Pingxin Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pingxin Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoting Rui
National Key Laboratory of Complex Multibody System Dynamics Nanjing University of Science and Technology Nanjing China
5 shared publications Guoping Wang
Institute of Launch Dynamics, Nanjing University of Science and Technology, Nanjing, China
4 shared publications- Guoping Wang
Nanjing University of Science and Technology
4 shared publications Jianshu Zhang
Institute of Launch Dynamics, Nanjing University of Science and Technology, Nanjing, China
4 shared publications- Min Jiang
Nanjing University of Science and Technology
3 shared publications Hailong Yu
Nanjing University of Science and Technology
2 shared publications
Latest Publications
- Open Access
Study on the Influence of Heat Input on Microstructure and Properties of Q420C Steel Welded Joints
The occurrence of the welding heat-affected zone in Q420C steel may lead to a reduction in the toughness of the welded joint and disruption of high strength-toughness combination of Q420C. This study investigates the microstructure and mechanical properties of Q420C steel welded joints under three heat in-puts of 25 kJ/cm, 100 kJ/cm, 200 kJ/cm, and 300 kJ/cm, with high-strength matching adopted for the welded joints, Charpy impact tests at 0 °C, −20 °C, and −40 °C were conducted on the weld metal, fusion line(FL), and heat-affected zone (HAZ). The weld metal maintains high impact toughness across all tested temperatures. However, increasing the heat input leads to coarsening of the microstructure in the overheated zone of the HAZ, accompanied by the formation of ferrite. At a heat input of 300 kJ/cm, significant amounts of coarse intergranular ferrite and intragranular blocky ferrite develop in the overheated zone. These microstructural changes result in a marked reduction in the impact toughness of both the fusion zone and HAZ, and the fracture mode shifts from ductile to cleavage fracture. To ensure adequate impact toughness of Q420C welded joints, the welding heat input should be kept below 200 kJ/cm.
Open AccessStudy on the Influence of Heat Input on Microstructure and Properties of Q420C Steel Welded Joints
The occurrence of the welding heat-affected zone in Q420C steel may lead to a reduction in the toughness of the welded joint and disruption of high strength-toughness combination of Q420C. This study investigates the microstructure and mechanical properties of Q420C steel welded joints under three heat in-puts of 25 kJ/cm, 100 kJ/cm, 200 kJ/cm, and 300 kJ/cm, with high-strength matching adopted for the welded joints, Charpy impact tests at 0 °C, −20 °C, and −40 °C were conducted on the weld metal, fusion line(FL), and heat-affected zone (HAZ). The weld metal maintains high impact toughness across all tested temperatures. However, increasing the heat input leads to coarsening of the microstructure in the overheated zone of the HAZ, accompanied by the formation of ferrite. At a heat input of 300 kJ/cm, significant amounts of coarse intergranular ferrite and intragranular blocky ferrite develop in the overheated zone. These microstructural changes result in a marked reduction in the impact toughness of both the fusion zone and HAZ, and the fracture mode shifts from ductile to cleavage fracture. To ensure adequate impact toughness of Q420C welded joints, the welding heat input should be kept below 200 kJ/cm.
- 17 March 2025
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 113 (13) , 16461-16476
A novel recursive method for dynamic modeling of planar rigid multibody systems with revolute clearance joints
- 17 March 2025
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 113 (13) , 16461-16476
A novel recursive method for dynamic modeling of planar rigid multibody systems with revolute clearance joints
- 24 February 2025
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (7-8) , 1838-1851
Non-parametric modeling of magnetorheological damper based on MEA-BP neural network
The process of parametric modeling of magnetorheological (MR) damper presents difficulties such as numerous parameters, complicated and time-consuming identification procedures, and difficulty in establishing the inverse model. In order to solve these problems, this paper adopts the mind evolution algorithm backpropagation (MEA-BP) neural network to successfully establish the forward model and the inverse model for prediction of electric current. These models can accurately capture the nonlinear hysteresis characteristics of MR damper. First, the mechanical properties of the MR damper were tested, and then the BP neural network structure of the forward and inverse models was determined according to its working principle. Aiming at the problems of traditional BP neural network which is easy to mature prematurely and converge slowly, the initial weights and thresholds of BP neural network were optimized by using MEA. Utilizing the Mechanical properties test results of the MR damper, the MEA-BP neural network was used to identify the forward and inverse non-parametric models of the MR damper. Compared with the traditional BP neural network model, the forward model and inverse model of the MR damper, based on the MEA-BP neural network, showed an improvement in prediction accuracy by 33.96% and 26.32%, respectively. The forward model based on the MEA-BP neural network demonstrated a 16.67% improvement in accuracy compared to the genetic algorithm (GA) BP neural network. The non-parametric model, developed using the MEA-BP neural network, more accurately captures the dynamic behavior of the MR damper. This advancement provides a robust foundation for research into the dynamics and semi-active control of MR adaptive damping systems.
- 24 February 2025
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (7-8) , 1838-1851
Non-parametric modeling of magnetorheological damper based on MEA-BP neural network
The process of parametric modeling of magnetorheological (MR) damper presents difficulties such as numerous parameters, complicated and time-consuming identification procedures, and difficulty in establishing the inverse model. In order to solve these problems, this paper adopts the mind evolution algorithm backpropagation (MEA-BP) neural network to successfully establish the forward model and the inverse model for prediction of electric current. These models can accurately capture the nonlinear hysteresis characteristics of MR damper. First, the mechanical properties of the MR damper were tested, and then the BP neural network structure of the forward and inverse models was determined according to its working principle. Aiming at the problems of traditional BP neural network which is easy to mature prematurely and converge slowly, the initial weights and thresholds of BP neural network were optimized by using MEA. Utilizing the Mechanical properties test results of the MR damper, the MEA-BP neural network was used to identify the forward and inverse non-parametric models of the MR damper. Compared with the traditional BP neural network model, the forward model and inverse model of the MR damper, based on the MEA-BP neural network, showed an improvement in prediction accuracy by 33.96% and 26.32%, respectively. The forward model based on the MEA-BP neural network demonstrated a 16.67% improvement in accuracy compared to the genetic algorithm (GA) BP neural network. The non-parametric model, developed using the MEA-BP neural network, more accurately captures the dynamic behavior of the MR damper. This advancement provides a robust foundation for research into the dynamics and semi-active control of MR adaptive damping systems.
- 12 February 2025
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 13 (2) , 1-14
Complex Modal Analysis of a Resilient Supported Conveyor Belt: Enhancement of Numerical Stability by Reduced Complex Transfer Matrix Method
- 12 February 2025
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 13 (2) , 1-14
Complex Modal Analysis of a Resilient Supported Conveyor Belt: Enhancement of Numerical Stability by Reduced Complex Transfer Matrix Method
- 2 February 2025
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (11-12) , 2795-2805
Transversal vibration of a multi-span axially moving beam with multiple elastic supports
Using the transfer matrix method for multibody systems (MSTMM), this paper presents a dynamical model of a multi-span axially moving system with multiple elastic supports under different boundary conditions. The complex transfer matrices of an axially moving beam and a spring-damping supporting element are derived. According to the system topology, the overall transfer equation is acquired for vibration characteristic analysis. However, when dealing with multi-span systems that involve a large number of components, numerical instability may arise due to the instability of the corresponding boundary value problems. To address this issue, the reduced complex transfer matrix method (RCTMM) is developed. The state vector is artificially partitioned corresponding to the boundary condition of the system input. Numerical simulation results show that the developed method has the same computational accuracy as the MSTMM. More importantly, the RCTMM exhibits superior numerical stability, as indicated by the condition numbers of the system transfer matrix. It will provide an efficient tool for the design of mechanical multi-span axially moving systems.
- 2 February 2025
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (11-12) , 2795-2805
Transversal vibration of a multi-span axially moving beam with multiple elastic supports
Using the transfer matrix method for multibody systems (MSTMM), this paper presents a dynamical model of a multi-span axially moving system with multiple elastic supports under different boundary conditions. The complex transfer matrices of an axially moving beam and a spring-damping supporting element are derived. According to the system topology, the overall transfer equation is acquired for vibration characteristic analysis. However, when dealing with multi-span systems that involve a large number of components, numerical instability may arise due to the instability of the corresponding boundary value problems. To address this issue, the reduced complex transfer matrix method (RCTMM) is developed. The state vector is artificially partitioned corresponding to the boundary condition of the system input. Numerical simulation results show that the developed method has the same computational accuracy as the MSTMM. More importantly, the RCTMM exhibits superior numerical stability, as indicated by the condition numbers of the system transfer matrix. It will provide an efficient tool for the design of mechanical multi-span axially moving systems.
- Open Access
- 28 October 2024
- Published by Springer Nature in Research Square
Three-dimensional nonlinear tooth meshing modeling and analysis for preloaded tracked vehicles.
The single-pin track system is widely used in light-tracked vehicles due to its simple structure and high reliability. This paper aims to establish a nonlinear three-dimensional tooth engagement search process to simulate the meshing process between the single-pin track shoe and the sprocket, thereby improving the accuracy of multibody system dynamics simulations. Based on the actual geometric structure, the contact surfaces between the sprocket teeth and the track pin are discretized, and a body-fixed coordinate system is introduced for each contact surface to facilitate the geometric contact criteria and contact force calculation. Through simulation, the effect of pre-tension on tooth engagement is analyzed, revealing the dynamics of the track chain as a function of pre-tension variation. Simulation results, validated by commercial software and experimental tests, indicate that the proposed 3D meshing model can effectively simulate the impact of high-frequency excitations on tracked vehicles. Furthermore, the study provides suggestions for optimizing the design of the track shoe and sprocket to improve the service life of the meshing system.
- 28 October 2024
- Published by Springer Nature in Research Square
Open AccessThree-dimensional nonlinear tooth meshing modeling and analysis for preloaded tracked vehicles.
The single-pin track system is widely used in light-tracked vehicles due to its simple structure and high reliability. This paper aims to establish a nonlinear three-dimensional tooth engagement search process to simulate the meshing process between the single-pin track shoe and the sprocket, thereby improving the accuracy of multibody system dynamics simulations. Based on the actual geometric structure, the contact surfaces between the sprocket teeth and the track pin are discretized, and a body-fixed coordinate system is introduced for each contact surface to facilitate the geometric contact criteria and contact force calculation. Through simulation, the effect of pre-tension on tooth engagement is analyzed, revealing the dynamics of the track chain as a function of pre-tension variation. Simulation results, validated by commercial software and experimental tests, indicate that the proposed 3D meshing model can effectively simulate the impact of high-frequency excitations on tracked vehicles. Furthermore, the study provides suggestions for optimizing the design of the track shoe and sprocket to improve the service life of the meshing system.
- 18 June 2024
- Published by Springer Nature
- p. 4249-4266
Fast Calculation of Vibration Characteristics for Tracked Vehicle
- 18 June 2024
- Published by Springer Nature
- p. 4249-4266
Fast Calculation of Vibration Characteristics for Tracked Vehicle
- 18 June 2024
- Published by Springer Nature
- p. 4035-4047
Dynamic Performance Analysis of Track Rubber Bushing Considering Thermal Stress Coupling
- 18 June 2024
- Published by Springer Nature
- p. 4035-4047
Dynamic Performance Analysis of Track Rubber Bushing Considering Thermal Stress Coupling
- Open Access
- 13 December 2022
- Published by Wiley in International Journal of Mechanical System Dynamics
- Vol. 3 (2) , 146-161
Generation mechanism and control of high‐frequency vibration for tracked vehicles
A crawler system provides much larger ground contact, leading to excellent terrain adaptability. Due to its structural characteristics, high‐frequency vibration proportional to the vehicle speed is generated during the driving process. This is a result of the polygon and rolling effects between the track and the wheels. A field test of a tracked vehicle is performed to monitor movement signals of the chassis and a rocker arm. Their corresponding power spectral density distributions confirm the correctness of the frequency‐calculation equation. Then, a novel elastic track tensioning device with a damper is designed as a cushion between the idler and the chassis. Depending on its geometry, the equivalent damping coefficient for a dynamic model is evaluated. Subsequently, the damping is altered in response to different operating conditions by a hybrid damping fuzzy semiactive control system. The controller accounts for both chassis and track vibration. Based on the transfer matrix method for multibody systems, a dynamical model of the track system is developed. Control performances are evaluated using two numerical simulations of obstacle crossing and off‐road driving operations. Results indicate that the proposed semiactive tensioner is substantially better than the conventional one. This paper provides a novel feasible scheme for vibration reduction of tracked vehicles.
- 13 December 2022
- Published by Wiley in International Journal of Mechanical System Dynamics
- Vol. 3 (2) , 146-161
Open AccessGeneration mechanism and control of high‐frequency vibration for tracked vehicles
A crawler system provides much larger ground contact, leading to excellent terrain adaptability. Due to its structural characteristics, high‐frequency vibration proportional to the vehicle speed is generated during the driving process. This is a result of the polygon and rolling effects between the track and the wheels. A field test of a tracked vehicle is performed to monitor movement signals of the chassis and a rocker arm. Their corresponding power spectral density distributions confirm the correctness of the frequency‐calculation equation. Then, a novel elastic track tensioning device with a damper is designed as a cushion between the idler and the chassis. Depending on its geometry, the equivalent damping coefficient for a dynamic model is evaluated. Subsequently, the damping is altered in response to different operating conditions by a hybrid damping fuzzy semiactive control system. The controller accounts for both chassis and track vibration. Based on the transfer matrix method for multibody systems, a dynamical model of the track system is developed. Control performances are evaluated using two numerical simulations of obstacle crossing and off‐road driving operations. Results indicate that the proposed semiactive tensioner is substantially better than the conventional one. This paper provides a novel feasible scheme for vibration reduction of tracked vehicles.
- 6 March 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 104 (2) , 1139-1155
Contact dynamics analysis of the single-pin meshing pair of a tracked vehicle
- 6 March 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 104 (2) , 1139-1155
Contact dynamics analysis of the single-pin meshing pair of a tracked vehicle