A. V. Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
A. V. Kim has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Igor Yu. Litovchenko
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Science, Tomsk, Russian Federation
16 shared publications - Sergey A. Akkuzin
Panin Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences (ISPMS SB RAS), Tomsk 634055, Russia
15 shared publications - Nadezhda Polekhina
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Science, Tomsk, Russian Federation
14 shared publications - Kseniya Spiridonova
Institute of Strength Physics and Materials Science of the Siberian Branch, Russian Academy of Sciences, Tomsk, Russian Federation
7 shared publications - Vyacheslav M. Chernov
Bochvar High-Technology Research Institute for Inorganic Materials, Moscow, Russia
7 shared publications - Evgeny Moskvichev
Institute of Strength Physics and Materials Science, Siberian Branch of Russian Academy of Sciences, 634055 Tomsk, Russia
4 shared publications
Latest Publications
- Open Access
- 8 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 126
The Effect of Structural States on the Microstructure and Mechanical Properties of Low-Activation Austenitic Steel After Long-Term Thermal Exposure at 700 °C
The microstructure of a high-manganese low-activation austenitic steel after aging for 500 and 1000 h at 700 °C was investigated using transmission and scanning electron microscopy. Two structural states were examined: cold rolling (CR) and high-temperature thermomechanical treatment (HTMT). After CR, aging leads to the precipitation of dispersed M23C6 carbides (M = Cr, W), primarily along grain and deformation twin boundaries. After HTMT, these particles are mainly localized at grain and low-angle boundaries. With increasing aging time, both the size and volume fraction of the particles increase. In both states, the microtwin and substructure are partially retained after aging. Local regions corresponding to the early stages of recrystallization were identified after both treatments. These regions were associated with intense decomposition of the supersaturated solid solution and the coarsening of carbide particles. The mechanical properties were evaluated by tensile testing at 20, 650, and 700 °C. Aging reduced average ductility after both treatments and at all test temperatures, with this trend persisting with increasing aging time. After CR and aging, a significant scatter in elongation to failure was observed, with minimum values of ≈2–3%. This behavior is attributed to the high density of plate-like M23C6 carbides at grain and microtwin boundaries. Microcrack formation and intercrystalline fracture features were observed, directly linked to the high density of boundary carbides. These effects were less pronounced in the HTMT condition after aging. In this paper, strategies for suppressing carbide precipitation in high-manganese low-activation austenitic steels via chemical composition and thermomechanical processing optimization are discussed.
- 8 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 126
Open AccessThe Effect of Structural States on the Microstructure and Mechanical Properties of Low-Activation Austenitic Steel After Long-Term Thermal Exposure at 700 °C
The microstructure of a high-manganese low-activation austenitic steel after aging for 500 and 1000 h at 700 °C was investigated using transmission and scanning electron microscopy. Two structural states were examined: cold rolling (CR) and high-temperature thermomechanical treatment (HTMT). After CR, aging leads to the precipitation of dispersed M23C6 carbides (M = Cr, W), primarily along grain and deformation twin boundaries. After HTMT, these particles are mainly localized at grain and low-angle boundaries. With increasing aging time, both the size and volume fraction of the particles increase. In both states, the microtwin and substructure are partially retained after aging. Local regions corresponding to the early stages of recrystallization were identified after both treatments. These regions were associated with intense decomposition of the supersaturated solid solution and the coarsening of carbide particles. The mechanical properties were evaluated by tensile testing at 20, 650, and 700 °C. Aging reduced average ductility after both treatments and at all test temperatures, with this trend persisting with increasing aging time. After CR and aging, a significant scatter in elongation to failure was observed, with minimum values of ≈2–3%. This behavior is attributed to the high density of plate-like M23C6 carbides at grain and microtwin boundaries. Microcrack formation and intercrystalline fracture features were observed, directly linked to the high density of boundary carbides. These effects were less pronounced in the HTMT condition after aging. In this paper, strategies for suppressing carbide precipitation in high-manganese low-activation austenitic steels via chemical composition and thermomechanical processing optimization are discussed.
- Open Access
- 31 March 2026
- Published by Togliatti State University in Frontier materials & technologies
- No. 74,p. 19-26
The effect of aging at 700°C on the microstructure and mechanical properties of high-nitrogen austenitic steel
Problem. Prolonged annealing of high-nitrogen austenitic steels leads to the precipitation of secondary phases, which significantly affects the structure and properties of the material. However, the nature of phase precipitates and their influence on the mechanical properties of VNS-53-Sh steel have been insufficiently studied. Aim. The aim of this work is to investigate the effect of long-term annealing at 700 °C on the microstructure and mechanical properties of VNS53-Sh high-nitrogen austenitic steel and to determine the phase composition and characteristics of the formed secondary phases. Methods. VNS-53-Sh steel samples were subjected to annealing at 700 °C for 100 hours. Microstructural investigation was carried out using optical metallography, scanning and transmission electron microscopy with a quantitative assessment of the secondary phase fraction. Mechanical properties were determined by uniaxial tensile testing followed by analysis of changes in strength and ductility characteristics. Results. After annealing, grain-boundary and intragranular precipitates of M23C6-type carbides were revealed, formed by the discontinuous austenite decomposition mechanism. Estimates of the area occupied by carbides give values of less than 5 %. Meanwhile, the proportion of a pearlite-like structure represented by lamellar particles and a chromium-depleted matrix is approximately 23 %. The yield strength decreases by 111 MPa, the ultimate tensile strength – by 62 MPa, and the relative elongation increases by about 7 %. Conclusions. Long-term annealing of VNS-53-Sh steel at 700 °C leads to the formation of M23C6 carbide precipitates and partial relaxation of the dislocation structure, which is accompanied by a moderate reduction in strength properties while simultaneously increasing the ductility of the material.
- 31 March 2026
- Published by Togliatti State University in Frontier materials & technologies
- No. 74,p. 19-26
Open AccessThe effect of aging at 700°C on the microstructure and mechanical properties of high-nitrogen austenitic steel
Problem. Prolonged annealing of high-nitrogen austenitic steels leads to the precipitation of secondary phases, which significantly affects the structure and properties of the material. However, the nature of phase precipitates and their influence on the mechanical properties of VNS-53-Sh steel have been insufficiently studied. Aim. The aim of this work is to investigate the effect of long-term annealing at 700 °C on the microstructure and mechanical properties of VNS53-Sh high-nitrogen austenitic steel and to determine the phase composition and characteristics of the formed secondary phases. Methods. VNS-53-Sh steel samples were subjected to annealing at 700 °C for 100 hours. Microstructural investigation was carried out using optical metallography, scanning and transmission electron microscopy with a quantitative assessment of the secondary phase fraction. Mechanical properties were determined by uniaxial tensile testing followed by analysis of changes in strength and ductility characteristics. Results. After annealing, grain-boundary and intragranular precipitates of M23C6-type carbides were revealed, formed by the discontinuous austenite decomposition mechanism. Estimates of the area occupied by carbides give values of less than 5 %. Meanwhile, the proportion of a pearlite-like structure represented by lamellar particles and a chromium-depleted matrix is approximately 23 %. The yield strength decreases by 111 MPa, the ultimate tensile strength – by 62 MPa, and the relative elongation increases by about 7 %. Conclusions. Long-term annealing of VNS-53-Sh steel at 700 °C leads to the formation of M23C6 carbide precipitates and partial relaxation of the dislocation structure, which is accompanied by a moderate reduction in strength properties while simultaneously increasing the ductility of the material.
- 8 December 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (6) , 1980-1986
Structural Phase State, Martensitic Transformations and Inelastic Properties of TiNi-based Alloy Fabricated by Electron Beam Wire-Feed Additive Manufacturing
In this paper, the structural phase state, martensitic transformation temperatures, and inelastic properties of a TiNi-based alloy obtained by electron beam wire-feed additive manufacturing (EBAM) on a Ti49.8Ni50.2 (at %) substrate were studied. It was shown that the printed samples had an inhomogeneous coarse-grained microstructure both in the direction perpendicular and parallel to the substrate. The microstructure type of the samples obtained by EBAM depends on the distance from the substrate and is determined by the cooling conditions in the vacuum chamber of the setup for 20 h from 800°C. At room temperature, the obtained samples had a high-temperature B2-phase structure. It was established that the printed samples underwent a B2 ↔ B19' martensitic transformation upon cooling and heating. It was shown that the studied samples exhibit a superelasticity of 9.01% under torsion with an accumulated plastic strain of 1.28% (including 5.78% in the absence of plastic deformation).
- 8 December 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (6) , 1980-1986
Structural Phase State, Martensitic Transformations and Inelastic Properties of TiNi-based Alloy Fabricated by Electron Beam Wire-Feed Additive Manufacturing
In this paper, the structural phase state, martensitic transformation temperatures, and inelastic properties of a TiNi-based alloy obtained by electron beam wire-feed additive manufacturing (EBAM) on a Ti49.8Ni50.2 (at %) substrate were studied. It was shown that the printed samples had an inhomogeneous coarse-grained microstructure both in the direction perpendicular and parallel to the substrate. The microstructure type of the samples obtained by EBAM depends on the distance from the substrate and is determined by the cooling conditions in the vacuum chamber of the setup for 20 h from 800°C. At room temperature, the obtained samples had a high-temperature B2-phase structure. It was established that the printed samples underwent a B2 ↔ B19' martensitic transformation upon cooling and heating. It was shown that the studied samples exhibit a superelasticity of 9.01% under torsion with an accumulated plastic strain of 1.28% (including 5.78% in the absence of plastic deformation).
- 11 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (15) , 14638-14648
Microstructure and Mechanical Properties of High-Nitrogen Austenitic Steel after High-Temperature Thermomechanical Treatment by Hot Rolling
- 11 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (15) , 14638-14648
Microstructure and Mechanical Properties of High-Nitrogen Austenitic Steel after High-Temperature Thermomechanical Treatment by Hot Rolling
- 1 November 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (11) , 1948-1955
Microstructure and mechanical properties of cold-deformed low-activation chromium-manganese austenitic steel after annealing at 900 °C
- 1 November 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (11) , 1948-1955
Microstructure and mechanical properties of cold-deformed low-activation chromium-manganese austenitic steel after annealing at 900 °C
- 1 October 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (10) , 1665-1672
Microstructure and microhardness of 12% chromium ferritic-martensitic steel sintered from elemental powders
- 1 October 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (10) , 1665-1672
Microstructure and microhardness of 12% chromium ferritic-martensitic steel sintered from elemental powders
- 30 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (24) , 29791-29802
Effect of Multi-pass Warm Rolling and Annealing on Microstructure and Mechanical Properties of an Austenitic Steel
- 30 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (24) , 29791-29802
Effect of Multi-pass Warm Rolling and Annealing on Microstructure and Mechanical Properties of an Austenitic Steel
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Phase transformation during in situ heating of low-activation austenitic steel
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Phase transformation during in situ heating of low-activation austenitic steel
- 6 January 2025
- Published by Elsevier in Materialia
- Vol. 39
Effect of aging at 700 °C on the microstructure, phase transformations, and mechanical properties of low-activation austenitic steel
- 6 January 2025
- Published by Elsevier in Materialia
- Vol. 39
Effect of aging at 700 °C on the microstructure, phase transformations, and mechanical properties of low-activation austenitic steel
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Annealing effect on structure, phase composition and mechanical properties of high-nitrogen austenitic steel
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Annealing effect on structure, phase composition and mechanical properties of high-nitrogen austenitic steel