Ayad Ali Mohammed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ayad Ali Mohammed has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Ali Sabri Abbas
3 shared publications- Ali Sabri
Department of Mechanical Engineering, Al-Nahrain University, Baghdad, Iraq
2 shared publications - Abdul Amir Hassan Kadhum
Department of Chemical & Process Engineering, Universiti Kebangsaan Malaysia (UKM), Bangi, Selangor 43000, Malaysia
1 shared publication - Ahmed Abdulameir Al-Amiery
Department of Science and Technology Parks, Al-Ayen University (AUIQ), Nasiriyah, Iraq
1 shared publication Akeel Abdullah Mohammed
1 shared publication- Ali Fadhil Naser
Harbin Institute of Technology
1 shared publication
Latest Publications
- Open Access
- 30 April 2026
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 36 (2) , 395-406
Multi-Objective Optimization and Surrogate Modeling of Composite Morphing Airfoils: Trends, Bottlenecks, and Research Priorities
- 30 April 2026
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 36 (2) , 395-406
Open AccessMulti-Objective Optimization and Surrogate Modeling of Composite Morphing Airfoils: Trends, Bottlenecks, and Research Priorities
- Open Access
- 31 December 2025
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 35 (06) , 1199-1209
Experimental Evaluation of Morphing Wing Technologies: A Systematic Review
- 31 December 2025
- Published by International Information and Engineering Technology Association in Revue des composites et des matériaux avancés
- Vol. 35 (06) , 1199-1209
Open AccessExperimental Evaluation of Morphing Wing Technologies: A Systematic Review
- 18 July 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 38 (1) , 116-142
Enhancing the Thermal Efficiency of Compact Heat Exchangers through Novel Twisted Fin Configurations
With the increasing requirement for energy saving in industrial processes, the enhanced heat transfer performance of the compact heat exchanger (CHE) is more urgently needed. Traditional conjugate straight fin geometries have limitations in producing strong secondary flows for mixing, leading to a subpar thermal-hydraulic performance. The current work attempts to fill this gap by analysing a new twisted fin as a passive heat transfer enhancement technique. The code aims to find the best twist ratio to keep good thermal performance while having acceptable pressure penalties on a laminar flow condition. By employing CFD (Computational Fluid Dynamics), with ANSYS Fluent 2021 R1, we studied the complete set of three different twisting ratios (0.77, 0.55, 0.33) over the Reynolds numbers 600–1400. The numerical strategy adopted the pressure-based solver with the SIMPLE algorithm and second-order upwind discretisation scheme, benchmarked with the experimental data and the average accuracy was 4.2% and 3 % for pressure drop and j-factor, respectively. The results showed that the TF55 combined with the use of a 55% loss cable configuration yielded the best thermal-fluid performance with heat transfer enhancements between 38-54% and pressure penalties between 42-56%, resulting in peak PEC of 1.81 at Re = 1400an 81% improvement over the conventional straight fin. The more aggressive TF33 knockoff produced higher heat transfer enhancement values (45-62%) with unacceptably high-pressure penalties (68-85%), while the intermediate TF77 knockoff provided only marginal increments (28-42%) with modest pressure penalties (25-35%). The results indicated that the formation of the secondary flow and disturbance to the thermal boundary layer are the main mechanisms responsible for heat transfer augmentation, and the 0.55 twist ratio represents the best tradeoff between the effect of thermal mixing enhancement and hydraulic pumping power consumption. This study is aimed at the development of compact heat exchanger designs, which are of relevance for high-efficiency and space-limited applications.
- 18 July 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 38 (1) , 116-142
Enhancing the Thermal Efficiency of Compact Heat Exchangers through Novel Twisted Fin Configurations
With the increasing requirement for energy saving in industrial processes, the enhanced heat transfer performance of the compact heat exchanger (CHE) is more urgently needed. Traditional conjugate straight fin geometries have limitations in producing strong secondary flows for mixing, leading to a subpar thermal-hydraulic performance. The current work attempts to fill this gap by analysing a new twisted fin as a passive heat transfer enhancement technique. The code aims to find the best twist ratio to keep good thermal performance while having acceptable pressure penalties on a laminar flow condition. By employing CFD (Computational Fluid Dynamics), with ANSYS Fluent 2021 R1, we studied the complete set of three different twisting ratios (0.77, 0.55, 0.33) over the Reynolds numbers 600–1400. The numerical strategy adopted the pressure-based solver with the SIMPLE algorithm and second-order upwind discretisation scheme, benchmarked with the experimental data and the average accuracy was 4.2% and 3 % for pressure drop and j-factor, respectively. The results showed that the TF55 combined with the use of a 55% loss cable configuration yielded the best thermal-fluid performance with heat transfer enhancements between 38-54% and pressure penalties between 42-56%, resulting in peak PEC of 1.81 at Re = 1400an 81% improvement over the conventional straight fin. The more aggressive TF33 knockoff produced higher heat transfer enhancement values (45-62%) with unacceptably high-pressure penalties (68-85%), while the intermediate TF77 knockoff provided only marginal increments (28-42%) with modest pressure penalties (25-35%). The results indicated that the formation of the secondary flow and disturbance to the thermal boundary layer are the main mechanisms responsible for heat transfer augmentation, and the 0.55 twist ratio represents the best tradeoff between the effect of thermal mixing enhancement and hydraulic pumping power consumption. This study is aimed at the development of compact heat exchanger designs, which are of relevance for high-efficiency and space-limited applications.
- Open Access
- 10 May 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 131 (1) , 20-30
Technical-Economic and Thermal Analysis of New Combined Renewable Energy Systems for Off-Grid Agriculture: A Numerical Study
A large part of the people who do not have access to electric energy are in rural areas, and this lack of access to energy causes the lack of development in these areas and the reduction of public welfare. Therefore, in the present study, a method for providing the electrical energy required in the agricultural sector independently of the grid using a photovoltaic + battery system is discussed from different technical and economic perspectives. For this purpose, the detailed knowledge of the various components of the proposed system and the mathematical relationships that govern it are first discussed. Considering the importance of economic analysis in the design of a system, in this study, a method for checking the life cycle costs of the system components is proposed according to the lifetime of the components, investment costs, maintenance costs and discount rate. Finally, to check the effectiveness of the proposed method, a sample agricultural farm with specific electrical loads was selected in the city of Baghdad-Iraq. In the design of the proposed photovoltaic + battery system, 10 270 watt modules of Yingli model - YL270P-29b with a nominal capacity of 2.7 kW were used to supply the desired electric loads. In addition, a battery with a capacity of 15.66 kilowatt-hours was used to provide electrical loads in non-sunny hours of the day and to improve the performance of the photovoltaic system in sunny hours. The obtained results showed that in a photovoltaic + battery system, the use of a combination of direct current and alternating current loads can bring the most economic savings for the subscriber.
- 10 May 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 131 (1) , 20-30
Open AccessTechnical-Economic and Thermal Analysis of New Combined Renewable Energy Systems for Off-Grid Agriculture: A Numerical Study
A large part of the people who do not have access to electric energy are in rural areas, and this lack of access to energy causes the lack of development in these areas and the reduction of public welfare. Therefore, in the present study, a method for providing the electrical energy required in the agricultural sector independently of the grid using a photovoltaic + battery system is discussed from different technical and economic perspectives. For this purpose, the detailed knowledge of the various components of the proposed system and the mathematical relationships that govern it are first discussed. Considering the importance of economic analysis in the design of a system, in this study, a method for checking the life cycle costs of the system components is proposed according to the lifetime of the components, investment costs, maintenance costs and discount rate. Finally, to check the effectiveness of the proposed method, a sample agricultural farm with specific electrical loads was selected in the city of Baghdad-Iraq. In the design of the proposed photovoltaic + battery system, 10 270 watt modules of Yingli model - YL270P-29b with a nominal capacity of 2.7 kW were used to supply the desired electric loads. In addition, a battery with a capacity of 15.66 kilowatt-hours was used to provide electrical loads in non-sunny hours of the day and to improve the performance of the photovoltaic system in sunny hours. The obtained results showed that in a photovoltaic + battery system, the use of a combination of direct current and alternating current loads can bring the most economic savings for the subscriber.
- Open Access
- 30 January 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 29 (1) , 16-26
Optimizing Air Flow and Temperature Distribution in a Greenhouse Solar Dryer Using Computational Fluid Dynamics
This research is conducted to optimize the uniformity of air flow and temperature distribution for a greenhouse solar dryer based on Computational Fluid Dynamics (CFD) simulations. But the aim was to maximise drying efficiency, which could only be achieved by ensuring that there was a uniform air velocity — and temperature, for some applications — throughout the whole volume of the drying chamber. The basic idea is to model and simulating several fan configurations such as horizontal flow fans (with grilles), without grille, or even vertical flow fans. The results revealed that the (horizontal-flow/fan/grille) system also improved air distribution, leading to steadier temperature field and higher average air velocity when compared with other configurations. The peak air velocity at the inlet of drying zone for optimized model is observed to be 3.8 m/s, with an average temperature in the drying zone is 320 K which led to better drying efficiency and faster dry times. The results of this study should be useful to the optimal designing and operating greenhouse solar dryers whilst aiming for a sustainable and energy-efficient way forward in food preservation methods.
- 30 January 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 29 (1) , 16-26
Open AccessOptimizing Air Flow and Temperature Distribution in a Greenhouse Solar Dryer Using Computational Fluid Dynamics
This research is conducted to optimize the uniformity of air flow and temperature distribution for a greenhouse solar dryer based on Computational Fluid Dynamics (CFD) simulations. But the aim was to maximise drying efficiency, which could only be achieved by ensuring that there was a uniform air velocity — and temperature, for some applications — throughout the whole volume of the drying chamber. The basic idea is to model and simulating several fan configurations such as horizontal flow fans (with grilles), without grille, or even vertical flow fans. The results revealed that the (horizontal-flow/fan/grille) system also improved air distribution, leading to steadier temperature field and higher average air velocity when compared with other configurations. The peak air velocity at the inlet of drying zone for optimized model is observed to be 3.8 m/s, with an average temperature in the drying zone is 320 K which led to better drying efficiency and faster dry times. The results of this study should be useful to the optimal designing and operating greenhouse solar dryers whilst aiming for a sustainable and energy-efficient way forward in food preservation methods.
- Open Access
- 30 September 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (2) , 43-59
Studying How the Size of Energy Storage Tanks with Sodium Nitrate Affects Their Performance
Energy storage serves the dual purpose of narrowing the disparity between energy provision and consumption while also enhancing the efficiency and dependability of energy generation systems, thereby assuming a crucial position in energy storage. This technology reduces expenses by gathering and using wasted energy. Thermal energy storage using phase transition materials is a highly regarded technology in thermal energy storage. Studying energy storage tanks that incorporate phase transition material is a novel area of research in the energy world. Sodium nitrate is the PCM material employed in this study. This discussion focuses on the influence of the alumina percentage and tank dimensions on the behavior of molten sodium nitrate over time. This analysis incorporates the influence of the diameter-to-length ratio based on the Grashof number. Consequently, ten different dimensional states of the tank are taken into account. This study discusses the findings from analyzing energy storage tanks incorporating phase change material using Ansys Fluent software. To achieve this objective, the initial step involves presenting the ratio between the required dimensions and the Gershoff numbers acquired for various diameters. Subsequently, the mesh convergence process and the solution's independence from the grid are explained. Subsequently, he showstate d the outlines of the aqueous portion and the temperature derived from the study, culminating in presenting the findings. The temperature distribution inside the tank becomes increasingly homogeneous by augmenting the proportion of alumina included in sodium nitrate. The addition of alumina particles to sodium nitrate has a diminishing impact as the height-to-diameter ratio of the tank is reduced. As the tank transitions from state 1 to state 7, whose diameter and height are identical, the curvature of the temperature change graphs diminishes. This drop signifies a reduction in the rate at which the phase-change material melts.
- 30 September 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (2) , 43-59
Open AccessStudying How the Size of Energy Storage Tanks with Sodium Nitrate Affects Their Performance
Energy storage serves the dual purpose of narrowing the disparity between energy provision and consumption while also enhancing the efficiency and dependability of energy generation systems, thereby assuming a crucial position in energy storage. This technology reduces expenses by gathering and using wasted energy. Thermal energy storage using phase transition materials is a highly regarded technology in thermal energy storage. Studying energy storage tanks that incorporate phase transition material is a novel area of research in the energy world. Sodium nitrate is the PCM material employed in this study. This discussion focuses on the influence of the alumina percentage and tank dimensions on the behavior of molten sodium nitrate over time. This analysis incorporates the influence of the diameter-to-length ratio based on the Grashof number. Consequently, ten different dimensional states of the tank are taken into account. This study discusses the findings from analyzing energy storage tanks incorporating phase change material using Ansys Fluent software. To achieve this objective, the initial step involves presenting the ratio between the required dimensions and the Gershoff numbers acquired for various diameters. Subsequently, the mesh convergence process and the solution's independence from the grid are explained. Subsequently, he showstate d the outlines of the aqueous portion and the temperature derived from the study, culminating in presenting the findings. The temperature distribution inside the tank becomes increasingly homogeneous by augmenting the proportion of alumina included in sodium nitrate. The addition of alumina particles to sodium nitrate has a diminishing impact as the height-to-diameter ratio of the tank is reduced. As the tank transitions from state 1 to state 7, whose diameter and height are identical, the curvature of the temperature change graphs diminishes. This drop signifies a reduction in the rate at which the phase-change material melts.
- Open Access
- 30 March 2024
- Published by IFHAN in International Journal of Corrosion and Scale Inhibition
- Vol. 13 (1)
N-Phenyl-N′-[5-phenyl-1,2,4-thiadiazol-3-yl]thiourea: corrosion inhibition of mild steel in 1 M HCl
- 30 March 2024
- Published by IFHAN in International Journal of Corrosion and Scale Inhibition
- Vol. 13 (1)
Open AccessN-Phenyl-N′-[5-phenyl-1,2,4-thiadiazol-3-yl]thiourea: corrosion inhibition of mild steel in 1 M HCl
- Open Access
- 8 January 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 111 (2) , 154-169
Empirical Investigation of Thermal Features of Phase Change Material as Thermal Storage System
This paper presents an empirical investigation of the melting processes of phase change material (PCM) in a tube and shell heating exchanger utilizing solar thermal energy. The experiments were conducted outdoors in Al-Mussaib city, Babylon, Iraq (Lat 32.5° North, long 44.3° East), utilizing a north-south (N-S) collector oriented at a tilt angle of 32.5° from the horizontal. This work utilized pure Iraqi black paraffin with 12 kg as PCM. The main empirical rig involves a vacuum tube solar collector (VTSC) utilizing a tube and shell heating exchanger to melt PCM in the shell regime. Different rates of water flow inside the internal heating exchanger's tube, namely (3.5, 5, and 8.5 L/m), were utilized for each season from August 2022 to January 2023. The empirical findings concluded that the internal tube inlet and surrounding temps significantly influence the melting process compared to the rates of water flow. It was found that the melting process of PCM needs about (3 to 4) hours in the summer season. Still, winter needs a longer time, about 14 to 16 hours. Increasing surrounding temp and solar radiation reduces the melting time of phase-change material. The findings of the present work were compared with the earlier investigations and agree with increasing the present work by 23.5 %. The findings from the present study are of practical importance for industries requiring storage materials to improve thermal storage system performance.
- 8 January 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 111 (2) , 154-169
Open AccessEmpirical Investigation of Thermal Features of Phase Change Material as Thermal Storage System
This paper presents an empirical investigation of the melting processes of phase change material (PCM) in a tube and shell heating exchanger utilizing solar thermal energy. The experiments were conducted outdoors in Al-Mussaib city, Babylon, Iraq (Lat 32.5° North, long 44.3° East), utilizing a north-south (N-S) collector oriented at a tilt angle of 32.5° from the horizontal. This work utilized pure Iraqi black paraffin with 12 kg as PCM. The main empirical rig involves a vacuum tube solar collector (VTSC) utilizing a tube and shell heating exchanger to melt PCM in the shell regime. Different rates of water flow inside the internal heating exchanger's tube, namely (3.5, 5, and 8.5 L/m), were utilized for each season from August 2022 to January 2023. The empirical findings concluded that the internal tube inlet and surrounding temps significantly influence the melting process compared to the rates of water flow. It was found that the melting process of PCM needs about (3 to 4) hours in the summer season. Still, winter needs a longer time, about 14 to 16 hours. Increasing surrounding temp and solar radiation reduces the melting time of phase-change material. The findings of the present work were compared with the earlier investigations and agree with increasing the present work by 23.5 %. The findings from the present study are of practical importance for industries requiring storage materials to improve thermal storage system performance.
- Open Access
- 30 June 2023
- Published by International Information and Engineering Technology Association in International Journal of Heat and Technology
- Vol. 41 (3) , 780-788
Enhancement of Plate-Fin Heat Exchanger Performance with Aid of (RWP) Vortex Generator
- 30 June 2023
- Published by International Information and Engineering Technology Association in International Journal of Heat and Technology
- Vol. 41 (3) , 780-788
Open AccessEnhancement of Plate-Fin Heat Exchanger Performance with Aid of (RWP) Vortex Generator
- Open Access
- 29 May 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (7) , 131-147
Improvement of Plate-Fin Heat Exchanger Performance with Assistance of Various Types of Vortex Generator
A 3-dimensional incompressible laminar flow and heat-transfer in a plate-fin heat exchanger (PFHE) where investigated numerically in this article. The influence of mounting a longitudinal vortex generator (LVG) on the offset rectangular-triangular fin (ORT) in the PFHE, on thermal and hydro-dynamic fields are presented. The novelty of this study is by attaching a LVG to an offset strip fin (OSF) surface. The cases of study for the PFHE are established, by using a built-in rectangular winglet pair type RWP longitudinal vortex generator carried out and fitted on this fin to improve the convective heat transfer of the (ORT) fin while minimizing pressure loss. The upper and lower plates are exposed to constant heat flux and the working fluid is air where chosen under a laminar range of RE (600 to 1400). The laminar flow and heat-transfer are governed by continuity, momentum and energy equations. ANSYS FLUENT (2021 R1) is used to get the numerical results, based on the finite volume method. The performance of the VG is assessed for an optimum winglet attack angle (45°), as well as by modifying the geometrical size parameters, namely the height and placement (L) of the RWP LVG. The result shows that the Nusselt number reaches its optimum enhancement values by using a common flow up CFU built-in rectangular winglet pair type RWP VG with a height and entrance length of (h=1.25mm, L=0.5mm), by 22.23% as compared with base case configuration (ORT). Finally, a two more LVG are tested with the optimum conditions of the RWP, which they are a delta winglet pair (DWP) and trapezoidal winglet pair (TWP). In addition, the temperature fields for the primary and secondary flows were shown in contour and streamline diagrams
- 29 May 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (7) , 131-147
Open AccessImprovement of Plate-Fin Heat Exchanger Performance with Assistance of Various Types of Vortex Generator
A 3-dimensional incompressible laminar flow and heat-transfer in a plate-fin heat exchanger (PFHE) where investigated numerically in this article. The influence of mounting a longitudinal vortex generator (LVG) on the offset rectangular-triangular fin (ORT) in the PFHE, on thermal and hydro-dynamic fields are presented. The novelty of this study is by attaching a LVG to an offset strip fin (OSF) surface. The cases of study for the PFHE are established, by using a built-in rectangular winglet pair type RWP longitudinal vortex generator carried out and fitted on this fin to improve the convective heat transfer of the (ORT) fin while minimizing pressure loss. The upper and lower plates are exposed to constant heat flux and the working fluid is air where chosen under a laminar range of RE (600 to 1400). The laminar flow and heat-transfer are governed by continuity, momentum and energy equations. ANSYS FLUENT (2021 R1) is used to get the numerical results, based on the finite volume method. The performance of the VG is assessed for an optimum winglet attack angle (45°), as well as by modifying the geometrical size parameters, namely the height and placement (L) of the RWP LVG. The result shows that the Nusselt number reaches its optimum enhancement values by using a common flow up CFU built-in rectangular winglet pair type RWP VG with a height and entrance length of (h=1.25mm, L=0.5mm), by 22.23% as compared with base case configuration (ORT). Finally, a two more LVG are tested with the optimum conditions of the RWP, which they are a delta winglet pair (DWP) and trapezoidal winglet pair (TWP). In addition, the temperature fields for the primary and secondary flows were shown in contour and streamline diagrams