Mariel Amparo Fernandez Aramayo
Mariel Amparo Fernandez Aramayo has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Idalina Vieira Aoki
Polytechnic School, Universidade de São Paulo, Sao Paulo 05508-220, Sao Paulo, Brazil
3 shared publications - Brunela Pereira da Silva
Department of Engineering and Computing, State University of Santa Cruz
1 shared publication - Bruno B. Storte
Mackenzie Institute for Research in Graphene and Nanotechnologies – MackGraphe São Paulo Brazil
1 shared publication - Bélgica Andrade
Hospital Clínico San Borja Arriarán-Chile, Santiago 8360160, Chile
1 shared publication - Camila Marchetti Maroneze
Universidade Presbiteriana Mackenzie/ Instituto Mackenzie de Pesquisa em Grafeno e Nanotecnologias- Mackgraphe
1 shared publication - Camila Quartim de Moraes Bruna
Universidade de São Paulo, Brazil; Universidade de São Paulo, Brazil
1 shared publication
Latest Publications
- Open Access
- 4 October 2026
- Published by Wiley in Polymer Composites
Functionalized Graphene‐Reinforced Thermoplastic Polyurethane Nanocomposites: Thermomechanical and Magnetic Properties
Polymeric nanocomposites have attracted significant interest for their low density, processability, and multifunctional properties, making them suitable for applications such as flexible electronics, sensors, biomedical devices, and functional coatings. In this work, thermoplastic polyurethane (TPU) nanocomposites reinforced with thermally reduced graphene oxide (TrGO) functionalized with nickel (Ni) and cobalt (Co) nanoparticles were developed via melt blending in a twin‐screw extruder and systematically characterized. Structural analyses using Raman spectroscopy, X‐ray diffraction (XRD), and scanning electron microscopy (SEM) confirmed successful TrGO functionalization and the formation of ordered lamellar structures. Thermogravimetric analysis (TGA) indicated that incorporating the nanofillers did not significantly affect the thermal stability or phase‐transition behavior of TPU. Dynamic mechanical analysis (DMA) revealed increased stiffness below the glass transition temperature, demonstrating effective reinforcement of the polymer matrix. Tensile testing showed substantial improvements in mechanical performance, with increases of up to 145% in tensile strength and 146% in elongation at break compared with neat TPU. Rheological measurements indicated higher viscosity and enhanced pseudoplastic behavior, suggesting strong polymer‐filler interactions. Magnetic characterization revealed weak ferromagnetic contributions in the Ni‐ and Co‐functionalized systems. These results demonstrate that metal‐functionalized TrGO is an effective multifunctional filler for TPU, providing significant mechanical reinforcement while maintaining thermal stability, with potential applications in flexible electronics, smart coatings, and advanced polymeric devices.
- 4 October 2026
- Published by Wiley in Polymer Composites
Open AccessFunctionalized Graphene‐Reinforced Thermoplastic Polyurethane Nanocomposites: Thermomechanical and Magnetic Properties
Polymeric nanocomposites have attracted significant interest for their low density, processability, and multifunctional properties, making them suitable for applications such as flexible electronics, sensors, biomedical devices, and functional coatings. In this work, thermoplastic polyurethane (TPU) nanocomposites reinforced with thermally reduced graphene oxide (TrGO) functionalized with nickel (Ni) and cobalt (Co) nanoparticles were developed via melt blending in a twin‐screw extruder and systematically characterized. Structural analyses using Raman spectroscopy, X‐ray diffraction (XRD), and scanning electron microscopy (SEM) confirmed successful TrGO functionalization and the formation of ordered lamellar structures. Thermogravimetric analysis (TGA) indicated that incorporating the nanofillers did not significantly affect the thermal stability or phase‐transition behavior of TPU. Dynamic mechanical analysis (DMA) revealed increased stiffness below the glass transition temperature, demonstrating effective reinforcement of the polymer matrix. Tensile testing showed substantial improvements in mechanical performance, with increases of up to 145% in tensile strength and 146% in elongation at break compared with neat TPU. Rheological measurements indicated higher viscosity and enhanced pseudoplastic behavior, suggesting strong polymer‐filler interactions. Magnetic characterization revealed weak ferromagnetic contributions in the Ni‐ and Co‐functionalized systems. These results demonstrate that metal‐functionalized TrGO is an effective multifunctional filler for TPU, providing significant mechanical reinforcement while maintaining thermal stability, with potential applications in flexible electronics, smart coatings, and advanced polymeric devices.
- 27 February 2025
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 32 (5) , 1186-1198
Self-healing capability of epoxy coating using dual-component microcapsules under immersion
- 27 February 2025
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 32 (5) , 1186-1198
Self-healing capability of epoxy coating using dual-component microcapsules under immersion
- Open Access
Eco-Friendly Waterborne Polyurethane Coating Modified with Ethylenediamine-Functionalized Graphene Oxide for Enhanced Anticorrosion Performance
This study explores the potential of graphene oxide (GO) as an additive in waterborne polyurethane (WPU) resins to create eco-friendly coatings with enhanced anticorrosive properties. Traditionally, WPU’s hydrophilic nature has limited its use in corrosion-resistant coatings. We investigate the impact of incorporating various GO concentrations (0.01, 0.1, and 1.3 wt%) and functionalizing GO with ethylenediamine (EDA) on the development of anticorrosive coatings for carbon steel. It was observed, by potentiodynamic polarization analysis in a 3.5% NaCl solution, that the low GO content in the WPU matrix significantly improved anticorrosion properties, with the 0.01 wt% GO-EDA formulation showing exceptional performance, high Ecorr (−117.82 mV), low icorr (3.70 × 10−9 A cm−2), and an inhibition corrosion efficiency (η) of 99.60%. Raman imaging mappings revealed that excessive GO content led to agglomeration, creating pathways for corrosive species. In UV/condensation tests, the 0.01 wt% GO-EDA coating exhibited the most promising results, with minimal corrosion products compared to pristine WPU. The large lateral dimensions of GO sheets and the cross-linking facilitated by EDA enhanced the interfacial properties and dispersion within the WPU matrix, resulting in superior barrier properties and anticorrosion performance. This advancement underscores the potential of GO-based coatings for environmentally friendly corrosion protection.
Open AccessEco-Friendly Waterborne Polyurethane Coating Modified with Ethylenediamine-Functionalized Graphene Oxide for Enhanced Anticorrosion Performance
This study explores the potential of graphene oxide (GO) as an additive in waterborne polyurethane (WPU) resins to create eco-friendly coatings with enhanced anticorrosive properties. Traditionally, WPU’s hydrophilic nature has limited its use in corrosion-resistant coatings. We investigate the impact of incorporating various GO concentrations (0.01, 0.1, and 1.3 wt%) and functionalizing GO with ethylenediamine (EDA) on the development of anticorrosive coatings for carbon steel. It was observed, by potentiodynamic polarization analysis in a 3.5% NaCl solution, that the low GO content in the WPU matrix significantly improved anticorrosion properties, with the 0.01 wt% GO-EDA formulation showing exceptional performance, high Ecorr (−117.82 mV), low icorr (3.70 × 10−9 A cm−2), and an inhibition corrosion efficiency (η) of 99.60%. Raman imaging mappings revealed that excessive GO content led to agglomeration, creating pathways for corrosive species. In UV/condensation tests, the 0.01 wt% GO-EDA coating exhibited the most promising results, with minimal corrosion products compared to pristine WPU. The large lateral dimensions of GO sheets and the cross-linking facilitated by EDA enhanced the interfacial properties and dispersion within the WPU matrix, resulting in superior barrier properties and anticorrosion performance. This advancement underscores the potential of GO-based coatings for environmentally friendly corrosion protection.
- 28 February 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (19)
Synthesis of innovative epoxy resin and polyamine hardener microcapsules and their age monitoring by confocal Raman imaging
We present an innovative breakthrough encompassing synthesis, characterization, and age monitoring of epoxy resin and polyamine hardener microcapsules to form a dual‐component system for self‐healing anticorrosion coatings. The epoxy resin microcapsules (ER‐MC) are fabricated through oil–water emulsion and in situ polymerization, with poly (urea‐formaldehyde‐melamine) as shell material and a mixture of epoxy resin and n‐butyl glycidyl ether as core material. Modified aliphatic fast reactive polyamine hardener is microencapsulated with polymethylmethacrylate as shell using double emulsion and solvent evaporation method (PAH‐MC). Characterization includes optical microscopy, scanning electron microscopy, and particle size analyzer utilizing laser diffraction. The resulting microcapsules exhibited spherical shape with smooth surface devoid of porosity. Fourier transform infrared spectroscopy‐attenuated total reflection is utilized to confirm encapsulation by identifying the chemical structures of both microcapsule constituents. The thermogravimetric analysis further confirms the core content of microcapsules obtained from solvent extraction. ER‐MC contains approximately 66 wt %, while PAH‐MC stands 40 wt %, both showcasing remarkable thermal stability below 200°C. A ten‐month storage period fails to diminish the presence of the healing agents encapsulated within the polymeric walls, which is revealed by Raman spectroscopy utilizing 2D compositional mapping. This research demonstrates the viability of creating dual microcapsules and exemplify their potential for developing self‐healing coatings with dual‐component film‐forming healing agents.
- 28 February 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (19)
Synthesis of innovative epoxy resin and polyamine hardener microcapsules and their age monitoring by confocal Raman imaging
We present an innovative breakthrough encompassing synthesis, characterization, and age monitoring of epoxy resin and polyamine hardener microcapsules to form a dual‐component system for self‐healing anticorrosion coatings. The epoxy resin microcapsules (ER‐MC) are fabricated through oil–water emulsion and in situ polymerization, with poly (urea‐formaldehyde‐melamine) as shell material and a mixture of epoxy resin and n‐butyl glycidyl ether as core material. Modified aliphatic fast reactive polyamine hardener is microencapsulated with polymethylmethacrylate as shell using double emulsion and solvent evaporation method (PAH‐MC). Characterization includes optical microscopy, scanning electron microscopy, and particle size analyzer utilizing laser diffraction. The resulting microcapsules exhibited spherical shape with smooth surface devoid of porosity. Fourier transform infrared spectroscopy‐attenuated total reflection is utilized to confirm encapsulation by identifying the chemical structures of both microcapsule constituents. The thermogravimetric analysis further confirms the core content of microcapsules obtained from solvent extraction. ER‐MC contains approximately 66 wt %, while PAH‐MC stands 40 wt %, both showcasing remarkable thermal stability below 200°C. A ten‐month storage period fails to diminish the presence of the healing agents encapsulated within the polymeric walls, which is revealed by Raman spectroscopy utilizing 2D compositional mapping. This research demonstrates the viability of creating dual microcapsules and exemplify their potential for developing self‐healing coatings with dual‐component film‐forming healing agents.
- Open Access
Evaluation of the Presence of Biofilms in Corrosive Points in Surgical Instruments after Reprocessing
Corrosive surgical instruments are routinely observed in central sterile services departments around the world. In addition to other risks, they can harbor microorganisms in the form of biofilms. Thus, this study aimed to evaluate whether biofilms intentionally formed at corrosion points on surgical instruments are removable by manual and automated cleaning followed by sterilization. Laboratory experiments were performed where samples of corroded surgical instruments in use in practice were evaluated for biofilm presence using a scanning electron microscope. No biofilms were observed in the samples subjected to manual and automated cleaning, nor in the samples in which there was no intentional biofilm formation. Residual organic matter without the presence of microorganisms was observed.
Open AccessEvaluation of the Presence of Biofilms in Corrosive Points in Surgical Instruments after Reprocessing
Corrosive surgical instruments are routinely observed in central sterile services departments around the world. In addition to other risks, they can harbor microorganisms in the form of biofilms. Thus, this study aimed to evaluate whether biofilms intentionally formed at corrosion points on surgical instruments are removable by manual and automated cleaning followed by sterilization. Laboratory experiments were performed where samples of corroded surgical instruments in use in practice were evaluated for biofilm presence using a scanning electron microscope. No biofilms were observed in the samples subjected to manual and automated cleaning, nor in the samples in which there was no intentional biofilm formation. Residual organic matter without the presence of microorganisms was observed.