Jiali Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiali Zhao has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Bobo Shen
School of Mechanical and Electrical Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Dan Wu
School of Mechanical and Electrical Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Liang Zhang
School of Mechanical and Electrical Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Liang Zhang
School of Mechanical and Electrical Engineering, Lanzhou University of Technology 2 , Lanzhou 730050
2 shared publications Xuesong Teng
Lanzhou University of Technology
2 shared publicationsBobo Shen
Lanzhou University of Technology
1 shared publication
Latest Publications
- Open Access
- 25 November 2024
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 8 (2)
Analysis of circularity metrology of small cylindrical workpiece with a segmenting scan method
Owing to eccentricity and inclination, circularity of a cylindrical workpiece cannot be measured precisely by a circularity measuring machine when the workpiece has a small dimension (diameter ≤ 3 mm). In this paper, with the aim of solving this problem, circularity metrology of a small cylindrical workpiece using a segmenting scanning method is analyzed. The cross-sectional circle of the cylinder is segmented into several equivalent arcs for measurement by a two-dimensional coordinate measuring machine (profilometer). The circularity contour is obtained by stitching together arc contours obtained by data processing of the coordinates. Different segmenting patterns for coordinate scanning are considered. Measurement results are presented for three segmentation patterns, with 8, 10, and 12 equal segments, respectively. These results are evaluated in terms of the matching coefficient between neighboring arc contours on circumferential stitching, the Euclidean distance between neighboring arc contours on radial stitching, and the curvature of the arcs. From these evaluations, it is found that as the number of segments is increased, the matching coefficient increases from 0.14 to 0.50, the Euclidean distance decreases from 32 nm to 26 nm, and the curvature becomes close to the standard value.
- 25 November 2024
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 8 (2)
Open AccessAnalysis of circularity metrology of small cylindrical workpiece with a segmenting scan method
Owing to eccentricity and inclination, circularity of a cylindrical workpiece cannot be measured precisely by a circularity measuring machine when the workpiece has a small dimension (diameter ≤ 3 mm). In this paper, with the aim of solving this problem, circularity metrology of a small cylindrical workpiece using a segmenting scanning method is analyzed. The cross-sectional circle of the cylinder is segmented into several equivalent arcs for measurement by a two-dimensional coordinate measuring machine (profilometer). The circularity contour is obtained by stitching together arc contours obtained by data processing of the coordinates. Different segmenting patterns for coordinate scanning are considered. Measurement results are presented for three segmentation patterns, with 8, 10, and 12 equal segments, respectively. These results are evaluated in terms of the matching coefficient between neighboring arc contours on circumferential stitching, the Euclidean distance between neighboring arc contours on radial stitching, and the curvature of the arcs. From these evaluations, it is found that as the number of segments is increased, the matching coefficient increases from 0.14 to 0.50, the Euclidean distance decreases from 32 nm to 26 nm, and the curvature becomes close to the standard value.
- Open Access
- 11 August 2023
- Published by Springer Nature in Research Square
Wafer Contour Curve Linearization Algorithm Research Based on Image for Detecting Minute Edge Defects
Aiming at the shortcomings of the existing wafer defect detection algorithms and the problem of low accuracy of wafer defect detection in the case of insufficient training samples, a wafer contour curve refinement extraction and linearization processing algorithm were developed for detecting minute edge defects. A new adaptive wafer image contrast enhancement algorithm was used to filter background noise, and the angle division method was used to rotate a wafer with any inclination to make it vertical. The target lines were extracted by using a single-pixel wide morphological convolution kernel, and then the wafer outline skeletal filling algorithm was proposed to make all the pixels of the extracted independent lines lie in the same rectangle when the lines meet the requirements. Finally, the length of the wafer contour straight lines was calculated based on the average value of two lines. Experiments show that the wafer contour straight lines extracted by this method can achieve a more precise coincidence with the original image. In this paper, an alternative algorithm, based on the image edge, especially when turning the contour curve into a straight line, is proposed for detecting the minute edge defects.
- 11 August 2023
- Published by Springer Nature in Research Square
Open AccessWafer Contour Curve Linearization Algorithm Research Based on Image for Detecting Minute Edge Defects
Aiming at the shortcomings of the existing wafer defect detection algorithms and the problem of low accuracy of wafer defect detection in the case of insufficient training samples, a wafer contour curve refinement extraction and linearization processing algorithm were developed for detecting minute edge defects. A new adaptive wafer image contrast enhancement algorithm was used to filter background noise, and the angle division method was used to rotate a wafer with any inclination to make it vertical. The target lines were extracted by using a single-pixel wide morphological convolution kernel, and then the wafer outline skeletal filling algorithm was proposed to make all the pixels of the extracted independent lines lie in the same rectangle when the lines meet the requirements. Finally, the length of the wafer contour straight lines was calculated based on the average value of two lines. Experiments show that the wafer contour straight lines extracted by this method can achieve a more precise coincidence with the original image. In this paper, an alternative algorithm, based on the image edge, especially when turning the contour curve into a straight line, is proposed for detecting the minute edge defects.
- Open Access
- 9 August 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (16) , 9091
Measurement Uncertainty Analysis of the Stitching Linear-Scan Method for the Measurable Dimension of Small Cylinders
A stitching linear scan method is proposed for roundness and diameter measurement of small cylindrical workpieces instead of the conventional rotary scan method due to the crucial alignments of eccentricity and inclination. To verify the reliability of the proposed method, by which the coordinates of the cross-sectional circle of a small cylinder is divided into several equal parts to be obtained and reconstructed, the diameter and roundness measurement uncertainties of the small cylinders with a diameter 1.5 mm are evaluated to be 0.047 μm and 0.095 μm, respectively, which can meet the uncertainty target of 0.1 μm. To investigate the measurable dimension by the proposed method, measurement uncertainty analysis of the small cylinders with various dimensions has been conducted according to the previous evaluation, since all the procedures are the same except for the uncertainty of X coordinates, which changes with the measured dimension’s change. The results show that the small cylinders with a diameter range from 0.01 mm to 50 mm can be measured by the proposed method when the position error θZ is reduced to the corresponding value. There is no measuring limitation set by the proposed model theoretically in the case of θX = θZ = 0.1°, while the machine has a measuring limitation.
- 9 August 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (16) , 9091
Open AccessMeasurement Uncertainty Analysis of the Stitching Linear-Scan Method for the Measurable Dimension of Small Cylinders
A stitching linear scan method is proposed for roundness and diameter measurement of small cylindrical workpieces instead of the conventional rotary scan method due to the crucial alignments of eccentricity and inclination. To verify the reliability of the proposed method, by which the coordinates of the cross-sectional circle of a small cylinder is divided into several equal parts to be obtained and reconstructed, the diameter and roundness measurement uncertainties of the small cylinders with a diameter 1.5 mm are evaluated to be 0.047 μm and 0.095 μm, respectively, which can meet the uncertainty target of 0.1 μm. To investigate the measurable dimension by the proposed method, measurement uncertainty analysis of the small cylinders with various dimensions has been conducted according to the previous evaluation, since all the procedures are the same except for the uncertainty of X coordinates, which changes with the measured dimension’s change. The results show that the small cylinders with a diameter range from 0.01 mm to 50 mm can be measured by the proposed method when the position error θZ is reduced to the corresponding value. There is no measuring limitation set by the proposed model theoretically in the case of θX = θZ = 0.1°, while the machine has a measuring limitation.
- Open Access
- 12 July 2023
- Published by MDPI AG in Preprints.org
Measurement Uncertainty Analysis of the Stitching Linear-Scan Method for the Measurable Dimension of Small Cylinders
To verify the reliability of the proposed stitching linear scan method for roundness measurement of small cylindrical workpieces, measurement uncertainties of the workpieces with various dimension are conducted. The cross-sectional circle of a cylindrical workpiece is divided into several equal arcs to be measured. Thus, the arc profile can be characterized according to the measured arcs. The roundness profile of the cylindrical part can be obtained by stitching these arc profiles together. Firstly, the measurement uncertainty of the workpiece with a diameter 1.5 mm and length 5.8 mm is evaluated to be 0.095 μm which can meet the uncertainty target of 0.1 μm. Considering the uncertainty of θx and θz which are the alignment around X-axis and Z-axis respectively changing with workpiece dimension changing, relevant uncertainties are carried out. As a result, there is no limitation with respect to workpiece diameter theoretically If the alignment can reach θz = θx = ±0.1° without considering the measurable range of the machine.
- 12 July 2023
- Published by MDPI AG in Preprints.org
Open AccessMeasurement Uncertainty Analysis of the Stitching Linear-Scan Method for the Measurable Dimension of Small Cylinders
To verify the reliability of the proposed stitching linear scan method for roundness measurement of small cylindrical workpieces, measurement uncertainties of the workpieces with various dimension are conducted. The cross-sectional circle of a cylindrical workpiece is divided into several equal arcs to be measured. Thus, the arc profile can be characterized according to the measured arcs. The roundness profile of the cylindrical part can be obtained by stitching these arc profiles together. Firstly, the measurement uncertainty of the workpiece with a diameter 1.5 mm and length 5.8 mm is evaluated to be 0.095 μm which can meet the uncertainty target of 0.1 μm. Considering the uncertainty of θx and θz which are the alignment around X-axis and Z-axis respectively changing with workpiece dimension changing, relevant uncertainties are carried out. As a result, there is no limitation with respect to workpiece diameter theoretically If the alignment can reach θz = θx = ±0.1° without considering the measurable range of the machine.
- 6 February 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (9) , 11973-11988
Multi-objective Optimization of Non-circular Gear Through Orthogonal Array and Fuzzy Comprehensive Evaluation Method in WEDM
- 6 February 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (9) , 11973-11988
Multi-objective Optimization of Non-circular Gear Through Orthogonal Array and Fuzzy Comprehensive Evaluation Method in WEDM
- Open Access
Automatic Current-Constrained Double Loop ADRC for Electro-Hydrostatic Actuator Based on Singular Perturbation Theory
For an electro-hydrostatic actuator (EHA), the position, speed, and current cascade three-loop control architecture are dominant in existing active disturbance rejection control (ADRC). However, this architecture suffers from many problems, such as severe noise sensitivity of the extended state observer (ESO), excessive complexity of control structure, and too many tuned parameters, which makes the controller not easy to implement in practice. Aiming at the above drawbacks, a novel cascade double-loop ADRC strategy that is automatic current-constrained is proposed, which makes the whole ADRC architecture simplified to the position and the integrated speed–current double-loop architecture. Firstly, for the position control loop, the singular perturbation theory is used to reasonably reduce the order of the model for the position subsystem of EHA. A reduced order ADRC controller (ROADRC) is synthesized, which not only effectively reduces the noise sensitivity of ESO, but also circumvents use of the actuation acceleration information in the controller design process. Secondly, the integrated speed–current ADRC controller is designed by taking the speed and current subsystems of EHA into synthesis, which avoids the problem of excessive current loop bandwidth in conventional three-loop control architecture, and the number of tuned parameters is significantly reduced. Additionally, an uncomplicated and effective automatic current-constrained ADRC controller (CACADRC) is designed to solve the problem in the integrated speed–current ADRC that the current cannot be automatically constrained. Finally, by comparing the three-loop PI controller with the traditional three-loop ADRC, a detailed simulation analysis is carried out to verify the effectiveness and merits of the proposed controller. The simulation results show that the proposed controller not only inherits the advantages of high precision and strong disturbance rejection performance of the conventional ADRC, but can also efficiently decrease the noise sensitivity of ESO and effectively achieve the current-constrained control.
Open AccessAutomatic Current-Constrained Double Loop ADRC for Electro-Hydrostatic Actuator Based on Singular Perturbation Theory
For an electro-hydrostatic actuator (EHA), the position, speed, and current cascade three-loop control architecture are dominant in existing active disturbance rejection control (ADRC). However, this architecture suffers from many problems, such as severe noise sensitivity of the extended state observer (ESO), excessive complexity of control structure, and too many tuned parameters, which makes the controller not easy to implement in practice. Aiming at the above drawbacks, a novel cascade double-loop ADRC strategy that is automatic current-constrained is proposed, which makes the whole ADRC architecture simplified to the position and the integrated speed–current double-loop architecture. Firstly, for the position control loop, the singular perturbation theory is used to reasonably reduce the order of the model for the position subsystem of EHA. A reduced order ADRC controller (ROADRC) is synthesized, which not only effectively reduces the noise sensitivity of ESO, but also circumvents use of the actuation acceleration information in the controller design process. Secondly, the integrated speed–current ADRC controller is designed by taking the speed and current subsystems of EHA into synthesis, which avoids the problem of excessive current loop bandwidth in conventional three-loop control architecture, and the number of tuned parameters is significantly reduced. Additionally, an uncomplicated and effective automatic current-constrained ADRC controller (CACADRC) is designed to solve the problem in the integrated speed–current ADRC that the current cannot be automatically constrained. Finally, by comparing the three-loop PI controller with the traditional three-loop ADRC, a detailed simulation analysis is carried out to verify the effectiveness and merits of the proposed controller. The simulation results show that the proposed controller not only inherits the advantages of high precision and strong disturbance rejection performance of the conventional ADRC, but can also efficiently decrease the noise sensitivity of ESO and effectively achieve the current-constrained control.
- Open Access
- 14 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (24) , 12858
Research on the Tooth Surface Integrity of Non-Circular Gear WEDM Based on HPSO Optimization SVR
Non-circular gears have the characteristics of gear ratio accuracy, good dynamic performance, and wide application prospects but are difficult to manufacture. Wire electrical discharge machining (WEDM) can process almost all kinds of non-circular gear. In order to solve the problem that the process parameters are mainly adjusted using the operator’s experience and to improve the surface quality of non-circular gears machined using WEDM, this research took Pascal gears processed with a fast-walking WEDM machine as the object, conducted orthogonal tests, and used hybrid particle swarm optimization (HPSO) to optimize support vector regression (SVR) with different kernel functions, to predict various surface integrity indicators. The results showed that the rbf kernel function had a better performance in the prediction model of surface integrity indicators, which can provide a reference for the parameter selection of non-circular gear machining using WEDM. The final predicted results were R2 = 0.9978, MAPE = 0.4534 for surface roughness, R2 = 0.9483, MAPE = 3.1673 for surface residual stress, and R2 = 0.9786, MAPE = 0.4779 for surface microhardness.
- 14 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (24) , 12858
Open AccessResearch on the Tooth Surface Integrity of Non-Circular Gear WEDM Based on HPSO Optimization SVR
Non-circular gears have the characteristics of gear ratio accuracy, good dynamic performance, and wide application prospects but are difficult to manufacture. Wire electrical discharge machining (WEDM) can process almost all kinds of non-circular gear. In order to solve the problem that the process parameters are mainly adjusted using the operator’s experience and to improve the surface quality of non-circular gears machined using WEDM, this research took Pascal gears processed with a fast-walking WEDM machine as the object, conducted orthogonal tests, and used hybrid particle swarm optimization (HPSO) to optimize support vector regression (SVR) with different kernel functions, to predict various surface integrity indicators. The results showed that the rbf kernel function had a better performance in the prediction model of surface integrity indicators, which can provide a reference for the parameter selection of non-circular gear machining using WEDM. The final predicted results were R2 = 0.9978, MAPE = 0.4534 for surface roughness, R2 = 0.9483, MAPE = 3.1673 for surface residual stress, and R2 = 0.9786, MAPE = 0.4779 for surface microhardness.