) and their angles (Ɵ), thermal characteristics have improved. For instance, lowering (N) from 10 to 6 and (Ɵ) from 80° to 30° leads to increased Nusselt number (Nu) by 40.76 % -154.78 %, 26.27 % -76.29 %, 29.24% -202.37 %, and heat flow rate per unit area (Q/m^2) by 26%-76%, 25%-62%, and 14.33-49% Heat exchangers using proposed needle designs saved 37% in weight (w) and 37%-15%, 12%-15%, and 9%- 10% in friction factor (f) for 80°-30°.
- Open Access
- 29 May 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (7) , 131-147
Improvement of Plate-Fin Heat Exchanger Performance with Assistance of Various Types of Vortex Generator
A 3-dimensional incompressible laminar flow and heat-transfer in a plate-fin heat exchanger (PFHE) where investigated numerically in this article. The influence of mounting a longitudinal vortex generator (LVG) on the offset rectangular-triangular fin (ORT) in the PFHE, on thermal and hydro-dynamic fields are presented. The novelty of this study is by attaching a LVG to an offset strip fin (OSF) surface. The cases of study for the PFHE are established, by using a built-in rectangular winglet pair type RWP longitudinal vortex generator carried out and fitted on this fin to improve the convective heat transfer of the (ORT) fin while minimizing pressure loss. The upper and lower plates are exposed to constant heat flux and the working fluid is air where chosen under a laminar range of RE (600 to 1400). The laminar flow and heat-transfer are governed by continuity, momentum and energy equations. ANSYS FLUENT (2021 R1) is used to get the numerical results, based on the finite volume method. The performance of the VG is assessed for an optimum winglet attack angle (45°), as well as by modifying the geometrical size parameters, namely the height and placement (L) of the RWP LVG. The result shows that the Nusselt number reaches its optimum enhancement values by using a common flow up CFU built-in rectangular winglet pair type RWP VG with a height and entrance length of (h=1.25mm, L=0.5mm), by 22.23% as compared with base case configuration (ORT). Finally, a two more LVG are tested with the optimum conditions of the RWP, which they are a delta winglet pair (DWP) and trapezoidal winglet pair (TWP). In addition, the temperature fields for the primary and secondary flows were shown in contour and streamline diagrams
- 29 May 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (7) , 131-147
Open AccessImprovement of Plate-Fin Heat Exchanger Performance with Assistance of Various Types of Vortex Generator
A 3-dimensional incompressible laminar flow and heat-transfer in a plate-fin heat exchanger (PFHE) where investigated numerically in this article. The influence of mounting a longitudinal vortex generator (LVG) on the offset rectangular-triangular fin (ORT) in the PFHE, on thermal and hydro-dynamic fields are presented. The novelty of this study is by attaching a LVG to an offset strip fin (OSF) surface. The cases of study for the PFHE are established, by using a built-in rectangular winglet pair type RWP longitudinal vortex generator carried out and fitted on this fin to improve the convective heat transfer of the (ORT) fin while minimizing pressure loss. The upper and lower plates are exposed to constant heat flux and the working fluid is air where chosen under a laminar range of RE (600 to 1400). The laminar flow and heat-transfer are governed by continuity, momentum and energy equations. ANSYS FLUENT (2021 R1) is used to get the numerical results, based on the finite volume method. The performance of the VG is assessed for an optimum winglet attack angle (45°), as well as by modifying the geometrical size parameters, namely the height and placement (L) of the RWP LVG. The result shows that the Nusselt number reaches its optimum enhancement values by using a common flow up CFU built-in rectangular winglet pair type RWP VG with a height and entrance length of (h=1.25mm, L=0.5mm), by 22.23% as compared with base case configuration (ORT). Finally, a two more LVG are tested with the optimum conditions of the RWP, which they are a delta winglet pair (DWP) and trapezoidal winglet pair (TWP). In addition, the temperature fields for the primary and secondary flows were shown in contour and streamline diagrams
- Open Access
- 11 November 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 99 (2) , 48-66
Enhancement Of Plate-Fin Heat Exchanger Performance with Aid of Various Types of Fin Configurations: A Review
This study is a review of recent studies on heat transfer enhancement in plate fin-heat exchangers (PFHE) with plain and offset (OSF) fins. Thermal designing parameters such as the coefficient of heat transfer, Nusselt number, hydraulic diameter, Colburn factor (j), friction factor (f) and Reynold's number of PFHE was presented in this review for both straight and offset types. According to the results, by replacing plain fins into OSF, the pressure increases because of the increasing of f-factor, while there is a significant increase in Nusselt number and then the heat transfer. The j & f factors, are the most essential two parameters of researching the heat exchanger that were represented as functions of Reynolds number and other geometrical parameters. At the same Reynolds number, the J-factor declines and the friction factor f increases as the fin pitch increases for the same fin height and fin thickness.
- 11 November 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 99 (2) , 48-66
Open AccessEnhancement Of Plate-Fin Heat Exchanger Performance with Aid of Various Types of Fin Configurations: A Review
This study is a review of recent studies on heat transfer enhancement in plate fin-heat exchangers (PFHE) with plain and offset (OSF) fins. Thermal designing parameters such as the coefficient of heat transfer, Nusselt number, hydraulic diameter, Colburn factor (j), friction factor (f) and Reynold's number of PFHE was presented in this review for both straight and offset types. According to the results, by replacing plain fins into OSF, the pressure increases because of the increasing of f-factor, while there is a significant increase in Nusselt number and then the heat transfer. The j & f factors, are the most essential two parameters of researching the heat exchanger that were represented as functions of Reynolds number and other geometrical parameters. At the same Reynolds number, the J-factor declines and the friction factor f increases as the fin pitch increases for the same fin height and fin thickness.