Ahmet Ferdi Şenol
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmet Ferdi Şenol has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Cenk Karakurt
BİLECİK ŞEYH EDEBALİ ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, İNŞAAT MÜHENDİSLİĞİ BÖLÜMÜ
4 shared publications Özlem Çalışkan
3 shared publications- Özlem Çalışkan
Bilecik Şeyh Edebali Üniversitesi
3 shared publications - Ali Ozer
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
1 shared publication - Fatih Apaydin
Department of Metallurgical and Materials Engineering, Faculty of Engineering, Bilecik Şeyh Edebali University, Bilecik, Turkey
1 shared publication - Manolya Kandemir
Demişas Döküm Emaye Mamulleri Sanayi A.Ş., Bilecik, Turkey
1 shared publication
Latest Publications
- Open Access
- 9 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
High-temperature mechanical performance and microstructural insights of polypropylene fiber-reinforced fly ash–slag geopolymer mortars
- 9 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessHigh-temperature mechanical performance and microstructural insights of polypropylene fiber-reinforced fly ash–slag geopolymer mortars
- 8 December 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 15 (1) , 1
Effect of eggshell powder calcined at different temperatures on the workability and mechanical properties of cement-based mortars
In this study, the incorporation of waste eggshell powder (ESP), a calcium carbonate (CaCO₃)-rich by-product of the food industry, into cement-based mortars was investigated. Eggshells were ground and calcined at 800 °C and 900 °C for two hours to produce ESP800 and ESP900. ESP replaced cement at 5%, 10%, and 15% by weight, yielding seven mortar mixtures. Thermal and microstructural properties were examined by TG/DSC, FE-SEM, and XRD. Workability was assessed with the flow table test, and specimens cured for 7 and 28 days were tested for ultrasonic pulse velocity (UPV), flexural strength (FS), and compressive strength (CS). Calcination temperature and replacement level significantly influenced performance. At 5% replacement, ESP900-5 achieved the best results, with a 28-day CS of 45.6 MPa, 9.9% higher than the control. At 15% replacement, FS decreased by 19% (ESP800) and 9% (ESP900), and CS decreased by 27.5% and 20%, respectively. UPV indicated denser matrices up to 10% replacement, with porosity increasing at 15%. Statistical analysis showed curing duration as the most influential positive factor, replacement ratio as the strongest negative effect, and calcination temperature as consistently beneficial. Multiple linear regression and ANOVA confirmed the statistical significance of these variables and demonstrated high predictive accuracy (R2 > 0.9).
- 8 December 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 15 (1) , 1
Effect of eggshell powder calcined at different temperatures on the workability and mechanical properties of cement-based mortars
In this study, the incorporation of waste eggshell powder (ESP), a calcium carbonate (CaCO₃)-rich by-product of the food industry, into cement-based mortars was investigated. Eggshells were ground and calcined at 800 °C and 900 °C for two hours to produce ESP800 and ESP900. ESP replaced cement at 5%, 10%, and 15% by weight, yielding seven mortar mixtures. Thermal and microstructural properties were examined by TG/DSC, FE-SEM, and XRD. Workability was assessed with the flow table test, and specimens cured for 7 and 28 days were tested for ultrasonic pulse velocity (UPV), flexural strength (FS), and compressive strength (CS). Calcination temperature and replacement level significantly influenced performance. At 5% replacement, ESP900-5 achieved the best results, with a 28-day CS of 45.6 MPa, 9.9% higher than the control. At 15% replacement, FS decreased by 19% (ESP800) and 9% (ESP900), and CS decreased by 27.5% and 20%, respectively. UPV indicated denser matrices up to 10% replacement, with porosity increasing at 15%. Statistical analysis showed curing duration as the most influential positive factor, replacement ratio as the strongest negative effect, and calcination temperature as consistently beneficial. Multiple linear regression and ANOVA confirmed the statistical significance of these variables and demonstrated high predictive accuracy (R2 > 0.9).
- 15 October 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (4) , 1282-1292
Flexural Performance of concrete beams strengthened with textile reinforced mortars: Influence of application pattern and repair mortar type
This study examines the effectiveness of textile-reinforced mortar (TRM) systems incorporating a ground granulated blast furnace slag-based geopolymer mortar and a commercially available cement-based repair mortar in enhancing the flexural performance of normal-strength concrete beams. TRM applications were implemented with varying coverage patterns and surface areas, while steel fibers were added to the concrete mixtures at dosages of 0.3% and 0.6% by volume for comparative purposes. Experimental evaluations—including flexural strength, load–displacement behavior, initial stiffness, ductility, and energy dissipation capacity—revealed that full-coverage TRM applications enhanced load-bearing capacity by up to 24%. Geopolymer-based TRM systems exhibited comparable or even superior performance to their cement-based counterparts under both full and partial coverage conditions. While the incorporation of 0.6% steel fiber contributed to modest improvements in ductility and energy absorption, it also resulted in a significant reduction in initial stiffness. These findings highlight that TRM systems—particularly when applied with optimized coverage geometry and appropriate binder type—constitute an effective and sustainable strategy for improving the flexural response of reinforced concrete elements.
- 15 October 2025
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 14 (4) , 1282-1292
Flexural Performance of concrete beams strengthened with textile reinforced mortars: Influence of application pattern and repair mortar type
This study examines the effectiveness of textile-reinforced mortar (TRM) systems incorporating a ground granulated blast furnace slag-based geopolymer mortar and a commercially available cement-based repair mortar in enhancing the flexural performance of normal-strength concrete beams. TRM applications were implemented with varying coverage patterns and surface areas, while steel fibers were added to the concrete mixtures at dosages of 0.3% and 0.6% by volume for comparative purposes. Experimental evaluations—including flexural strength, load–displacement behavior, initial stiffness, ductility, and energy dissipation capacity—revealed that full-coverage TRM applications enhanced load-bearing capacity by up to 24%. Geopolymer-based TRM systems exhibited comparable or even superior performance to their cement-based counterparts under both full and partial coverage conditions. While the incorporation of 0.6% steel fiber contributed to modest improvements in ductility and energy absorption, it also resulted in a significant reduction in initial stiffness. These findings highlight that TRM systems—particularly when applied with optimized coverage geometry and appropriate binder type—constitute an effective and sustainable strategy for improving the flexural response of reinforced concrete elements.
- Open Access
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
The effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
Open AccessThe effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- Open Access
- 6 April 2025
- Published by Elsevier in Hybrid Advances
- Vol. 10
Performance of geopolymer mortar incorporating spent coffee grounds as a recycled building material: An experimental and predictive analysis
- 6 April 2025
- Published by Elsevier in Hybrid Advances
- Vol. 10
Open AccessPerformance of geopolymer mortar incorporating spent coffee grounds as a recycled building material: An experimental and predictive analysis