Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dogan Engin Alnak has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Cooling System Analysis of Gas Turbine Blades Manufactured Using Different Material Types

    by İbRahim Can, Serdar Mercan, Dogan Engin Alnak, Muhammed Sipahi

    One of the major challenges in gas turbine engines is that the blades operate at temperatures higher than the melting points of the materials they are made of. Researchers have focused on developing materials that can withstand high temperatures and designing effective cooling systems for the blades. Although there are limitations to the improvements that can be achieved through material technology, the importance of cooling is clear, and it is considered a critical factor for achieving high efficiency in turbines. To this end, two cooling models were developed using different materials, and the heat transfer in the blades was analyzed numerically using the SolidWorks package program and Ansys. The study considered titanium carbide (TiC) and third-generation single crystal super-alloy CMSX-10 materials. The blade designs were proposed based on the analysis results. The analysis showed that the enhanced model performed better when used with CMSX-10 material in terms of thermal properties.

  • Investigation of Heat Transfer Increment in Electronic System Surfaces by Different Air Jet Impingement Applications

    by D. E. Alnak, K. Karabulut

    The impinging jet technique is a high-performance cooling technology for microchips which are basic elements of electronic systems and having high heat generation rates in small volumes. In this study, the improvement of heat transfer of the microchips used in all technological products today by air impinging jet has been examined. For this purpose, numerical research has been carried out on the cooling of copper plate surfaces with two different patterns, reverse triangle and reverse semi-circle shaped having 1000 W/m2 constant heat flux in rectangular cross-section ducts with adiabatic surfaces, by one and double air jets with distances of D\(_{h}\) and 2D\(_{h}\) between them. Numerical computation has been performed for energy and Navier–Stokes equations as steady and three-dimensional by employing the Ansys-Fluent computer program with the k-\(\varepsilon\) turbulence model. The obtained results have been compared with the numerical and experimental results of the study in the literature and it has been seen that they are compatible with each other. The results have been presented as the mean Nu number and the variation of surface temperature for each of both patterned surfaces in single and double jet channels with different distances. Streamline and temperature contour distributions of the jet flow along the channel for different H/D\(_{h}\) ratios and jet numbers have been evaluated for both patterned surfaces. In double-jet and 2D\(_{h}\) distance channels compared to D\(_{h}\), at H/D\(_{h}\) = 12 and Re = 11,000, the Nu number increases of 67% and 65.9% have been observed on the first-row reverse triangle and semi-circular patterned surfaces, respectively.


  • Open Access

    Elmas-Su Nanoakışkanı Kullanılan Kanatçıklı ve Farklı Yükseklikli Birleşik Jet Akışlı Kanallarda Yüzeylerin Soğutulması

    by Koray Karabulut, Dogan Engin Alnak

    Çarpan jet-çapraz akıştan oluşan birleşik jet etkisi elektronik elemanların soğutma performansını artırıcı bir etkiye sahiptir. Bu çalışmada, birleşik jet akışıyla kanatçıksız ve 30o açıya sahip kanatçıklı, N=2D kanatçık mesafeli ve H=3D ve 4D yükseklikli kanallarda su ve %2 hacimsel konsantrasyonlu Elmas-Su nanoakışkanı kullanılmasıyla küp ve yamuk modelli yüzeylerden olan ısı transferi ve performans analizi sayısal olarak incelenmiştir. Sayısal araştırma, sürekli ve üç boyutlu, k-ε türbülans modelli Ansys-Fluent programıyla gerçekleştirilmiştir. Literatürdeki çalışmalar gözetilerek kanal boyutlarına uygun olarak kanallara üçer adet model yerleştirilmiştir. Kanaldaki akışkanların Re sayısı aralığı 5000-9000’ dir. Sonuçlar, literatürdeki deneysel çalışmanın Nu sonuçlarıyla kıyaslanmış ve uyumlu oldukları belirlenmiştir. Çalışmanın sonuçları, kanallardaki her bir model için ortalama Nu sayısı ve yüzey sıcaklığının değişimleri olarak su ve nanoakışkan için kanatçıksız ve kanatçıklı durumlarda farklı kanal yüksekliklerinde karşılaştırmalı olarak incelenmiştir. Ayrıca, birleşik jet nanoakışkan akışının hız ve sıcaklık konturu dağılımları sunulmuştur. Bununla birlikte, kanallardaki her üç model yüzeyinin tümü için farklı Reynolds sayılarında performans değerlendirme sayıları (PEC) ve Re=7000 için ortalama Nu sayısı (Num) ve yüzey sıcaklık değerleri (Tm) değerlendirilmiştir. H=3D ve kanatçıklı kanalda Elmas-Su nanoakışkanının kullanılması kanatçıksız ve su akışkanı kullanılan kanala göre küp ve yamuk modelli yüzeylerde Num değerlerinin sırasıyla %24,14 ve %18,91 daha fazla olmasını sağlamıştır.


  • CFD Analysis of an Aircraft Turbofan Engine Combustion Process and the Effect on Turbine

    by İbrahim Can, Dogan Engin Alnak, Muhammed Si̇pahi̇

    In this paper, a two-dimensional computational fluid dynamics (CFD) study of Turbofan engine is presented using the ANSYS Fluent program, the navier–stokes equations is used for analysis, including a two-dimensional and symmetrical drawing of both the combustion chamber and in a 1.5 Stage Axial Flow Turbine. A GE-90 turbofan engine nacelle was used with Naca 63-412 type blades were used for the analysis of the flow on the turbine blades. Combustion chamber simulations were carried out using a previous study. The computational results were compared with other studies on the Exergetic analysis of a GE-21 turbojet engine. The GE-21 engine had a combustion chamber temperature of 2900 K, while the GE-90 engine had a temperature of around 2706 K. The previous study considered the velocity of fluid flow to be 200 m/s, whereas the velocity of flow in this study was 209 m/s as determined in the part of analysis and result.

  • Grafen Oksit (GO)-Su Nanoakışkanlı ve Kanatçıklı Birleşik Jet Akışlı Kanallarda Isı Transferinin Araştırılması

    by Dogan Engin Alnak, Koray Karabulut

    Bu çalışmada, birleşik jet akışıyla kanatçıksız ve farklı kanatçık mesafeli (N = D ve 2D) ve 60o açılı kanallarda su ve %0.02 hacimsel konsantrasyonlu GO (Grafen Oksit)-Su nanoakışkanı kullanılmasıyla yamuk ve taç desenli yüzeylerden olan ısı transferi ve performans analizi sayısal olarak incelenmiştir. Sayısal araştırma, zamandan bağımsız ve üç boyutlu, k-ε türbülans modelli Ansys-Fluent programıyla gerçekleştirilmiştir. Çalışmanın sonuçları, literatürdeki deneysel çalışmanın Nu sonuçlarıyla kıyaslanmış ve uyumlu oldukları görülmüştür. N = 2D ve Re = 15000’ de her üç yamuk ve taç desenli yüzeylerde nanoakışkanın ortalama Num sayılarının kanatçıksız ve su akışkanına göre sırasıyla %18.35 ve %24.09 daha fazla olduğu bulunmuştur.

  • Open Access

    Farklı Desenli Bakır Plakaların Birleşik Jet Akışı ile Soğutulmasında Grafen Oksit (GO)-Su Nanoakışkanının Etkisi

    by Koray Karabulut, Dogan Engin Alnak

    Minyatürleşen enerji sistemleri ve yüksek güçlü elektronik aletler soğutma kapasitesi yüksek olan sistemlerin kullanımını gerektirmektedir. Çarpan jet-çapraz akıştan oluşan birleşik jet etkisi mikroçip elektronik elemanlarının soğutma performansını artırıcı bir etkiye sahiptir. Bu çalışmada, kanallarda bulunan sabit 1000 W/m2 ısı akılı küp ve oyuklu desenlerin su ve %0,02 hacimsel nanoparçacık konsantrasyonlu GO (Grafen Oksit)-Su nanoakışkanı kullanılarak birleşik jet akışı ile soğutulması sayısal olarak analiz edilmiştir. Sayısal çalışma, sürekli ve üç boyutlu olarak k-ε türbülans modelli Ansys-Fluent programının kullanılmasıyla gerçekleştirilmiştir. Nanoakışkanın termofiziksel özellikleri deneysel olarak elde edilmiştir. Literatürdeki çalışmalar da göz önüne alınarak kanal boyutlarına uygun olacak şekilde kanallara üçer adet desenli yüzey yerleştirilmiştir. Kanallara ayrıca jet girişinden itibaren D jet giriş çapı ölçüsünde sabit bir uzaklıkta (N) 90o açılı kanatçık eklenmiştir. Kanal yükseklikleri 3D ve 6D iken akışkanların Re sayısı aralığı 5000-9000’ dir. Çalışmadan elde edilen sonuçların doğruluğu ve kabul edilebilirliği deneysel araştırmalar sonucu elde edilen eşitlik kullanılarak kanıtlanmıştır. Çalışmanın sonuçları, kanallardaki her bir desen için ortalama Nu sayısı ve yüzey sıcaklığının değişimleri olarak su ve nanoakışkan için kanatçıksız ve kanatçıklı durumlarda karşılaştırmalı olarak incelenmiştir. Ayrıca, birleşik jet nanoakışkan akışının hız ve sıcaklık konturu dağılımları jet-desen arası etkileşimler de göz önüne alınarak farklı kanal yükseklikleri için sunulmuştur. Bununla birlikte, kanallardaki her üç desenli yüzeyin tümü için farklı Reynolds sayılarında performans değerlendirme sayıları (PEC) ve ortalama Nu sayısı (Num) ve yüzey sıcaklık değerleri (Tm) Re = 9000 için değerlendirilmiştir. Re = 9000 ve H = 3D için GO-Su nanoakışkanlı kanatçıklı birleşik jet akışlı kanalda su akışkanlı ve kanatçıksız kanala göre küp ve oyuklu desen yüzeyleri için Num değerinde sırasıyla %45,04 ve %37,11’ lik artışlar elde edilmiştir. Bununla birlikte, Re = 5000 değerinde ve H = 3D yükseklikli kanallarda su akışkanı için PEC sayısı değerlerinin sırasıyla küp ve oyuklu desenli yüzeylerde nanoakışkana göre %1,69 ve %1,74 daha fazla oldukları tespit edilmiştir.


  • Research of cooling performance in combined jet flow channels using different nanofluids

    by Doğan Engin Alnak

    In this work, heat transfer from the cube and circular hollow-shaped copper plate surfaces with a constant heat flux of 1000 W/m 2 was numerically investigated by using a combination of the cross-flow-impinging jet. Numerical research was performed by solving the energy and Navier-Stokes equations as three-dimensional and steady, using the Ansys-Fluent computer program with the k-ε turbulence model. In order to direct the combined jet flow in the channel to the heated surfaces, the fins with 30 o and 60 o angles were placed in the channel horizontally with the impinging jet surface. While the channel height ( H ) is 4D, the distance of the fin from the jet inlet ( N ) is 2D. Fluids used in the channels are water, 0.02% GO-water and 2% diamond-water. The upper and lower surfaces of the channel and the fin are adiabatic and the flow Reynolds number range is 5000–15,000. The results of the work were compared with the experimental results of the studies in the literature and they were found to be consistent with each other. The results were presented as the mean Nu number and mean surface temperature variations for each model surface. Besides, the velocity and temperature contour distributions of the combined jet flow along the channel for diamond-water nanofluid were evaluated. Also, performance evaluation coefficient and average Nu number (Nu m ), and surface temperature values (T m ) were evaluated at different Reynolds numbers for all three patterned surfaces in the channels. At Re = 15,000, there are 18.42% and 17.08% increments in Nu m value for cube and circular hollow model surfaces in the channel with 60 o fin and GO-water nanofluid compared to the channel with water flow and without fin.


  • Numerical Investigation of The Effect of Impeller Blade Angle for Stirred Tank

    by Dogan Engin Alnak, Ferhat Koca, Yeliz Alnak

    In this study, the most widely used Rushton turbine in the industry was discussed, and the effect of different blade angles on the mixture was investigated numerically. As a standard model, 6 bladed propellers were used and 4 baffles were placed in the stirred tank. The selected tank model is in the form of a flat bottom cylindrical container. Flow characteristics were obtained by giving angles (10°, 20°, 30°, 40°, 50°, 60°) to the propeller blades used in the straight model. The obtained results were compared with each other. In addition, analyzes were repeated at different rotation speeds (600 rpm, 750 rpm, 1000 rpm) for each model at each angle. ANSYS Fluent 18 commercial software, which is the most preferred CFD program in the literature, was used for this numerical study. The analyzes were provided in the standard k-epsilon (ε) turbulence model. The Multiple Reference Frame (MRF) approach was used to simulate impeller rotation. The velocity profiles obtained from the simulations have been shown to be in consistent with the experimental estimates and the results of previous studies. As a result, it has been revealed that the best mixing balance is provided by the impeller blade at 40 and 50 degrees.


  • Search of the Effect of Jet Inlet Width on Heat Transfer and Flow Character

    by Doğan Engin ALNAK, Koray Karabulut

    Bu çalışmada, farklı jet giriş genişliklerindeki kanallarda bulunan düz yamuk ve ters yarım daire şeklinde iki farklı desene sahip bakır plakalı yüzeylerden hava jeti akışı ile olan ısı transferi sayısal olarak araştırılmıştır. Sayısal hesaplamalar, zamandan bağımsız ve üç boyutlu olarak enerji ve Navier-Stokes denklemlerinin k-ε türbülans modelli Ansys-Fluent bilgisayar programı kullanılarak çözülmesiyle gerçekleştirilmiştir. Kanalların üst ve alt yüzeyleri adyabatik olup desenli yüzeylere sabit ısı akısı uygulanmıştır. Jet giriş genişlikleri Dh ve 1,25Dh’dır. Çalışmanın sonuçları, literatürdeki çalışmanın sayısal ve deneysel sonuçlarıyla karşılaştırılmış ve birbirleriyle uyumlu oldukları görülmüştür. Sonuçlar, her bir desenli yüzey için ortalama Nu sayısı ve yüzey sıcaklık değişimi olarak sunulmuştur. Jet ve plaka arası mesafe (H/Dh) 12’de Re=9000 için ters yarım daire desenli yüzeylerin ortalama Nu sayısı, düz yamuk desenli yüzeylerden yaklaşık %56 daha fazladır.