Rui Shi
Rui Shi has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Chung-Kuan Cheng
CSE Dept., Univ. of California San Diego, 9500 Gilman Drive, La Jolla, CA 92093-0404. Tel: 1-858-534-8174, Fax: 1-858-534-7029
2 shared publications - Haikun Zhu
CSE Dept., Univ. of California San Diego, 9500 Gilman Drive, La Jolla, CA 92093-0404. Tel: 1-858-534-8174, Fax: 1-858-534-7029
2 shared publications Alina Deutsch
IBM T.J. Watson Research Center, Yorktown Heights, NY 10598
1 shared publication- Chung-Kuan Cheng
University of California, San Diego, La Jolla, CA, USA
1 shared publication George Katopis
IBM Enterprise System Group, Poughkeepsie, NY 12601
1 shared publication- Hongyu Chen
Synopsys Inc., Mountain View, CA, USA
1 shared publication
Latest Publications
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 684-689
Approaching Speed-of-light Distortionless Communication for On-chip Interconnect
We extend the surfliner on-chip distortionless transmission line scheme and provide more details for the implementation issues. Surfliner seeks to approach distortionless transmission by intentionally adding shunt resistors between the signal line and the ground. In theory if we distributively make the shunt conductance G=RC/L, there is no distortion at the receiver end and the signal propagates at the speed of light. We show the feasibility and advantages of this shunt resistor scheme by a real design case of single-ended microstrip line in 0.10mum technology. The simulation results indicate we can achieve near perfect signaling of 10 Gbps data over a 10 mm serial link, yet no pre-emphasis/equalization or other special techniques are needed. Guidelines for determining the optimal value and spacing of the shunt resistors are also provided.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 684-689
Approaching Speed-of-light Distortionless Communication for On-chip Interconnect
We extend the surfliner on-chip distortionless transmission line scheme and provide more details for the implementation issues. Surfliner seeks to approach distortionless transmission by intentionally adding shunt resistors between the signal line and the ground. In theory if we distributively make the shunt conductance G=RC/L, there is no distortion at the receiver end and the signal propagates at the speed of light. We show the feasibility and advantages of this shunt resistor scheme by a real design case of single-ended microstrip line in 0.10mum technology. The simulation results indicate we can achieve near perfect signaling of 10 Gbps data over a 10 mm serial link, yet no pre-emphasis/equalization or other special techniques are needed. Guidelines for determining the optimal value and spacing of the shunt resistors are also provided.
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 2006 IEEE/ACM International Conference on Computer Aided Design
- No. 10923152,p. 815-819
Layer Minimization of Escape Routing in Area Array Packaging
We devise a central triangular sequence to minimize the escape routing layers in area array packaging. We use a network flow model to analyze the bottleneck of the routable pins. The triangular patterns are generated in a reverse order from the last to the first layer. We demonstrate that the triangular pin sequence maximizes the sum of escape pins in the accumulated layers and thus minimize the number of escape routing layers. A test case is presented to illustrate the approach
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 2006 IEEE/ACM International Conference on Computer Aided Design
- No. 10923152,p. 815-819
Layer Minimization of Escape Routing in Area Array Packaging
We devise a central triangular sequence to minimize the escape routing layers in area array packaging. We use a network flow model to analyze the bottleneck of the routable pins. The triangular patterns are generated in a reverse order from the last to the first layer. We demonstrate that the triangular pin sequence maximizes the sum of escape pins in the accumulated layers and thus minimize the number of escape routing layers. A test case is presented to illustrate the approach
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21654107,p. 175-178
Distortion Minimization for Packaging Level Interconnects
We propose a novel high-speed serial signaling scheme that minimizes the distortion for multichip module (MCM) packaging level communication by intentionally adding leakage resistors between the signal trace and the ground. The new scheme is inspired by the theory of distortionless transmission line which states that if R/G = L/C, there will be no distortion at the receiver end and the signal propagates at the speed of light. The simulation results indicate that, using the shunt resistor scheme, 10+ Gbps bit rate is achievable over a 10 cm single-ended stripline without pre-emphasis or equalization
- 1 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21654107,p. 175-178
Distortion Minimization for Packaging Level Interconnects
We propose a novel high-speed serial signaling scheme that minimizes the distortion for multichip module (MCM) packaging level communication by intentionally adding leakage resistors between the signal trace and the ground. The new scheme is inspired by the theory of distortionless transmission line which states that if R/G = L/C, there will be no distortion at the receiver end and the signal propagates at the speed of light. The simulation results indicate that, using the shunt resistor scheme, 10+ Gbps bit rate is achievable over a 10 cm single-ended stripline without pre-emphasis or equalization