Zhiyi Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhiyi Jin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Zhenqiang Yao
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
4 shared publications - Xifang Zhang
College of Smart Energy, Shanghai Jiao Tong University, Shanghai 200240, China
3 shared publications - Zhibao Hou
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
2 shared publications - Bei Peng
Wuhan Second Ship Design and Research Institute
1 shared publication - Haifeng Du
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
1 shared publication - Hong Shen
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
1 shared publication
Latest Publications
- Open Access
Wettability and Frictional Studies of PEEK Composites against Co-Cr Alloys with Surface Textures
With the aim of promoting the qualities for total hip joint replacement, the wettability and tribological behaviors of PEEK composites pins with two sets of different fillers (PEEK/CF or PEEK/CF/PTFE/graphite) against Co-Cr alloy discs with five categories of surface textures (polished, orthogonal, spiral, r-θ, and orthogonal combined with spiral) were explored. It is revealed that the existence of CF in PEEK matrix increases the hydrophilicity in addition to the strength of PEEK, while the addition of PTFE increases the hydrophobicity of PEEK. The Co-Cr alloy discs with hydrophilic properties can be adjusted as hydrophobic, with the depth of textured grooves exceeding the critical sag height determined by the contact angle and the groove width. It can be concluded that PEEK/CF/PTFE/graphite composite has a lower wear rate than PEEK only reinforced with CF against Co-Cr alloy, both without surface texture and with shallow or deep grooves. The existence of shallow grooves on the disc surface could help the PEEK blends to achieve a steady friction against Co-Cr alloy in addition to collecting the worn debris. PEEK blend pins with 10 vol% CF, 10 vol% PTFE and 10 vol% graphite can achieve a lower friction coefficient of no more than 0.2 against Co-Cr alloy discs with shallow grooves around 3.5 μm in orthogonal or spiral textures.
Open AccessWettability and Frictional Studies of PEEK Composites against Co-Cr Alloys with Surface Textures
With the aim of promoting the qualities for total hip joint replacement, the wettability and tribological behaviors of PEEK composites pins with two sets of different fillers (PEEK/CF or PEEK/CF/PTFE/graphite) against Co-Cr alloy discs with five categories of surface textures (polished, orthogonal, spiral, r-θ, and orthogonal combined with spiral) were explored. It is revealed that the existence of CF in PEEK matrix increases the hydrophilicity in addition to the strength of PEEK, while the addition of PTFE increases the hydrophobicity of PEEK. The Co-Cr alloy discs with hydrophilic properties can be adjusted as hydrophobic, with the depth of textured grooves exceeding the critical sag height determined by the contact angle and the groove width. It can be concluded that PEEK/CF/PTFE/graphite composite has a lower wear rate than PEEK only reinforced with CF against Co-Cr alloy, both without surface texture and with shallow or deep grooves. The existence of shallow grooves on the disc surface could help the PEEK blends to achieve a steady friction against Co-Cr alloy in addition to collecting the worn debris. PEEK blend pins with 10 vol% CF, 10 vol% PTFE and 10 vol% graphite can achieve a lower friction coefficient of no more than 0.2 against Co-Cr alloy discs with shallow grooves around 3.5 μm in orthogonal or spiral textures.
- 2 August 2023
- Published by Springer Nature
- p. 160-178
The Axial Heat Transfer Behavior Based Upon Taylor Vortex in Annular Fluid Flow with Rotating Inner Cylinder
- 2 August 2023
- Published by Springer Nature
- p. 160-178
The Axial Heat Transfer Behavior Based Upon Taylor Vortex in Annular Fluid Flow with Rotating Inner Cylinder
- Open Access
Material Removal Capability and Profile Quality Assessment on Silicon Carbide Micropillar Fabrication with a Femtosecond Laser
Silicon carbide (SiC) has a variety of applications because of its favorable chemical stability and outstanding physical characteristics, such as high hardness and high rigidity. In this study, a femtosecond laser with a spiral scanning radial offset of 5 μm and a spot radius of 6 μm is utilized to process micropillars on a SiC plate. The influence of pulsed laser beam energies and laser translation velocities on the micropillar profiles, dimensions, surface roughness Ra, and material removal capability (MRC) of micropillars was investigated. The processing results indicate that the micropillar has the best perpendicularity, with a micropillar bottom angle of 75.59° under a pulsed beam energy of 50 μJ in the range of 10–70 μJ, with a pulsed repetition rate of 600 kHz and a translation velocity of 0.1 m/s. As the laser translation velocity increases between 0.2 m/s and 1.0 m/s under a fixed pulsed beam energy of 50 μJ and a constant pulsed repetition rate of 600 kHz, the micropillar height decreases from 119.88 μm to 81.79 μm, with the MRC value increasing from 1.998 μm3/μJ to 6.816 μm3/μJ, while the micropillar bottom angle increases from 68.87° to 75.59°, and the Ra value diminishes from 0.836 μm to 0.341 μm. It is suggested that a combination of a higher pulsed laser beam energy with a faster laser translation speed is recommended to achieve micropillars with the same height, as well as an improved processing efficiency and surface finish.
Open AccessMaterial Removal Capability and Profile Quality Assessment on Silicon Carbide Micropillar Fabrication with a Femtosecond Laser
Silicon carbide (SiC) has a variety of applications because of its favorable chemical stability and outstanding physical characteristics, such as high hardness and high rigidity. In this study, a femtosecond laser with a spiral scanning radial offset of 5 μm and a spot radius of 6 μm is utilized to process micropillars on a SiC plate. The influence of pulsed laser beam energies and laser translation velocities on the micropillar profiles, dimensions, surface roughness Ra, and material removal capability (MRC) of micropillars was investigated. The processing results indicate that the micropillar has the best perpendicularity, with a micropillar bottom angle of 75.59° under a pulsed beam energy of 50 μJ in the range of 10–70 μJ, with a pulsed repetition rate of 600 kHz and a translation velocity of 0.1 m/s. As the laser translation velocity increases between 0.2 m/s and 1.0 m/s under a fixed pulsed beam energy of 50 μJ and a constant pulsed repetition rate of 600 kHz, the micropillar height decreases from 119.88 μm to 81.79 μm, with the MRC value increasing from 1.998 μm3/μJ to 6.816 μm3/μJ, while the micropillar bottom angle increases from 68.87° to 75.59°, and the Ra value diminishes from 0.836 μm to 0.341 μm. It is suggested that a combination of a higher pulsed laser beam energy with a faster laser translation speed is recommended to achieve micropillars with the same height, as well as an improved processing efficiency and surface finish.
- Open Access
Tribological Properties of Carbon Fiber-Reinforced PEEK against 304 Stainless Steel with Reticulate Surface Texture
With the aim of improving the durability and reliability of polyetheretherketone (PEEK) composites reinforced with carbon fiber (CF) as thrust bearings without lubricants, a reticulate surface texture was fabricated by plane honing on a stainless steel (SS) counterpart to promote its tribological properties. Pin-on-disk experiments were designed, with the results showing that the reticulate surface texture effectively reduces the friction coefficient from 0.40 to 0.20 compared with the polished SS surface, within the range of the pv value from 0.185 to 1.85 MPa∙m/s. The wear mechanism of the polished SS surface against CF-PEEK, proven with SEM and EDS observations as well as AE measurements, is revealed, falling into abrasive wear with SS particles embedded in the friction interface around the CF strips, causing three-body contact. The reduction in the friction coefficient of the textured SS disk against the CF-PEEK pin can be achieved due to diminution of the CF wear debris and SS particles, which are scraped off by the groove edges and trapped by the groove valleys, reducing the three-body abrasive wear, while the honed plateau is used as a flank surface like a cutting tool to scratch more soft PEEK particles as the transferred film, owing to adhesive wear. This investigation suggests that the SS disk with a honed surface structure can be used as the counterpart of CF-PEEK bearings with a low friction coefficient and wear rate under dry friction.
Open AccessTribological Properties of Carbon Fiber-Reinforced PEEK against 304 Stainless Steel with Reticulate Surface Texture
With the aim of improving the durability and reliability of polyetheretherketone (PEEK) composites reinforced with carbon fiber (CF) as thrust bearings without lubricants, a reticulate surface texture was fabricated by plane honing on a stainless steel (SS) counterpart to promote its tribological properties. Pin-on-disk experiments were designed, with the results showing that the reticulate surface texture effectively reduces the friction coefficient from 0.40 to 0.20 compared with the polished SS surface, within the range of the pv value from 0.185 to 1.85 MPa∙m/s. The wear mechanism of the polished SS surface against CF-PEEK, proven with SEM and EDS observations as well as AE measurements, is revealed, falling into abrasive wear with SS particles embedded in the friction interface around the CF strips, causing three-body contact. The reduction in the friction coefficient of the textured SS disk against the CF-PEEK pin can be achieved due to diminution of the CF wear debris and SS particles, which are scraped off by the groove edges and trapped by the groove valleys, reducing the three-body abrasive wear, while the honed plateau is used as a flank surface like a cutting tool to scratch more soft PEEK particles as the transferred film, owing to adhesive wear. This investigation suggests that the SS disk with a honed surface structure can be used as the counterpart of CF-PEEK bearings with a low friction coefficient and wear rate under dry friction.