Honggang Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Honggang Dong has a total of 155 co-authors. Here are the top co-authors by number of shared publications:
Peng Li
21 shared publicationsJiachen Li
9 shared publicationsJilong Wang
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, PR China
9 shared publicationsLiangliang Zhang
School of Materials Science and Engineering, Dalian University of Technology, Dalian, China
9 shared publicationsZhiwei Qin
9 shared publicationsFushuai Jin
School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, PR China
7 shared publications
Latest Publications
- 2 November 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (21) , 10683-10696
An interfacial nanostructure-specific tailoring strategy to address the strength and ductility trade-off in inertia friction welded dissimilar superalloys
Inertia friction welding (IFW) of dissimilar Ni-based superalloys offers great promise for aero-engine manufacturing, yet the persistent strength–ductility trade-off in welded joints restricts their reliable service under extreme conditions.
- 2 November 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (21) , 10683-10696
An interfacial nanostructure-specific tailoring strategy to address the strength and ductility trade-off in inertia friction welded dissimilar superalloys
Inertia friction welding (IFW) of dissimilar Ni-based superalloys offers great promise for aero-engine manufacturing, yet the persistent strength–ductility trade-off in welded joints restricts their reliable service under extreme conditions.
- Open Access
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Non-monotonic strength in WAAM Al-Zn-Mg-Cu alloy under transient thermal cycling: Microstructural origins and role of arc energy
Wire arc additive manufacturing (WAAM) of high-strength Al-Zn-Mg-Cu alloys involves complex transient thermal cycles that alter the balance among strengthening mechanisms, thereby affecting mechanical properties. Herein, Al-Zn-Mg-Cu thin walls were fabricated at arc energies of 76.8, 89.6, and 107.5 J mm-1 to investigate how thermal input influences the competition among strengthening mechanisms. The deposits consisted of an α-Al matrix with η phase precipitates. The tensile response was non-monotonic: the wall fabricated at 89.6 J mm-1 exhibited the highest yield strength in both the horizontal and vertical directions despite having the largest average grain size (131.3 μm). The corresponding ultimate tensile strengths and elongations in the horizontal and vertical directions were 251 and 208 MPa and 3.6% and 2.0%, respectively. With increasing arc energy, cellular/dendritic structures and η phase precipitates coarsened, while the local solute concentration in the α-Al matrix decreased. The wall fabricated at 89.6 J mm-1 exhibited the highest KAM and contained dispersed intragranular equilibrium η precipitates. An incoherent η/α-Al interface and a coherent η/η boundary inside the grain-boundary η precipitate were also identified in this wall. These observations suggest that enhanced dislocation strengthening and particle strengthening likely compensate for the reduced grain-boundary and solid-solution strengthening contributions. Among the investigated conditions, 89.6 J mm-1 provided a favorable combination of strength and ductility.
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNon-monotonic strength in WAAM Al-Zn-Mg-Cu alloy under transient thermal cycling: Microstructural origins and role of arc energy
Wire arc additive manufacturing (WAAM) of high-strength Al-Zn-Mg-Cu alloys involves complex transient thermal cycles that alter the balance among strengthening mechanisms, thereby affecting mechanical properties. Herein, Al-Zn-Mg-Cu thin walls were fabricated at arc energies of 76.8, 89.6, and 107.5 J mm-1 to investigate how thermal input influences the competition among strengthening mechanisms. The deposits consisted of an α-Al matrix with η phase precipitates. The tensile response was non-monotonic: the wall fabricated at 89.6 J mm-1 exhibited the highest yield strength in both the horizontal and vertical directions despite having the largest average grain size (131.3 μm). The corresponding ultimate tensile strengths and elongations in the horizontal and vertical directions were 251 and 208 MPa and 3.6% and 2.0%, respectively. With increasing arc energy, cellular/dendritic structures and η phase precipitates coarsened, while the local solute concentration in the α-Al matrix decreased. The wall fabricated at 89.6 J mm-1 exhibited the highest KAM and contained dispersed intragranular equilibrium η precipitates. An incoherent η/α-Al interface and a coherent η/η boundary inside the grain-boundary η precipitate were also identified in this wall. These observations suggest that enhanced dislocation strengthening and particle strengthening likely compensate for the reduced grain-boundary and solid-solution strengthening contributions. Among the investigated conditions, 89.6 J mm-1 provided a favorable combination of strength and ductility.
- Open Access
- 2 October 2026
- Published by IOP Publishing in International Journal of Extreme Manufacturing
- Vol. 9 (1) , 015010
Lattice reconstruction and dislocation recapture enhance the fracture resistance of η-Fe 2 Al 5 -bearing interfaces in dissimilar Al/steel joints
The inherent brittleness of interfacial Al-rich intermetallic compounds (IMCs) remains a major obstacle to reliable Fe-Al-based lightweight structural joints, as welding-induced residual-stress localization readily triggers crack initiation within the IMC-bearing region. Here, a two-step strategy integrating lattice reconstruction with dislocation recapture is proposed to improve the room-temperature fracture resistance of η-Fe 2 Al 5 in dissimilar Al/steel joints. Low-temperature annealing promotes rapid reconstruction of the strained η-Fe 2 Al 5 lattice and relieves long-range residual stress, while subsequent water quenching facilitates the recapture of dispersed isolated dislocations. The treated joints achieve a tensile strength of ~258.6 MPa, corresponding to an ~80.3% increase over the as-processed state, together with a ~70% increase in the fracture toughness of the η-Fe 2 Al 5 -bearing layer. In situ X-ray diffraction and first-principles calculations reveal that localized compressive strain accelerates the reverse eutectoid transformation, through which β 0 -associated transformation strain provides an additional driving force for dislocation-network decoupling and stress relief of the η-Fe 2 Al 5 layer. The retained coherent η-Fe 2 Al 5 /β 0 interface and the recaptured isolated dislocations further promote local strain accommodation in η-Fe 2 Al 5 , while crack deflection, blunting, and bridging dissipate fracture energy, as supported by molecular dynamics simulations. These results suggest a potential strategy for improving fracture-limited IMC-bearing interfaces in dissimilar-metal joints through coordinated regulation of residual stress and dislocation functionality.
- 2 October 2026
- Published by IOP Publishing in International Journal of Extreme Manufacturing
- Vol. 9 (1) , 015010
Open AccessLattice reconstruction and dislocation recapture enhance the fracture resistance of η-Fe 2 Al 5 -bearing interfaces in dissimilar Al/steel joints
The inherent brittleness of interfacial Al-rich intermetallic compounds (IMCs) remains a major obstacle to reliable Fe-Al-based lightweight structural joints, as welding-induced residual-stress localization readily triggers crack initiation within the IMC-bearing region. Here, a two-step strategy integrating lattice reconstruction with dislocation recapture is proposed to improve the room-temperature fracture resistance of η-Fe 2 Al 5 in dissimilar Al/steel joints. Low-temperature annealing promotes rapid reconstruction of the strained η-Fe 2 Al 5 lattice and relieves long-range residual stress, while subsequent water quenching facilitates the recapture of dispersed isolated dislocations. The treated joints achieve a tensile strength of ~258.6 MPa, corresponding to an ~80.3% increase over the as-processed state, together with a ~70% increase in the fracture toughness of the η-Fe 2 Al 5 -bearing layer. In situ X-ray diffraction and first-principles calculations reveal that localized compressive strain accelerates the reverse eutectoid transformation, through which β 0 -associated transformation strain provides an additional driving force for dislocation-network decoupling and stress relief of the η-Fe 2 Al 5 layer. The retained coherent η-Fe 2 Al 5 /β 0 interface and the recaptured isolated dislocations further promote local strain accommodation in η-Fe 2 Al 5 , while crack deflection, blunting, and bridging dissipate fracture energy, as supported by molecular dynamics simulations. These results suggest a potential strategy for improving fracture-limited IMC-bearing interfaces in dissimilar-metal joints through coordinated regulation of residual stress and dislocation functionality.
- 11 July 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 281, 263-273
Dual-gradient structures of high-performance diffusion-bonded Ni-based superalloys enabled by a multicomponent alloy interlayer
- 11 July 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 281, 263-273
Dual-gradient structures of high-performance diffusion-bonded Ni-based superalloys enabled by a multicomponent alloy interlayer
- 12 May 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 278, 47-60
In-situ CO2-induced synthesis of T2-Al2MgC2 phase enabled high-performance wire arc additive-manufactured AZ91D Mg-based alloy
- 12 May 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 278, 47-60
In-situ CO2-induced synthesis of T2-Al2MgC2 phase enabled high-performance wire arc additive-manufactured AZ91D Mg-based alloy
- 8 April 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (12) , 5974-5985
In situ synthesis of dispersed boride-induced high-performance brazed DD5 superalloy via the formation of a novel sandwich-structured interlayer
A novel sandwich-structured interlayer enhanced the shear strength of the brazed superalloy by 74.4% through converting trapped boron atoms into dispersed borides, thereby suppressing brittle phases.
- 8 April 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (12) , 5974-5985
In situ synthesis of dispersed boride-induced high-performance brazed DD5 superalloy via the formation of a novel sandwich-structured interlayer
A novel sandwich-structured interlayer enhanced the shear strength of the brazed superalloy by 74.4% through converting trapped boron atoms into dispersed borides, thereby suppressing brittle phases.
- Open Access
- 23 March 2026
- Published by Elsevier in SSRN Electronic Journal
Co-doped amorphous filler metals enabled high-strength brazed DZ125 superalloys
Pursuing high-performance fillers that can satisfy the precision joining requirements of advanced directionally superalloys in high-end fields has become paramount. Herein, Co-doped Ni-Co-Si-B amorphous brazed fillers were designed to promote the formation of dispersed borides and the refinement of γ′ phases in the brazed seam. The phase distribution of the brazed seam transformed from coarse petal-like γ′ phase to the dispersed borides and cubic γ′ phase with the increase of Co content. Microstructural characterizations indicated that Co doping inhibited B atom diffusion, reduced the width of the diffusion-affected zone, and improved the microhardness (6.1 GPa) and elastic modulus (228.2 GPa). The DZ125 superalloys were successfully vacuum brazed to achieve a shear strength of 815 MPa. Since the atomic radius of Co was slightly larger than that of Ni and occupied its lattice sites, the solid solution strengthening effect was enhanced to improve the strength of the brazed joint. Meanwhile, the γ′ phase was further refined and dispersed to induce a dispersion strengthening effect. The Ni53.83Co23.07Si7.69B15.38 brazed filler metal accelerated the refinement of grains at the brazed seam (average grain size of 4.3 μm) with high-angle grain boundaries accounting for 94.2%, which produced a fine-grain strengthening effect to hinder crack propagation. The fracture mode was typically a quasi-cleavage fracture instead of a cleavage fracture, exhibiting obvious plastic characteristics. This work provided an effective design strategy of amorphous brazed fillers and a theoretical foundation for the broader application of DZ125 superalloy in high-temperature aerospace components.
- 23 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCo-doped amorphous filler metals enabled high-strength brazed DZ125 superalloys
Pursuing high-performance fillers that can satisfy the precision joining requirements of advanced directionally superalloys in high-end fields has become paramount. Herein, Co-doped Ni-Co-Si-B amorphous brazed fillers were designed to promote the formation of dispersed borides and the refinement of γ′ phases in the brazed seam. The phase distribution of the brazed seam transformed from coarse petal-like γ′ phase to the dispersed borides and cubic γ′ phase with the increase of Co content. Microstructural characterizations indicated that Co doping inhibited B atom diffusion, reduced the width of the diffusion-affected zone, and improved the microhardness (6.1 GPa) and elastic modulus (228.2 GPa). The DZ125 superalloys were successfully vacuum brazed to achieve a shear strength of 815 MPa. Since the atomic radius of Co was slightly larger than that of Ni and occupied its lattice sites, the solid solution strengthening effect was enhanced to improve the strength of the brazed joint. Meanwhile, the γ′ phase was further refined and dispersed to induce a dispersion strengthening effect. The Ni53.83Co23.07Si7.69B15.38 brazed filler metal accelerated the refinement of grains at the brazed seam (average grain size of 4.3 μm) with high-angle grain boundaries accounting for 94.2%, which produced a fine-grain strengthening effect to hinder crack propagation. The fracture mode was typically a quasi-cleavage fracture instead of a cleavage fracture, exhibiting obvious plastic characteristics. This work provided an effective design strategy of amorphous brazed fillers and a theoretical foundation for the broader application of DZ125 superalloy in high-temperature aerospace components.
- Open Access
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (6) , 3057-3068
A high-entropy gradient filler metal enables high-strength joints of Ti 2 AlNb and GH4169 alloys
Vacuum brazing with an innovative filler alloy is critical for manufacturing high-precision aerospace components requiring exceptional comprehensive performance, yet achieving superior strength in Ti 2 AlNb/GH4169 brazed joints remains challenging.
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (6) , 3057-3068
Open AccessA high-entropy gradient filler metal enables high-strength joints of Ti 2 AlNb and GH4169 alloys
Vacuum brazing with an innovative filler alloy is critical for manufacturing high-precision aerospace components requiring exceptional comprehensive performance, yet achieving superior strength in Ti 2 AlNb/GH4169 brazed joints remains challenging.