Cenk Karakurt
Research Subjects
Cenk Karakurt has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Ferdi Şenol
Department of Civil Engineering, Faculty of Engineering, Bilecik Şeyh Edebali University, Bilecik, Turkey
4 shared publications - Mehmet Uğur Toprak
Kütahya Dumlupınar University, Engineering Faculty, Civil Engineering Department, Kütahya, Turkey
3 shared publications Nazım Çağatay Demiral
2 shared publications- Yıldırım Bayazıt
Department of Civil Engineering Bilecik Şeyh Edebali University Bilecik Türkiye
2 shared publications Ahmet Ferdi Şenol
1 shared publication- Ahmet Çelik
Department of Physics , Giresun University , Giresun, Turkey
1 shared publication
Latest Publications
- Open Access
- 1 December 2023
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 13 (4) , 2692-2705
Öğütülmüş Pişmiş Kil ve Mermer Atıklarının Çimentolu Harçlarda Dayanım Gelişimine Etkisi
Türkiye’deki nüfus artışı, yapıların hizmet ömrünün tamamlanması, kentsel dönüşümlerin uygulanması, yeni konut ve altyapı ihtiyaçları ile birlikte çimentoya olan talep istikrarlı bir şekilde artmaya devam etmektedir. Bununla birlikte çimento üretimindeki artış, yüksek karbon emisyonuna ve fazladan enerji tüketimine de sebep olmaktadır. Bu çalışmada, inşaat endüstrisindeki çimento kullanımını azaltmak, atık mermer ve inşaat yıkım sahaları kaynaklı çevre kirliliğini bertaraf etmek amacıyla, öğütülmüş pişmiş kil (K) ve mermer (M) atıklarının çimentolu harçlarda kullanımı araştırılmıştır. Bu amaçla tasarlanan harç serilerinde, çimento yerine ağırlıkça; %0 (kontrol), %5, %10 ve %15 oranlarında atık toz malzemeler kullanılarak yedi serilik harç karışımları üretilmiş, taze harç serilerinin işlenebilirlik özellikleri belirlendikten sonra üretilen numunelere; 7, 28, 56 ve 90 günlük standart kür uygulanarak fiziksel ve mekanik özellikleri araştırılmıştır. Taze harç serilerinde, K ikamesi arttıkça yayılma değerleri azalırken, M ikamesi arttıkça yayılma değerleri de artmıştır. Serilere uygulanan 90 günlük kür sonunda elde edilen en yüksek dayanım sonuçları kontrol serisine göre karşılaştırıldığında; çimento yerine %10 oranında K kullanılarak üretilen harçların basınç ve eğilme dayanımları sırasıyla; %8 ve %4 oranlarında artarken, %5 oranında M kullanılarak üretilen harçların dayanımları da %2 ve %4 oranlarında artmıştır.
- 1 December 2023
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 13 (4) , 2692-2705
Open AccessÖğütülmüş Pişmiş Kil ve Mermer Atıklarının Çimentolu Harçlarda Dayanım Gelişimine Etkisi
Türkiye’deki nüfus artışı, yapıların hizmet ömrünün tamamlanması, kentsel dönüşümlerin uygulanması, yeni konut ve altyapı ihtiyaçları ile birlikte çimentoya olan talep istikrarlı bir şekilde artmaya devam etmektedir. Bununla birlikte çimento üretimindeki artış, yüksek karbon emisyonuna ve fazladan enerji tüketimine de sebep olmaktadır. Bu çalışmada, inşaat endüstrisindeki çimento kullanımını azaltmak, atık mermer ve inşaat yıkım sahaları kaynaklı çevre kirliliğini bertaraf etmek amacıyla, öğütülmüş pişmiş kil (K) ve mermer (M) atıklarının çimentolu harçlarda kullanımı araştırılmıştır. Bu amaçla tasarlanan harç serilerinde, çimento yerine ağırlıkça; %0 (kontrol), %5, %10 ve %15 oranlarında atık toz malzemeler kullanılarak yedi serilik harç karışımları üretilmiş, taze harç serilerinin işlenebilirlik özellikleri belirlendikten sonra üretilen numunelere; 7, 28, 56 ve 90 günlük standart kür uygulanarak fiziksel ve mekanik özellikleri araştırılmıştır. Taze harç serilerinde, K ikamesi arttıkça yayılma değerleri azalırken, M ikamesi arttıkça yayılma değerleri de artmıştır. Serilere uygulanan 90 günlük kür sonunda elde edilen en yüksek dayanım sonuçları kontrol serisine göre karşılaştırıldığında; çimento yerine %10 oranında K kullanılarak üretilen harçların basınç ve eğilme dayanımları sırasıyla; %8 ve %4 oranlarında artarken, %5 oranında M kullanılarak üretilen harçların dayanımları da %2 ve %4 oranlarında artmıştır.
- 1 May 2023
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 75 (10) , 529-540
Investigation of erosive wear effect on concrete water structures: the case of Porsuk Dam, Turkey
Water structures usually consist of concrete surfaces. The concrete surfaces are subjected to erosive wear under the flow of water containing suspended sediment in high concentrations. Such flow-induced erosion is a significant problem for ageing structures because it can shorten their service lives. In this study, Böhme, ASTM C 1138 and newly developed sand–water jet abrasion test methods were used to determine the abrasion behaviour of different concrete types. Various mineral additives, such as fly ash (FA) and ground blast furnace slag (GBFS) were used to improve the wear resistance of the concrete specimens. In the study, the spillway of the Porsuk dam, Turkey, was chosen as a case study. By taking the spillway concrete recipe of this dam as a reference, its abrasion resistance was analysed for different mineral-added concrete recipes. According to the results of the study, it was observed that mixtures using 10% FA and GBFS considerably improved the resistance to abrasion.
- 1 May 2023
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 75 (10) , 529-540
Investigation of erosive wear effect on concrete water structures: the case of Porsuk Dam, Turkey
Water structures usually consist of concrete surfaces. The concrete surfaces are subjected to erosive wear under the flow of water containing suspended sediment in high concentrations. Such flow-induced erosion is a significant problem for ageing structures because it can shorten their service lives. In this study, Böhme, ASTM C 1138 and newly developed sand–water jet abrasion test methods were used to determine the abrasion behaviour of different concrete types. Various mineral additives, such as fly ash (FA) and ground blast furnace slag (GBFS) were used to improve the wear resistance of the concrete specimens. In the study, the spillway of the Porsuk dam, Turkey, was chosen as a case study. By taking the spillway concrete recipe of this dam as a reference, its abrasion resistance was analysed for different mineral-added concrete recipes. According to the results of the study, it was observed that mixtures using 10% FA and GBFS considerably improved the resistance to abrasion.
- 26 February 2023
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 27 (5) , 330-345
Effect of synthetic zeolite on tobermorite synthesis
Chemical anchors are widely used in additional installations of construction irons, repair and reinforcement work. Due to the increasing diversity of materials and the improved awareness of waste products, it has become possible to produce different kinds of concrete, with various properties. In this study, class B420C ribbed bars with 16 mm diameter, were installed in four different concretes by using four different chemical adhesives, and a tensile force was applied. The stiffness, displacement ductility ratio, energy-dissipation capability and tensile force values were determined and the failure modes were interpreted from the load-displacement curves, obtained as a result of the experiments. It was found that the tensile force and energy-dissipation capacity, had increased as a result of installing anchor and applying a tensile force to the concrete, that was obtained by adding admixture materials, to the reference concrete. In the analytical part of the study, the formulation provided in ACI 318 was used, capacity and design strengths were identified, and their safety levels were determined in comparison with the test results.
- 26 February 2023
- Published by Fundacja Cement Wapno Beton in Cement Wapno Beton
- Vol. 27 (5) , 330-345
Effect of synthetic zeolite on tobermorite synthesis
Chemical anchors are widely used in additional installations of construction irons, repair and reinforcement work. Due to the increasing diversity of materials and the improved awareness of waste products, it has become possible to produce different kinds of concrete, with various properties. In this study, class B420C ribbed bars with 16 mm diameter, were installed in four different concretes by using four different chemical adhesives, and a tensile force was applied. The stiffness, displacement ductility ratio, energy-dissipation capability and tensile force values were determined and the failure modes were interpreted from the load-displacement curves, obtained as a result of the experiments. It was found that the tensile force and energy-dissipation capacity, had increased as a result of installing anchor and applying a tensile force to the concrete, that was obtained by adding admixture materials, to the reference concrete. In the analytical part of the study, the formulation provided in ACI 318 was used, capacity and design strengths were identified, and their safety levels were determined in comparison with the test results.
- Open Access
- 31 December 2022
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 9 (2) , 918-930
Tuğla, Kiremit ve Mermer Atığı Tozları ile Üretilen Jeopolimer Harçların Özellikleri
Bu çalışmada çevre kirliliğini azaltmak amacı ile pişmiş kil (tuğla, kiremit) ve mermer atığı tozları jeopolimer harç üretiminde hammadde olarak kullanılmıştır. Bu amaçla, jeopolimer harçların taze ve sertleşmiş özelliklerine hammadde kullanım oranının ve kür sıcaklığının (60 ve 80 ℃) etkileri incelenmiştir. Pişmiş kil tozu (%50) ve mermer tozu (%50) beraber kullanılarak hazırlanan jeopolimer harç, %100 kil tozu ile üretilene göre %40 fazla yayılma göstermiştir. Jeopolimer harçların 7 günlük basınç dayanımları, 28 günlük dayanımlarının yaklaşık %90’ına ulaşmıştır. En yüksek basınç dayanımı (28,50 MPa), %100 pişmiş kil tozu kullanılarak üretilen ve 80 ℃’ de kür uygulanan 28 günlük jeopolimer harçlarda görülmüştür.
- 31 December 2022
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 9 (2) , 918-930
Open AccessTuğla, Kiremit ve Mermer Atığı Tozları ile Üretilen Jeopolimer Harçların Özellikleri
Bu çalışmada çevre kirliliğini azaltmak amacı ile pişmiş kil (tuğla, kiremit) ve mermer atığı tozları jeopolimer harç üretiminde hammadde olarak kullanılmıştır. Bu amaçla, jeopolimer harçların taze ve sertleşmiş özelliklerine hammadde kullanım oranının ve kür sıcaklığının (60 ve 80 ℃) etkileri incelenmiştir. Pişmiş kil tozu (%50) ve mermer tozu (%50) beraber kullanılarak hazırlanan jeopolimer harç, %100 kil tozu ile üretilene göre %40 fazla yayılma göstermiştir. Jeopolimer harçların 7 günlük basınç dayanımları, 28 günlük dayanımlarının yaklaşık %90’ına ulaşmıştır. En yüksek basınç dayanımı (28,50 MPa), %100 pişmiş kil tozu kullanılarak üretilen ve 80 ℃’ de kür uygulanan 28 günlük jeopolimer harçlarda görülmüştür.
- Open Access
Rheological and Durability Properties of Self-Compacting Concrete Produced Using Marble Dust and Blast Furnace Slag
Self-compacting concrete (SCC) is a special, highly fluid type of concrete that is produced using chemical additives. It is easier to pour and reduces defects arising from workability. Waste marble dust is generated during the production of marble using different methods, or during the cutting of marble in processing plants; however, the uncontrolled disposal of waste marble dust in nature is associated with some environmental problems. Cement and concrete technology is a field with potential for the utilization of these large amounts of waste. The present study explores the use of marble dust (MD) (an industrial waste generated in abundance around the province of Bilecik) and granulated blast furnace slag (GBFS) (another industrial waste product) in the production of SCC. In this study, MD and GBFS are used as fine materials in SCC mixtures, and the rheological and workability properties and other hardened concrete properties of the produced SCC specimens are tested. Additional tests are conducted to identify the durability of the specimens to sulfate attack, as well as their freeze–thaw and abrasion resistance, followed by microstructure tests to identify the effects of MD and GBFS on bond structure. The late-age performances of MD and GBFS were then examined based on the results of the durability tests. The presented results revealed improvements in the fresh and hardened properties of SCC produced using MD and GBFS.
Open AccessRheological and Durability Properties of Self-Compacting Concrete Produced Using Marble Dust and Blast Furnace Slag
Self-compacting concrete (SCC) is a special, highly fluid type of concrete that is produced using chemical additives. It is easier to pour and reduces defects arising from workability. Waste marble dust is generated during the production of marble using different methods, or during the cutting of marble in processing plants; however, the uncontrolled disposal of waste marble dust in nature is associated with some environmental problems. Cement and concrete technology is a field with potential for the utilization of these large amounts of waste. The present study explores the use of marble dust (MD) (an industrial waste generated in abundance around the province of Bilecik) and granulated blast furnace slag (GBFS) (another industrial waste product) in the production of SCC. In this study, MD and GBFS are used as fine materials in SCC mixtures, and the rheological and workability properties and other hardened concrete properties of the produced SCC specimens are tested. Additional tests are conducted to identify the durability of the specimens to sulfate attack, as well as their freeze–thaw and abrasion resistance, followed by microstructure tests to identify the effects of MD and GBFS on bond structure. The late-age performances of MD and GBFS were then examined based on the results of the durability tests. The presented results revealed improvements in the fresh and hardened properties of SCC produced using MD and GBFS.
- Open Access
- 1 January 2022
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 21 (1) , 145-155
Effect of aggregate size and polyethylene sheet curing on me-chanical and microstructural properties of lightweight expanded clay aggregate concrete
This study assessed the effect of lightweight expanded clay aggregate (LECA) grain size and curing with polyethylene concrete curing film (PCCF) on microstructure, interfacial transition zone (ITZ), and compressive strength of structural lightweight aggregate concrete (LWAC) produced with two different Dmax (16 or 22.4 mm). To this end, 2 series of normal weight aggregate concretes (NWAC) and 6 series of LWAC incorporating 40% by vol. unprewetted LECA having (0-3, 3-8, or 8-16 mm) grain sizes were evaluated by using unit weight, compressive strength tests at 1, 7, and 28 days and SEM-EDX observations. Preventing the moisture loss from fresh concrete through PCCF curing had positive effects on compressive strength up to 14 and 9% for 1 and 28 days respectively. Shell thickness of LECA considerably increased with the decrease in LECA grain size. Thus, the compressive strength of LECA and LWAC increased by the decrease in LECA grain size. LWAC containing 0-3 mm LECA, achieved up to 21% higher compressive strength to weight ratio compared with the NWAC with the aid of the pozzolanic reactivity of fine LECA particles.
- 1 January 2022
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 21 (1) , 145-155
Open AccessEffect of aggregate size and polyethylene sheet curing on me-chanical and microstructural properties of lightweight expanded clay aggregate concrete
This study assessed the effect of lightweight expanded clay aggregate (LECA) grain size and curing with polyethylene concrete curing film (PCCF) on microstructure, interfacial transition zone (ITZ), and compressive strength of structural lightweight aggregate concrete (LWAC) produced with two different Dmax (16 or 22.4 mm). To this end, 2 series of normal weight aggregate concretes (NWAC) and 6 series of LWAC incorporating 40% by vol. unprewetted LECA having (0-3, 3-8, or 8-16 mm) grain sizes were evaluated by using unit weight, compressive strength tests at 1, 7, and 28 days and SEM-EDX observations. Preventing the moisture loss from fresh concrete through PCCF curing had positive effects on compressive strength up to 14 and 9% for 1 and 28 days respectively. Shell thickness of LECA considerably increased with the decrease in LECA grain size. Thus, the compressive strength of LECA and LWAC increased by the decrease in LECA grain size. LWAC containing 0-3 mm LECA, achieved up to 21% higher compressive strength to weight ratio compared with the NWAC with the aid of the pozzolanic reactivity of fine LECA particles.