Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jie Huang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Paired Fluid‐Mediated Bidirectional SMA Actuators for Soft Robots

    by Qingqian Cai, Lingrui Shen, Jie Huang, Yuan‐Fang Zhang, Ye Chen, Changchun Wu, Senyuan Lin, Yunquan Li

    Shape memory alloys (SMAs) are promising materials for soft robotic actuators due to their high energy density and compact form. However, conventional SMA‐based systems are inherently limited in achieving effective bidirectional motion. To address this challenge, Paired Fluid‐Mediated Bidirectional Shape Memory Alloy (Paired‐FBSMA) actuators are proposed, which couple thermally driven SMA springs with fluid‐mediated force transmission. Each FBSMA unit consists of a fluid‐filled bellows actuated by two parallel SMA springs, and two such units are interconnected to enable reciprocal fluid exchange and active bidirectional actuation. This design supports modular and flexible integration into robotic systems while enhancing actuation efficiency. By tuning the water‐air ratio inside the bellows, both output force and displacement stroke can be effectively modulated, with higher water content yielding greater recovery forces. Extensive experimental validation demonstrates that Paired‐FBSMA actuators outperform conventional SMA‐only and SMA‐bellows configurations in both stroke and force generation. The actuators are implemented in a soft crawling robot and a two‐degree‐of‐freedom joint mechanism, achieving stable crawling locomotion and repeatable reciprocating motion. These results highlight the versatility, tunability, and strong potential of the Paired‐FBSMA actuators for integration into next‐generation soft robotic systems requiring compact, distributed, and high‐output actuation.

  • Autologous Variable Stiffness Soft Finger Based on Cross-Layer Jamming for Multimode Grasping

    by Jie Huang, Ling-Jie Gai, Lingrui Shen, Qingqian Cai, Yunquan Li, Yingtian Li, Xuemin Gao, Xiaofeng Zong

    Layer jamming variable stiffness technologies have been widely explored to enhance the load-bearing capacity of soft robotic fingers. However, these technologies typically require layer-jamming units to be attached to soft actuators as additional components, complicating structural design and limiting flexible multiconfiguration actuation. To address these problems, we propose an autologous variable stiffness soft finger (AVSSF) that integrates the cross-layer jamming joints (CLJJs) as both the variable stiffness unit and the finger itself, actuated by tendons. This design ensures a simple and compact structure while offering a wide range of stiffness adjustment. Additionally, by coordinating tendon actuation with the control of the CLJJ's jammed and unjammed states, the AVSSF achieves multiple configurations, providing flexibility in operation. Experimental results demonstrates that the stiffness of the AVSSF increased by a factor of 79.5 after modulation. We develop a two-finger gripper based on this design, capable of executing four distinct grasping modes: power grasp, adaptive pinch, expansion grasp, and hook. This gripper demonstrates adaptability to various objects and environments, highlighting its potential for diverse applications. In summary, this work offers insights into the advancement of autologous variable stiffness technologies and the development of multimodal grasping capabilities.


  • A Soft Finger With Tensile Variable Stiffness Based on the Cross-Sliding Jamming Mechanism

    by Ling-Jie Gai, Jie Huang, Yuanyuan Zhang, Xiaofeng Zong, Huafeng Ding

    Variable stiffness mechanisms provide an effective means to enhance the load-bearing capacity of soft fingers, but due to the lack of stretchability, their assembly position is often limited to the lower surface of soft bending actuators. Here, a Cross-Sliding jamming mechanism with tensile properties is developed to overcome this restriction. The mechanism is integrated on the upper surface of a soft actuator and can be passively stretched as the actuator bends. By changing the assembly position, the defect of rigidity contact between the conventional variable stiffness fingers and the object is solved, and the disturbance caused by the variable stiffness structure to the contact surface during the jamming process is eliminated. Furthermore, a multi-fingered gripper is assembled based on the variable stiffness soft fingers, demonstrating its effective grasping capability and stability by bending, stiffness, vibration experiments and so on. The reported study provides novel design and application insights for stiffness modulation in soft robots.


  • Stiffness-Tunable Soft Bellows Actuators by Cross-Fiber Jamming Effect for Robust Grasping

    by Ling-Jie Gai, Jie Huang, Xiaofeng Zong

    Soft actuators typically exhibit low stiffness and low load-bearing properties due to the intrinsic limitations of soft materials. Stiffness modulation is an effective means to improve the performance of soft actuators. However, most stiffness-tunable mechanisms are nonstretchable, and have difficulty in independently adjusting the tensile stiffness of soft elongation actuators. Here, a universal cross-fiber jamming mechanism with both elongation and bending stiffness-tunable capability is proposed for soft bellows actuators. It is composed of two semicircular symmetrical fiber bundles in an up-and-down crossed arrangement, and can follow the tensile state of the soft bellows actuator through the passive staggered motion of the layered fiber bundles. Furthermore, a soft gripper with wide grasping range and sufficient grasping stability is also developed by applying soft bellows actuators with cross-fiber jamming mechanisms. Experiments are conducted to show the related performance of the proposed cross-fiber jamming mechanism. The results show that it has fast antiimpact damping response, strong shaping ability and adjustable stiffness. Such efficient performance will promote the ability of grasping robots, and is expected to be used in daily life and industry.


  • Enhancing the Tensile-Shaping Stability of Soft Elongation Actuators for Grasping Applications

    by Ling-Jie Gai, Xiaofeng Zong, Jie Huang

    Soft elongation actuators are widely applied in soft robotic grippers, providing a promising solution to adjust the grasping range. However, there are some limitations in keeping their tensile shaping stability under high payloads. This work presents a universal variable stiffness mechanism called Cross-Fibre to reduce the deformation and improve the load-bearing capacity of soft elongation actuators. The proposed mechanism is composed of two symmetrical fibre loops in an up-and-down crossed arrangement around the soft elongation actuator. The fibre media on both sides can be stretched compliantly with the actuator, and thus achieve global variable stiffness. In addition, based on the soft elongation actuator with variable stiffness, this work also develops a novel soft gripper prototype for automatically adjusting the grasping range and enhancing grasping applications. Experiments demonstrate that the soft elongation actuator with Cross-Fibre effect has strong tensile-shaping ability, and the soft gripper can stably grasp objects weighting more than 1700 g. Such efficient performance will promote various applications in daily life and industry.


  • High prevalence and low spontaneous eradication rate of Helicobacter pylori infection among schoolchildren aged 7–12 years

    by Ying Zhou, Ziqing Ye, Jie Huang, Ying Huang, Weili Yan, Yi Zhang

    Aim: Helicobacter pylori infections mainly occur during childhood and may cause chronic diseases and persist for life unless they are treated. The aim of this study was to identify the prevalence and infection status of H. pylori infection among schoolchildren.Methods: We conducted a cross‐sectional study of 867 children (52% male) aged 7–12 years in a primary school in the Minhang District of Shanghai, China, in 2014, and a one‐year follow‐up study of 352 subjects. The 13C‐urea breath test was used to identify the H. pylori infection at baseline and one year later. A parental questionnaire provided information regarding the children's socioeconomic status and household environment.Results: The overall prevalence of the H. pylori infection was 24.1% (209/867), with a 95% confidence interval of 21.3% to 27.0%. The one‐year follow‐up study of 352 subjects found that 33.5% were positive for the infection at baseline and 66.5% were negative. We found that 27.1% of the positive cases recovered and 8.9% of the negative cases acquired the infection during the year. The spontaneous eradication rate was only 2.9% over the one‐year period.Conclusion: The prevalence of the H. pylori infection among Chinese schoolchildren aged 7–12 was high and spontaneous eradication was low.