Kseniya Spiridonova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kseniya Spiridonova has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Igor Yu. Litovchenko
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Science, Tomsk, Russian Federation
12 shared publications - Nadezhda Polekhina
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Science, Tomsk, Russian Federation
12 shared publications - Sergey A. Akkuzin
Panin Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences (ISPMS SB RAS), Tomsk 634055, Russia
11 shared publications - Vyacheslav M. Chernov
Bochvar High-Technology Research Institute for Inorganic Materials, Moscow, Russia
9 shared publications - A. V. Kim
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Science, Tomsk, Russian Federation
7 shared publications - Valeria Linnik
Institute of Strength Physics and Materials Science SB RAS, 2/4 pr. Akademicheskii, 634055 Tomsk, Russia
5 shared publications
Latest Publications
- Open Access
- 8 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 126
The Effect of Structural States on the Microstructure and Mechanical Properties of Low-Activation Austenitic Steel After Long-Term Thermal Exposure at 700 °C
The microstructure of a high-manganese low-activation austenitic steel after aging for 500 and 1000 h at 700 °C was investigated using transmission and scanning electron microscopy. Two structural states were examined: cold rolling (CR) and high-temperature thermomechanical treatment (HTMT). After CR, aging leads to the precipitation of dispersed M23C6 carbides (M = Cr, W), primarily along grain and deformation twin boundaries. After HTMT, these particles are mainly localized at grain and low-angle boundaries. With increasing aging time, both the size and volume fraction of the particles increase. In both states, the microtwin and substructure are partially retained after aging. Local regions corresponding to the early stages of recrystallization were identified after both treatments. These regions were associated with intense decomposition of the supersaturated solid solution and the coarsening of carbide particles. The mechanical properties were evaluated by tensile testing at 20, 650, and 700 °C. Aging reduced average ductility after both treatments and at all test temperatures, with this trend persisting with increasing aging time. After CR and aging, a significant scatter in elongation to failure was observed, with minimum values of ≈2–3%. This behavior is attributed to the high density of plate-like M23C6 carbides at grain and microtwin boundaries. Microcrack formation and intercrystalline fracture features were observed, directly linked to the high density of boundary carbides. These effects were less pronounced in the HTMT condition after aging. In this paper, strategies for suppressing carbide precipitation in high-manganese low-activation austenitic steels via chemical composition and thermomechanical processing optimization are discussed.
- 8 April 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (4) , 126
Open AccessThe Effect of Structural States on the Microstructure and Mechanical Properties of Low-Activation Austenitic Steel After Long-Term Thermal Exposure at 700 °C
The microstructure of a high-manganese low-activation austenitic steel after aging for 500 and 1000 h at 700 °C was investigated using transmission and scanning electron microscopy. Two structural states were examined: cold rolling (CR) and high-temperature thermomechanical treatment (HTMT). After CR, aging leads to the precipitation of dispersed M23C6 carbides (M = Cr, W), primarily along grain and deformation twin boundaries. After HTMT, these particles are mainly localized at grain and low-angle boundaries. With increasing aging time, both the size and volume fraction of the particles increase. In both states, the microtwin and substructure are partially retained after aging. Local regions corresponding to the early stages of recrystallization were identified after both treatments. These regions were associated with intense decomposition of the supersaturated solid solution and the coarsening of carbide particles. The mechanical properties were evaluated by tensile testing at 20, 650, and 700 °C. Aging reduced average ductility after both treatments and at all test temperatures, with this trend persisting with increasing aging time. After CR and aging, a significant scatter in elongation to failure was observed, with minimum values of ≈2–3%. This behavior is attributed to the high density of plate-like M23C6 carbides at grain and microtwin boundaries. Microcrack formation and intercrystalline fracture features were observed, directly linked to the high density of boundary carbides. These effects were less pronounced in the HTMT condition after aging. In this paper, strategies for suppressing carbide precipitation in high-manganese low-activation austenitic steels via chemical composition and thermomechanical processing optimization are discussed.
- 28 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (17) , 17044-17059
Effect of Long-Term Aging at 580 °C on Microstructure and Mechanical Properties of 12% Chromium Heat-Resistant Ferritic–Martensitic Steel
- 28 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (17) , 17044-17059
Effect of Long-Term Aging at 580 °C on Microstructure and Mechanical Properties of 12% Chromium Heat-Resistant Ferritic–Martensitic Steel
- 1 November 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (11) , 1948-1955
Microstructure and mechanical properties of cold-deformed low-activation chromium-manganese austenitic steel after annealing at 900 °C
- 1 November 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (11) , 1948-1955
Microstructure and mechanical properties of cold-deformed low-activation chromium-manganese austenitic steel after annealing at 900 °C
- 30 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (24) , 29791-29802
Effect of Multi-pass Warm Rolling and Annealing on Microstructure and Mechanical Properties of an Austenitic Steel
- 30 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (24) , 29791-29802
Effect of Multi-pass Warm Rolling and Annealing on Microstructure and Mechanical Properties of an Austenitic Steel
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Phase transformation during in situ heating of low-activation austenitic steel
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Phase transformation during in situ heating of low-activation austenitic steel
- 6 January 2025
- Published by Elsevier in Materialia
- Vol. 39
Effect of aging at 700 °C on the microstructure, phase transformations, and mechanical properties of low-activation austenitic steel
- 6 January 2025
- Published by Elsevier in Materialia
- Vol. 39
Effect of aging at 700 °C on the microstructure, phase transformations, and mechanical properties of low-activation austenitic steel
- Open Access
- 21 December 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (6) , 716-724
Impact strength and fracture features of 12 % chromium ferritic-martensitic steel EP-823 in temperature range from –196 to 100 °С
The authors investigated the patterns of fracture during impact bending tests and determined the values of impact strength and temperature of the ductile-brittle transition in temperature range from –196 to 100 °С of heat-resistant 12 % chromium ferritic-martensitic steel EP-823 in structural states after traditional heat (THT) and high-temperature thermomechanical (TMT) treatments. After THT, temperature of the ductile-brittle transition Tdbt is approximately –45 °С, after HTMT – approximately –40 °С. At these temperatures, the impact energy (KCV) after THT is approximately 36 J/cm2, after HTMT – 32 J/cm2. Fractographic studies conducted by scanning electron microscopy of the fracture features of impact steel samples after two treatments (THT and HTMT) in the low-temperature test area (at cryogenic temperatures) showed a predominantly brittle nature of fracture, while fracture occurs by the mechanism of a transcrystalline quasi-cleavage. In the temperature range of the ductile-brittle transition, a mixed nature of fracture is observed, which passes through the mechanism of a transcrystalline quasi-cleavage with elements of ductile dimple fracture. In the temperature range from 50 to 100 °С, the extremely ductile nature of the fracture was detected, realized by the transcrystalline dimple fracture mechanism. After HTMT, there is a slight decrease (relative to THT) in the steel impact strength in almost the entire temperature range under consideration and, accordingly, an increase in the temperature of its ductile-brittle transition. This is due to the tests’ geometry, in which the direction of impact occurs in the plane of the layered structure, and it facilitates the formation of delamination cracks.
- 21 December 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (6) , 716-724
Open AccessImpact strength and fracture features of 12 % chromium ferritic-martensitic steel EP-823 in temperature range from –196 to 100 °С
The authors investigated the patterns of fracture during impact bending tests and determined the values of impact strength and temperature of the ductile-brittle transition in temperature range from –196 to 100 °С of heat-resistant 12 % chromium ferritic-martensitic steel EP-823 in structural states after traditional heat (THT) and high-temperature thermomechanical (TMT) treatments. After THT, temperature of the ductile-brittle transition Tdbt is approximately –45 °С, after HTMT – approximately –40 °С. At these temperatures, the impact energy (KCV) after THT is approximately 36 J/cm2, after HTMT – 32 J/cm2. Fractographic studies conducted by scanning electron microscopy of the fracture features of impact steel samples after two treatments (THT and HTMT) in the low-temperature test area (at cryogenic temperatures) showed a predominantly brittle nature of fracture, while fracture occurs by the mechanism of a transcrystalline quasi-cleavage. In the temperature range of the ductile-brittle transition, a mixed nature of fracture is observed, which passes through the mechanism of a transcrystalline quasi-cleavage with elements of ductile dimple fracture. In the temperature range from 50 to 100 °С, the extremely ductile nature of the fracture was detected, realized by the transcrystalline dimple fracture mechanism. After HTMT, there is a slight decrease (relative to THT) in the steel impact strength in almost the entire temperature range under consideration and, accordingly, an increase in the temperature of its ductile-brittle transition. This is due to the tests’ geometry, in which the direction of impact occurs in the plane of the layered structure, and it facilitates the formation of delamination cracks.
- 2 January 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 66 (12) , 1235-1241
Microstructure, Mechanical Properties and Fracture of Austenitic Steel EK-164 After Warm Deformation at 600–900°C
- 2 January 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 66 (12) , 1235-1241
Microstructure, Mechanical Properties and Fracture of Austenitic Steel EK-164 After Warm Deformation at 600–900°C
- Open Access
- 29 December 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (6) , 725-732-732
Structural-phase transformations of 12% chromium ferritic-martensitic steel EP-823
The features of phase transformations of 12 % chromium ferritic-martensitic steel EP-823 under heating and cooling conditions in the temperature range from 30 to 1100 ℃ were studied by the methods of high-temperature X-ray diffraction analysis (XRD) in situ and differential scanning calorimetry (DSC). According to XRD in situ data, upon heating, the temperatures of the beginning and end of the (α → γ) transformation of ferrite (martensite – austenite) are Ac1 ≈ 880 °C, Ac3 ≈ 1000 °C, respectively. Upon cooling, a diffusion (γ → α) transformation occurs with critical points – Аr1 ≈ 860°С (beginning temperature) and Аr3 ≈ 840 °С (end temperature). According to DSC data, during heating, the critical points of the (α → γ) transformation are Ac1 ≈ 840 °C and Ac3 ≈ 900 °C. During cooling, a martensitic (γ → α) transformation is realized with critical points of the beginning of Ms = 344 ℃ and the end of Mf = 212 ℃ of this transformation. The XRD in situ analysis revealed no precipitation of carbide phases under heating and cooling conditions of steel EP-823. Position of the critical points of phase transformations depends on the research method (XRD in situ or DSC), which is determined by the difference in effective (taking into account the time for shooting in the XRD method) heating-cooling rate. The effect of elemental composition on the position of critical points of phase transformations and the formation of structural-phase states of ferritic-martensitic steels is discussed. It is shown that the increased content of ferrite-stabilizing elements (Cr, Mo, Nb) in composition of EP-823 steel, compared with other steels of the same class, expands the region of existence of the ferrite phase, which can contribute to an increase in the temperature of Ac1 .
- 29 December 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (6) , 725-732-732
Open AccessStructural-phase transformations of 12% chromium ferritic-martensitic steel EP-823
The features of phase transformations of 12 % chromium ferritic-martensitic steel EP-823 under heating and cooling conditions in the temperature range from 30 to 1100 ℃ were studied by the methods of high-temperature X-ray diffraction analysis (XRD) in situ and differential scanning calorimetry (DSC). According to XRD in situ data, upon heating, the temperatures of the beginning and end of the (α → γ) transformation of ferrite (martensite – austenite) are Ac1 ≈ 880 °C, Ac3 ≈ 1000 °C, respectively. Upon cooling, a diffusion (γ → α) transformation occurs with critical points – Аr1 ≈ 860°С (beginning temperature) and Аr3 ≈ 840 °С (end temperature). According to DSC data, during heating, the critical points of the (α → γ) transformation are Ac1 ≈ 840 °C and Ac3 ≈ 900 °C. During cooling, a martensitic (γ → α) transformation is realized with critical points of the beginning of Ms = 344 ℃ and the end of Mf = 212 ℃ of this transformation. The XRD in situ analysis revealed no precipitation of carbide phases under heating and cooling conditions of steel EP-823. Position of the critical points of phase transformations depends on the research method (XRD in situ or DSC), which is determined by the difference in effective (taking into account the time for shooting in the XRD method) heating-cooling rate. The effect of elemental composition on the position of critical points of phase transformations and the formation of structural-phase states of ferritic-martensitic steels is discussed. It is shown that the increased content of ferrite-stabilizing elements (Cr, Mo, Nb) in composition of EP-823 steel, compared with other steels of the same class, expands the region of existence of the ferrite phase, which can contribute to an increase in the temperature of Ac1 .
- Open Access
Microstructure Features and Mechanical Properties of Modified Low-Activation Austenitic Steel in the Temperature Range of 20 to 750 °C
A new low-activation austenitic steel with a modified composition and high austenite stability is proposed. The features of its microstructure after solution treatment (ST) and cold rolling (CR) are studied. The mechanical properties and features of the fracture behavior of this steel under tensile tests in the temperature range of 20–750 °C are discussed. After ST, an austenitic structure with stacking faults and dispersed carbide particles of the MC and M23C6 types is observed in the steel. After CR, the grains are refined, and the average grain size decreases from 41.4 µm (after ST) to 33.9 µm. High-density microtwin packets form in the material, and the dislocation density increases relative to that after ST. As the test temperature increases from 20 to 750 °C, the yield strength of the steel decreases by approximately two times, from ≈300 to 150 MPa (for ST) and from ≈700 to 370 MPa (for CR). In the studied temperature range, the steel demonstrates up to 2.6 times higher values of elongation to failure, ≈40–80% (for ST) and ≈13–27% (for CR), compared to steels of similar compositions and lower manganese content. Mechanical twinning contributes to the high steel ductility up to 300 °C. Signs of discontinuous flow in the tensile curves after ST in the temperature range of 500–600 °C and a decrease in the elongation to failure in the close temperature range indicate dynamic strain aging (DSA). Steel fracture after tension at all test temperatures mainly occurs via a ductile dimple transcrystalline mechanism with elements of ductile intercrystalline fracture. It is shown that cracks nucleate on clusters of dispersed second-phase particles. The mechanisms of plastic deformation, fracture, and strengthening of the proposed modified low-activation austenitic steel are discussed.
Open AccessMicrostructure Features and Mechanical Properties of Modified Low-Activation Austenitic Steel in the Temperature Range of 20 to 750 °C
A new low-activation austenitic steel with a modified composition and high austenite stability is proposed. The features of its microstructure after solution treatment (ST) and cold rolling (CR) are studied. The mechanical properties and features of the fracture behavior of this steel under tensile tests in the temperature range of 20–750 °C are discussed. After ST, an austenitic structure with stacking faults and dispersed carbide particles of the MC and M23C6 types is observed in the steel. After CR, the grains are refined, and the average grain size decreases from 41.4 µm (after ST) to 33.9 µm. High-density microtwin packets form in the material, and the dislocation density increases relative to that after ST. As the test temperature increases from 20 to 750 °C, the yield strength of the steel decreases by approximately two times, from ≈300 to 150 MPa (for ST) and from ≈700 to 370 MPa (for CR). In the studied temperature range, the steel demonstrates up to 2.6 times higher values of elongation to failure, ≈40–80% (for ST) and ≈13–27% (for CR), compared to steels of similar compositions and lower manganese content. Mechanical twinning contributes to the high steel ductility up to 300 °C. Signs of discontinuous flow in the tensile curves after ST in the temperature range of 500–600 °C and a decrease in the elongation to failure in the close temperature range indicate dynamic strain aging (DSA). Steel fracture after tension at all test temperatures mainly occurs via a ductile dimple transcrystalline mechanism with elements of ductile intercrystalline fracture. It is shown that cracks nucleate on clusters of dispersed second-phase particles. The mechanisms of plastic deformation, fracture, and strengthening of the proposed modified low-activation austenitic steel are discussed.