Yanjun Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yanjun Shi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Hui Li
Florida State University,Center for Advanced Power Systems,Tallahassee,FL
16 shared publicationsRen Xie
Center for Advanced Power Systems, Florida State University, Tallahassee, FL, USA
11 shared publicationsLu Wang
Infineon Technologies Americas Corp, El Segundo, CA, USA
9 shared publications- Hui Li
Department of Electrical and Computer Engineering, Florida State University, Tallahassee, FL, USA
7 shared publications Yuxiang Shi
ABB Corporate Research Center, Raleigh, NC, USA
6 shared publications- Lu Wang
Center for Advanced Power Systems, Florida State University, 7823 Tallahassee, Florida United States
4 shared publications
Latest Publications
- 30 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 7894-7906
Analysis, Modeling, and Experiments of a Nonlinear Inductor-Based Fault Current Commutation Strategy for a Hybrid DC Circuit Breaker
Medium voltage dc (MVdc) power system offers a potent solution for the high power density, agility, and robustness required by electric ships with escalating power needs. However, the dc power systems suffer from short-circuit fault managing issues. To solve the issue, a hybrid dc circuit breaker has been developed, featuring a novel piezoelectric actuated fast mechanical switch (FMS) and a sequential metal-oxide varistor insertion scheme. A key innovation is its nonlinear inductor-based fault current commutation strategy, designed for fast fault current extinguishment and ensuring arc-less operation of the FMS. By utilizing the saturation phenomenon properly, the inductor with variable inductance can hold current around zero to enable arc-less open of the FMS without slowing down the fault current commutation speed. The paper analyzes the features of the nonlinear inductor, presents a fractal RL circuit to model the frequency-related inductance variance and the saturation phenomenon in the time domain. Based on the model of the circuit breaker, including the nonlinear inductor, a genetic algorithm based multi-objective optimization method is developed to design the fault current commutation circuit. Experimental results with 4 kV dc voltage are presented to confirm the accuracy of the model of the nonlinear inductor and the optimized design method.
- 30 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 7894-7906
Analysis, Modeling, and Experiments of a Nonlinear Inductor-Based Fault Current Commutation Strategy for a Hybrid DC Circuit Breaker
Medium voltage dc (MVdc) power system offers a potent solution for the high power density, agility, and robustness required by electric ships with escalating power needs. However, the dc power systems suffer from short-circuit fault managing issues. To solve the issue, a hybrid dc circuit breaker has been developed, featuring a novel piezoelectric actuated fast mechanical switch (FMS) and a sequential metal-oxide varistor insertion scheme. A key innovation is its nonlinear inductor-based fault current commutation strategy, designed for fast fault current extinguishment and ensuring arc-less operation of the FMS. By utilizing the saturation phenomenon properly, the inductor with variable inductance can hold current around zero to enable arc-less open of the FMS without slowing down the fault current commutation speed. The paper analyzes the features of the nonlinear inductor, presents a fractal RL circuit to model the frequency-related inductance variance and the saturation phenomenon in the time domain. Based on the model of the circuit breaker, including the nonlinear inductor, a genetic algorithm based multi-objective optimization method is developed to design the fault current commutation circuit. Experimental results with 4 kV dc voltage are presented to confirm the accuracy of the model of the nonlinear inductor and the optimized design method.
- Top Cited Papers
- 28 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8851-8865
Control Development and Fault Current Commutation Test for the EDISON Hybrid Circuit Breaker
The dc circuit breaker is an indispensable building block for dc network systems. Hybrid circuit breakers that combine mechanical and solid-state switches have more potential to be utilized in dc distribution networks because of their lower conduction losses and fast interrupt speed. The efficient energy dc interrupter with surge protection (EDISON) removes any solid-state circuit in the main current path, thereby substantially reducing the conduction losses during normal operations. However, it requires a dedicated control with fast dynamics because any false triggering of the mechanical switch or solid-state switches of the breaker would lead to a commutation failure and a potential unquenchable arc. This article proposes an FSM-based control scheme that guarantees the accurate and fast control response during a fault event. Due to this fast response requirement, a dual-core-CPU-based control architecture is applied featuring parallel taskings and negligible communication delays between the two cores. Furthermore, a control-law accelerator is employed to further reduce the latency of the program execution by 33%. The controller hardware-in-the-loop (CHIL) model of the EDISON breaker is implemented in OPAL-RT to verify the control scheme and derisk the prototype test. A fifth-order RLC network is developed to characterize the mechanical switch behavior such that the hybrid circuit model can be simulated in the CHIL solely by circuit components. Finally, the proposed control scheme is implemented and validated in a prototype test with a 3 kA interrupting current and a 60 A/ ${\mu }$ s current commutation rate.
- 28 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8851-8865
Top Cited PapersControl Development and Fault Current Commutation Test for the EDISON Hybrid Circuit Breaker
The dc circuit breaker is an indispensable building block for dc network systems. Hybrid circuit breakers that combine mechanical and solid-state switches have more potential to be utilized in dc distribution networks because of their lower conduction losses and fast interrupt speed. The efficient energy dc interrupter with surge protection (EDISON) removes any solid-state circuit in the main current path, thereby substantially reducing the conduction losses during normal operations. However, it requires a dedicated control with fast dynamics because any false triggering of the mechanical switch or solid-state switches of the breaker would lead to a commutation failure and a potential unquenchable arc. This article proposes an FSM-based control scheme that guarantees the accurate and fast control response during a fault event. Due to this fast response requirement, a dual-core-CPU-based control architecture is applied featuring parallel taskings and negligible communication delays between the two cores. Furthermore, a control-law accelerator is employed to further reduce the latency of the program execution by 33%. The controller hardware-in-the-loop (CHIL) model of the EDISON breaker is implemented in OPAL-RT to verify the control scheme and derisk the prototype test. A fifth-order RLC network is developed to characterize the mechanical switch behavior such that the hybrid circuit model can be simulated in the CHIL solely by circuit components. Finally, the proposed control scheme is implemented and validated in a prototype test with a 3 kA interrupting current and a 60 A/ ${\mu }$ s current commutation rate.
- Open Access
- 2 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 149-160
Modular Multilevel Converter Switching Frequency Harmonics Analysis and Suppression Through Cell Voltage Control
This paper investigates the impact of reference bias on the high-frequency voltage spectrum for the modular multilevel converters (MMC). Analytical solution of the voltage spectrum under carrier Phase Shifted Pulse Width Modulation (PSPWM) is derived using double Fourier integral analysis. The distribution of the switching frequency voltage harmonics is found to be directly related to the ratio between the dc-link voltage and the cell voltage. A control method utilizing this phenomenon is thereby proposed to suppress switching frequency harmonics in the Differential Mode Voltage (DMV) and Common Mode Voltage (CMV). Cell voltage control trade-offs considering different cell numbers, different ac voltages, $3^{rd}$ harmonics injection, and cell voltage stress are also investigated. The analysis and control method are validated through experiments on a 1.25 megawatt MMC testbed.- 2 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 149-160
Open AccessModular Multilevel Converter Switching Frequency Harmonics Analysis and Suppression Through Cell Voltage Control
This paper investigates the impact of reference bias on the high-frequency voltage spectrum for the modular multilevel converters (MMC). Analytical solution of the voltage spectrum under carrier Phase Shifted Pulse Width Modulation (PSPWM) is derived using double Fourier integral analysis. The distribution of the switching frequency voltage harmonics is found to be directly related to the ratio between the dc-link voltage and the cell voltage. A control method utilizing this phenomenon is thereby proposed to suppress switching frequency harmonics in the Differential Mode Voltage (DMV) and Common Mode Voltage (CMV). Cell voltage control trade-offs considering different cell numbers, different ac voltages, $3^{rd}$ harmonics injection, and cell voltage stress are also investigated. The analysis and control method are validated through experiments on a 1.25 megawatt MMC testbed. - Open Access
- 10 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 51-63
Intercell Transformer (ICT) Design Optimization and Interphase Crosstalk Mitigation of a 100-kW SiC Filter-Less Grid-Connected PV String Inverter
- 10 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 51-63
Open AccessIntercell Transformer (ICT) Design Optimization and Interphase Crosstalk Mitigation of a 100-kW SiC Filter-Less Grid-Connected PV String Inverter
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6419-6423
High Frequency Transformer Core Loss Analysis in Isolated Modular Multilevel DC-DC Converter for MVDC Application
An Isolated Modular Multilevel DC-DC Converter (iM2DC) operating with Phase Shifted - Square Wave Modulation (PS-SWM) featuring reduced passive components and low Total Device Rating (TDR) for MVDC applications is presented here, and the effect of the PS-SWM modulation scheme on high frequency (HF) transformer core loss is analyzed. A down-scaled iM2DC prototype is built with a 1:1 transformer and it is proved that the transformer losses are not affected by the staircase shaped voltage of the PS-SWM modulation. The transformer core loss is analytically found equal to the core loss obtained with pure square wave voltage excitation with 50% duty ratio. This simplifies the HF transformer design and optimization process for this application. The core loss is experimentally measured and validated.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6419-6423
High Frequency Transformer Core Loss Analysis in Isolated Modular Multilevel DC-DC Converter for MVDC Application
An Isolated Modular Multilevel DC-DC Converter (iM2DC) operating with Phase Shifted - Square Wave Modulation (PS-SWM) featuring reduced passive components and low Total Device Rating (TDR) for MVDC applications is presented here, and the effect of the PS-SWM modulation scheme on high frequency (HF) transformer core loss is analyzed. A down-scaled iM2DC prototype is built with a 1:1 transformer and it is proved that the transformer losses are not affected by the staircase shaped voltage of the PS-SWM modulation. The transformer core loss is analytically found equal to the core loss obtained with pure square wave voltage excitation with 50% duty ratio. This simplifies the HF transformer design and optimization process for this application. The core loss is experimentally measured and validated.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 577-582
Averaged and Small-Signal Models for Modular Multilevel Converter with Square-wave Modulation
In this paper, an averaged model and a small-signal model of a DC-DC converter built with back-to-back modular multilevel converters (MMC) operating with a square-wave modulation with low total device rating and passive component size are derived for a breakerless MVDC system application. The simulation verifications show the validity of the developed models.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 577-582
Averaged and Small-Signal Models for Modular Multilevel Converter with Square-wave Modulation
In this paper, an averaged model and a small-signal model of a DC-DC converter built with back-to-back modular multilevel converters (MMC) operating with a square-wave modulation with low total device rating and passive component size are derived for a breakerless MVDC system application. The simulation verifications show the validity of the developed models.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 499-504
High Frequency Transformer Design for Medium Voltage Shipboard DC-DC Converter
This paper presents an optimized high-frequency transformer design for a 6 kV, 100 kW Isolated Modular Multilevel DC-DC (iM2DC) converter for shipboard application with 50 kHz transformer ac frequency. The Phase Shifted Square Wave Modulation (PS-SWM) scheme produces an unconventional, non-sinusoidal ac voltage waveform that makes the high-frequency transformer design challenging. This paper proposes an optimized transformer design method by accurately estimating the transformer’s power loss for iM2DC converter while still utilizing the advantages associated with PS-SWM modulation. The findings are later validated by a down scaled prototype.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 499-504
High Frequency Transformer Design for Medium Voltage Shipboard DC-DC Converter
This paper presents an optimized high-frequency transformer design for a 6 kV, 100 kW Isolated Modular Multilevel DC-DC (iM2DC) converter for shipboard application with 50 kHz transformer ac frequency. The Phase Shifted Square Wave Modulation (PS-SWM) scheme produces an unconventional, non-sinusoidal ac voltage waveform that makes the high-frequency transformer design challenging. This paper proposes an optimized transformer design method by accurately estimating the transformer’s power loss for iM2DC converter while still utilizing the advantages associated with PS-SWM modulation. The findings are later validated by a down scaled prototype.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 236-240
Study of Passive dv/dt Filter and Proposed Active Solution for SiC MV Motor Drive
Overvoltage caused by the reflected wave phenomenon is well known in motor drive systems with long cables, which becomes worse for Medium Voltage (MV) SiC motor drive systems. Passive dv/dt filters are widely used to alleviate this overvoltage phenomenon. This paper mustrates the passive dv/dt filter limitations for SiC MV motor drive systems. In addition, an active solution with low power loss is proposed in this paper to suppress the overvoltage resulting from the reflected wave phenomenon in SiC MV motor drives. Both simulation and experimental results are presented to validate the proposed method.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 236-240
Study of Passive dv/dt Filter and Proposed Active Solution for SiC MV Motor Drive
Overvoltage caused by the reflected wave phenomenon is well known in motor drive systems with long cables, which becomes worse for Medium Voltage (MV) SiC motor drive systems. Passive dv/dt filters are widely used to alleviate this overvoltage phenomenon. This paper mustrates the passive dv/dt filter limitations for SiC MV motor drive systems. In addition, an active solution with low power loss is proposed in this paper to suppress the overvoltage resulting from the reflected wave phenomenon in SiC MV motor drives. Both simulation and experimental results are presented to validate the proposed method.
- Open Access
- 6 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (7) , 6004-6008
A Phase-Shifted Square Wave Modulation (PS-SWM) for Modular Multilevel Converter (MMC) and DC Transformer for Medium Voltage Applications
In this letter a phase-shifted square wave modulation (PS-SWM) strategy is proposed for modular multilevel converters (MMC) as well as DC transformers for medium voltage applications. The proposed technique can achieve a smaller cell capacitor size without increasing total device rating (TDR) and degrading dc current control capability. The operation principle of the proposed method is presented on an isolated modular multilevel dc-dc converter (iM2DC) which consists of MMC stage and applied as a DC transformer for medium voltage DC grid. The TDR and passive components sizing are derived and compared with those using other modulation methods. Finally a downscaled hardware prototype has been built and tested to verify the proposed modulation method.
- 6 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (7) , 6004-6008
Open AccessA Phase-Shifted Square Wave Modulation (PS-SWM) for Modular Multilevel Converter (MMC) and DC Transformer for Medium Voltage Applications
In this letter a phase-shifted square wave modulation (PS-SWM) strategy is proposed for modular multilevel converters (MMC) as well as DC transformers for medium voltage applications. The proposed technique can achieve a smaller cell capacitor size without increasing total device rating (TDR) and degrading dc current control capability. The operation principle of the proposed method is presented on an isolated modular multilevel dc-dc converter (iM2DC) which consists of MMC stage and applied as a DC transformer for medium voltage DC grid. The TDR and passive components sizing are derived and compared with those using other modulation methods. Finally a downscaled hardware prototype has been built and tested to verify the proposed modulation method.
- 9 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (1) , 13-19
Reduction of EMI Noise Due to Nonideal Interleaving in a 100 kW SiC PV Converter
A Grid-tied inverter utilizing wide bandgap (WBG) devices can achieve higher switching frequency resulting in a power filter with reduced size and weight. However the increased switching frequency may lead to more switching harmonics entering the electromagnetic interference (EMI) frequency range, which will increase the size of EMI filter. Interleaving paralleled converters can cancel some of the switching harmonics and reduce the size of EMI filter. However, non-ideal interleaving will deteriorate the harmonic canceling effect. In this research, the non-ideal effects are found to be from the small mismatch of the pulse-width of the interleaving legs and the mismatch of the impedance between the interleaving legs. A modulation method is proposed to completely eliminate the pulse width mismatch. Compared with other solutions, the proposed method does not require the information of filter parameters, nor gate driver synchronization, nor special function block of the digital controller. The proposed modulation was implemented on a 150MHz digital signal processor (DSP) and a 100MHz Field-programmable gate array (FPGA), and was experimentally verified on a 100kW parallel coupled SiC PV inverter prototype.
- 9 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (1) , 13-19
Reduction of EMI Noise Due to Nonideal Interleaving in a 100 kW SiC PV Converter
A Grid-tied inverter utilizing wide bandgap (WBG) devices can achieve higher switching frequency resulting in a power filter with reduced size and weight. However the increased switching frequency may lead to more switching harmonics entering the electromagnetic interference (EMI) frequency range, which will increase the size of EMI filter. Interleaving paralleled converters can cancel some of the switching harmonics and reduce the size of EMI filter. However, non-ideal interleaving will deteriorate the harmonic canceling effect. In this research, the non-ideal effects are found to be from the small mismatch of the pulse-width of the interleaving legs and the mismatch of the impedance between the interleaving legs. A modulation method is proposed to completely eliminate the pulse width mismatch. Compared with other solutions, the proposed method does not require the information of filter parameters, nor gate driver synchronization, nor special function block of the digital controller. The proposed modulation was implemented on a 150MHz digital signal processor (DSP) and a 100MHz Field-programmable gate array (FPGA), and was experimentally verified on a 100kW parallel coupled SiC PV inverter prototype.