Marius Ellingsen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marius Ellingsen has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Alevtina Smirnova
South Dakota School of Mines and Technology
2 shared publications - Abiral Baniya
Mechanical and Aerospace Engineering Syracuse University Syracuse NY 13244 USA
1 shared publication - Abu Md. Numan-Al-Mobin
South Dakota School of Mines and Technology, USA
1 shared publication Ali Mohammed Jobayer
Electrical Engineering, South Dakota School of Mines and Engineering, Rapid City, SD, United States
1 shared publicationAndrew J. Snyder
1 shared publicationArmand Lannerd
Department of Chemistry, Biology, and Health Sciences, South Dakota School of Mines & Technology, Rapid City, SD, United States
1 shared publication
Latest Publications
- 30 October 2025
- Published by Springer Nature in JOM
- Vol. 78 (2) , 1354-1367
Microstructure and Corrosion Properties of NASA HR-1 Cold-Sprayed Coatings
- 30 October 2025
- Published by Springer Nature in JOM
- Vol. 78 (2) , 1354-1367
Microstructure and Corrosion Properties of NASA HR-1 Cold-Sprayed Coatings
- 19 January 2023
- Published by Elsevier
- p. 295-317
Application of supersonic cold spray for solid-state battery manufacturing
- 19 January 2023
- Published by Elsevier
- p. 295-317
Application of supersonic cold spray for solid-state battery manufacturing
- Open Access
- 9 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (2)
Supersonic cold-sprayed Si composite alloy as anode for Li-ion batteries
The increasing demand for lithium-ion batteries (LIBs) continuously stimulates the research community to seek advanced fabrication of anodes with improved performance and lifespan. Silicon (Si), as one of the most promising anode materials, has been the main focus of both research and industry. In this paper, we report a type of Si alloy anode for LIBs manufactured by the supersonic cold spray technique. The microscopic analysis revealed the uniform morphologies of the anodes, indicating that Si and other metal particles were well bonded. Specific discharge capacities were obtained for the cold-sprayed anodes by half-coin cell tests, with the highest value of 1047 mAh g−1 at a current rate of 0.05 C. Most importantly, the energy-dispersive x-ray spectroscopy results demonstrated none oxidation of the powders after the cold spray process. The results strongly indicate that the concept of using cold spray technique to fabricate Si alloy anode is feasible. Compared to the conventional methods of fabricating Si anodes, the cold spray approach is simple, convenient, and scalable. This method may revolutionarily change the LIBs industries.
- 9 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (2)
Open AccessSupersonic cold-sprayed Si composite alloy as anode for Li-ion batteries
The increasing demand for lithium-ion batteries (LIBs) continuously stimulates the research community to seek advanced fabrication of anodes with improved performance and lifespan. Silicon (Si), as one of the most promising anode materials, has been the main focus of both research and industry. In this paper, we report a type of Si alloy anode for LIBs manufactured by the supersonic cold spray technique. The microscopic analysis revealed the uniform morphologies of the anodes, indicating that Si and other metal particles were well bonded. Specific discharge capacities were obtained for the cold-sprayed anodes by half-coin cell tests, with the highest value of 1047 mAh g−1 at a current rate of 0.05 C. Most importantly, the energy-dispersive x-ray spectroscopy results demonstrated none oxidation of the powders after the cold spray process. The results strongly indicate that the concept of using cold spray technique to fabricate Si alloy anode is feasible. Compared to the conventional methods of fabricating Si anodes, the cold spray approach is simple, convenient, and scalable. This method may revolutionarily change the LIBs industries.
- Open Access
- 8 December 2022
- Published by Elsevier in Additive Manufacturing
- Vol. 61
Microstructure and mechanical properties of cold spray additive manufactured Cu-Cr-Nb and Fe-Ni-Cr alloys
- 8 December 2022
- Published by Elsevier in Additive Manufacturing
- Vol. 61
Open AccessMicrostructure and mechanical properties of cold spray additive manufactured Cu-Cr-Nb and Fe-Ni-Cr alloys