ASAlexey A. Shcherbakov

Alexey A. Shcherbakov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alexey A. Shcherbakov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Energy-Technological Criterion for Managing Milk Cooling Reserve During Power Supply Failures

    by D. N. Savenkov, A. A. Sherbakov, A. A. Mironenko, P. S. Kobylyatsky, Д. Н. Савенков, А. А. Щербаков, А. А. Мироненко, П. С. Кобыляцкий

    Introduction. The quality of dairy products is determined by the cumulative effect of energy parameters and temporal factors within the cooling process. Immediately after milking, prompt reduction of raw material temperature is required, followed by maintaining the specified thermal regime until the transportation or processing stage. Existing energy calculation methodologies applied to milk storage tanks fail to provide a comprehensive framework; it is essential to account for the passive thermal reserve, which is conditioned by the finite heat capacity of both the product and the containment structures, as well as the development kinetics of psychrotrophic microflora. Research indicates that the pre-cooling duration and the transition rate through the high-temperature zone critically influence product quality. Consequently, the evaluation criterion must be dynamic and based on sensor data. The objective of this study is to develop an energytechnological criterion that integrates thermal, microbiological, and electrical reserves to facilitate operational decisionmaking during power supply interruptions. Materials and Methods. An energy-technological criterion has been proposed to evaluate the time reserve during power supply interruptions in a milk storage tank. The criterion incorporates three distinct components: a thermal reserve (con-ditioned by the thermal inertia of both the product heating and the containment structures); a microbiological reserve (determined by the dynamics of microflora growth, accounting for the initial bacterial load); and an electrical reserve (dependent on the capacity of the backup power source and the critical load level). The resulting composite indicator is compared with the forecasted power restoration time: if the forecasted duration exceeds the calculated reserve, emergency response actions are required. Model parameterization involves local identification of the tank’s thermal characteristics and calibration of microbiological dependencies based on empirical data. Research results. An analysis of the temperature margin's sensitivity to key parameters was conducted; the dominant influence of the initial and limiting temperatures was established, driven by the narrow process window. The feasibility of reducing requirements for the thermal storage unit by increasing the passive thermal margin was demonstrated. Taking measurement uncertainty into account, a safety margin based on statistical estimation has been proposed. A dimensionless criterion has been developed to rank process risk zones and formulate an algorithm for management decisions. Model verification involves phased experimental measurements of thermal, electrical, and microbiological parameters, followed by an assessment of predictive accuracy. Discussion and conclusion. The criterion integrates energy and process parameters, providing a transparent assessment of the reserve capacity. Priority measures depend on the limiting factor — whether thermal, microbiological, or electrical. The metric serves as a predictive indicator between laboratory analyses and is applicable to the multi-criteria optimization of costs and risks. Increasing model complexity is justified only if it reduces errors on independent data; otherwise, a simple, conservative model is preferable.

  • Open Access

    Distribution Law of Corrosion of Agricultural Machinery Components under the Influence of Salt Spray

    by Nikolay V. Limarenko, Dmitry N. Savenkov, Dmitry N. Gladkih, Alexey A. Shcherbakov

    Introduction. The development of the agro-industrial complex until 2030 requires increasing the efficiency of the machine and tractor fleet with account for corrosion processes accelerating equipment wear. Existing assessment methods are based on empirical data and do not provide accurate forecasting. The introduction of AI and digital solutions will automate testing, reduce costs and improve the accuracy of assessing degradation caused by corrosion processes. Aim of the Study. The aim is to determine the compliance of experimental data on the effect of salt spray on the corrosion of agricultural machinery components with the distribution law through the example of reversing light switches. Materials and Methods. The object of study was reversing light switches widely used in agricultural machinery. The studies were carried out in a salt spray chamber with parame­ters corresponding to GOST R 52230 and GOST 9.302 for 200 hours with intermediate inspections every 48 hours. During the tests, the degree of corrosion was determined, calculated by the area of damaged sections. Using mathematical methods there was calculated the mean deviation, median, variance, standard deviation, skewness, kurtosis, and range of the sample. Results. As a result of the tests, the operability of the samples was confirmed and the obtained data compliance with the Weibull distribution law was assessed. It was experimentally established that the active phase of surface degradation of reversing light switches increases starting from 96 hours of exposure in the salt spray chamber that is caused by the destruction of protective coatings and progress of pitting corrosion. The use of a quadratic regression model made it possible to describe the dependence of corrosion damage on exposure time. Discussion and Conclusion. The statistical analysis of the sample confirmed Weibull distribution fit that makes it possible to predict further corrosion progress and improve performance assessment of products in salt spray conditions. Obtained parameters allow predicting the resource of components. The results of the study provide a basis for crea­ting digital twins and adaptive maintenance systems using artificial intelligence, which minimize machinery downtime.


  • Open Access

    Distribution Law of Corrosion of Agricultural Machinery Components under the Influence of Salt Spray

    by Nikolay V. Limarenko, Dmitry N. Savenkov, Dmitry N. Gladkih, Alexey A. Shcherbakov

    Introduction. The development of the agro-industrial complex until 2030 requires increasing the efficiency of the machine and tractor fleet with account for corrosion processes accelerating equipment wear. Existing assessment methods are based on empirical data and do not provide accurate forecasting. The introduction of AI and digital solutions will automate testing, reduce costs and improve the accuracy of assessing degradation caused by corrosion processes. Aim of the Study. The aim is to determine the compliance of experimental data on the effect of salt spray on the corrosion of agricultural machinery components with the distribution law through the example of reversing light switches. Materials and Methods. The object of study was reversing light switches widely used in agricultural machinery. The studies were carried out in a salt spray chamber with parame­ters corresponding to GOST R 52230 and GOST 9.302 for 200 hours with intermediate inspections every 48 hours. During the tests, the degree of corrosion was determined, calculated by the area of damaged sections. Using mathematical methods there was calculated the mean deviation, median, variance, standard deviation, skewness, kurtosis, and range of the sample. Results. As a result of the tests, the operability of the samples was confirmed and the obtained data compliance with the Weibull distribution law was assessed. It was experimentally established that the active phase of surface degradation of reversing light switches increases starting from 96 hours of exposure in the salt spray chamber that is caused by the destruction of protective coatings and progress of pitting corrosion. The use of a quadratic regression model made it possible to describe the dependence of corrosion damage on exposure time. Discussion and Conclusions. The statistical analysis of the sample confirmed Weibull distribution fit that makes it possible to predict further corrosion progress and improve performance assessment of products in salt spray conditions. Obtained parameters allow predicting the resource of components. The results of the study provide a basis for crea­ting digital twins and adaptive maintenance systems using artificial intelligence, which minimize machinery downtime.

  • Open Access

    Studying the Thermophysical Characteristics of the Muscle Mass of the Black Soldier Fly Larvaes (Hermetia Illucens) as a Drying Object

    by Valentina A. Doroshenko, Igor A. Khozyaev, Dmitry A. Yakovlev, Artyom A. Doroshenko, Alexey A. Shcherbakov

    Introduction. The main component of the compound feedstuff is fish meal, which has unstable quality and high price. Fish and meat-and-bone meals are replaced with protein concentrates and higher quality larvae proteins. The source of feed protein is the biomass of the black soldier flies (Hermetia illucens), which have a rich amino acid composition and also process food waste. The aim of the work is to study the thermal-physical characteristics of the muscle mass of the black soldier fly larvaes (Hermetia illucens). Материалы и методы. The study focused on the muscle mass of black soldier fly larvaes (Hermetia illucens). The subject of the study is thermal-physical regularities during the drying process. The studies were conducted on the basis of Don State Technical University. The article describes determination of thermal-physical characteristics such as specific heat, thermal conductivity, moisture of the raw material, and oiliness. Results. Heat conductivity coefficient of water 0.555 W/(m∙K) for food and feed products from 0.25 to 0.40 W/(m∙K) black Soldier Fly larvae have a heat conductivity equal to 0.144 W/(m∙K), which is lower than conventional feedstuff components. The humidity of the examined raw material is 45% or higher while the heat conductivity remains linear and practically does not increase. Discussion and Conclusion. The results obtained during the work can be used for parameter determination and design of various types of dryers, and for mathematical description of the dynamics and kinetics of drying.