OBOleksii Burikov

Oleksii Burikov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksii Burikov has a total of 3 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Formation of a microprofile of product surfaces during magneto-abrasive finishing of planes with heads based on high-energy permanent magnets

    by Dmytro Dzhulii, Victor Maiboroda, Oleksii Burikov, Oleksii Belajev

    Experimental studies have been carried out on the possibility of using powder mixtures consisting of large and small particles of various shapes and diamond pastes for magneto-abrasive finishing of flat surfaces of ferromagnetic parts with end heads based on permanent neodymium magnets. It was shown that when using mixtures of powders of shattered shape, the decrease in surface roughness had been obtained from the initial roughness Ra = 0.8 μm to 0.125 μm with a polished microprofile, and the best results occur when the amount of fine fraction in the mixtures does not exceed 40%. The use of mixtures of rounded powders with a particle size of 1700/1200 μm and shattered shape particles of 640/400 μm at their equal amount in the magneto–abrasive tool made it possible to form a surface with a roughness value of Ra=0.1 μm after magneto–abrasive finishing. It has been determined that rounded coarse powders act as a moving lapping tool, transferring the force load to small particles. At the same time, in the process of direct contact with the finished surface, large rounded particles provide both plastic deformation of the surface micro-irregularities and directly of the surface layer of the samples, providing an increase in surface hardness by 1.4 times, which creates favorable conditions for the micro-cutting process with shattered small particles. When forming the magneto-abrasive tool from large rounded particles and diamond paste of different grain sizes, it was found that the best polishing ability is provided by the mixture formed from rounded powder with a particle size of 1500/1300 μm with the addition of diamond paste with a grain size of 5/3 μm. The roughness parameter Ra of the surfaces being finished using such mixtures is 0.03–0.04 μm.

  • Open Access

    Influence of magneto-abrasive machining on the characteristics of the surface layer of flat parts

    by Dmytro Dzhulii, Victor Maiboroda, Oleksii Burikov

    The paper presents the study of the influence of the process of magneto-abrasive machining (MAM) on the characteristics of the surface layers of flat surfaces of parts made of ferromagnetic material U9 by machining with end-type heads based on high-power permanent magnets that form a magneto-abrasive tool of the "brush" type. For estimation of the influence of the process of magneto-abrasive machining on the surface layer, the parameters of surface hardness were analyzed after the machining of test samples with different powders and under different modes. The degree of influence of the MAM on the surface, both in terms of the hardness of the surface layer and the deformation of samples due to compressive residual stresses arising as a result of machining, was studied. The estimation of the state of the surface layer was performed by the change in hardness after machining, the magnitude of the degree of hardening, to some extent, by the parameters of roughness. The control of changes in internal residual stresses formed in the surface layers of samples due to the interaction of powder particles with the surface during machining was carried out according to the degree of their deformation after MAM. It was found that due to MAM, internal compressive stresses of 30–100 MPa arise in the near-surface layer of the material of the samples, while the magnitude of the stresses varied in inverse dependency, that is, with an increase in the working gap, in the vast majority of cases, a decrease in the magnitude of the stresses was observed. It was shown that the depth of the hardened layer under different machining conditions is up to 200 µm or more, and the strengthening coefficient varies from 10 to 40%.