Teemu Peltonen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Teemu Peltonen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Esa Tjukanoff
Department of Information Technology, University of Turku, Lemminkäisenkatu 14 A, FIN-20520, Turku, Finland
4 shared publications - Hannu Tenhunen
School of Information and Communication Technologies, Royal Institute of Technology (KTH), Electrum 229, SE-164 40 Kista-Stockholm, Sweden
4 shared publications - Li-Rong Zheng
School of Information and Communication Technologies, Royal Institute of Technology (KTH), Electrum 229, SE-164 40 Kista-Stockholm, Sweden
3 shared publications - Meigen Shen
Royal Institute of Technology (KTH)
3 shared publications - Tero Koivisto
University of Turku
3 shared publications - Cheng Tao
Department of Information Technology, University of Turku, Joukahaisenkatu 3-5 B, 20520 Turku, Finland;; Tel: +358-2-3338646; Fax: +358-2-3338600
1 shared publication
Latest Publications
- 1 December 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1409-1414
RF Transceiver Circuit Technology Based Wireless Interconnects for Inter- and Intra-Chip Communication System
In this work, some most frequently studied interconnect solutions in recent years have been discussed and compared to show their advantages and limitations. RF wireless interconnect (RFWI) method is further studied by system modeling in simulink environment and successful communication between transmitter and receiver is obtained. The results indicate the potential feasibility and reliability of the inter-chip and intra-chip communication system using integrated RF transceiver and antenna to replace the present metal wiring interconnect. The fact that lots of the existing experiences on RF transceiver and antenna design makes RFWI an attractive interconnect solution.
- 1 December 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1409-1414
RF Transceiver Circuit Technology Based Wireless Interconnects for Inter- and Intra-Chip Communication System
In this work, some most frequently studied interconnect solutions in recent years have been discussed and compared to show their advantages and limitations. RF wireless interconnect (RFWI) method is further studied by system modeling in simulink environment and successful communication between transmitter and receiver is obtained. The results indicate the potential feasibility and reliability of the inter-chip and intra-chip communication system using integrated RF transceiver and antenna to replace the present metal wiring interconnect. The fact that lots of the existing experiences on RF transceiver and antenna design makes RFWI an attractive interconnect solution.
- 1 January 2007
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 50 (1) , 47-57
UWB radio module design for wireless sensor networks
- 1 January 2007
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 50 (1) , 47-57
UWB radio module design for wireless sensor networks
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
UWB Radio Module Design for Wireless Intelligent Systems-From Specification to Implementation
In this paper, we designed an impulse-based ultra wideband (UWB) radio module (low band) for wireless intelligent system applications such as radio frequency identification (RFID) and wireless sensor networks (WSN). The UWB radio module includes transceiver block, baseband process unit and power management block. The transceiver circuits include Gaussian pulse generator, wideband low noise amplifier (LNA), multiplier, integrator and timing circuits, which use 0.18mum, 1P6M CMOS technology. The wideband LNA has a power gain of 10dB and minimum noise figure of 2.7dB. For UWB transceiver, the power consumption of transmitter is lower than 1mW while the receiver is about 23mW. The liquid-crystal-polymer (LCP)-based system-on-package (SoP) technology is used to implement the UWB radio module for low power, low cost and small size
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
UWB Radio Module Design for Wireless Intelligent Systems-From Specification to Implementation
In this paper, we designed an impulse-based ultra wideband (UWB) radio module (low band) for wireless intelligent system applications such as radio frequency identification (RFID) and wireless sensor networks (WSN). The UWB radio module includes transceiver block, baseband process unit and power management block. The transceiver circuits include Gaussian pulse generator, wideband low noise amplifier (LNA), multiplier, integrator and timing circuits, which use 0.18mum, 1P6M CMOS technology. The wideband LNA has a power gain of 10dB and minimum noise figure of 2.7dB. For UWB transceiver, the power consumption of transmitter is lower than 1mW while the receiver is about 23mW. The liquid-crystal-polymer (LCP)-based system-on-package (SoP) technology is used to implement the UWB radio module for low power, low cost and small size
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A 0.18 μm CMOS Ultra-Wideband Low-Noise Amplifier with High IIP3
In this paper an ultra-wideband low-noise amplifier (LNA) for the frequency range of 3.1 - 9.4 GHz using 0.18 mum CMOS RF process is introduced. Single-ended single stage LNA structure utilises an input LC-ladder, cascode transistor configuration and LRC-feedback to realise an ultra broad bandwidth response. In operating frequency range noise figure (NF) of 3.1 dB and gain of 10.6 dB were achieved along with high linearity (IIP3) even up to 10.9 dBm at 3.1 GHz. With the bias network, the LNA had a total power consumption of 31 mW from 1.8 V supply
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A 0.18 μm CMOS Ultra-Wideband Low-Noise Amplifier with High IIP3
In this paper an ultra-wideband low-noise amplifier (LNA) for the frequency range of 3.1 - 9.4 GHz using 0.18 mum CMOS RF process is introduced. Single-ended single stage LNA structure utilises an input LC-ladder, cascode transistor configuration and LRC-feedback to realise an ultra broad bandwidth response. In operating frequency range noise figure (NF) of 3.1 dB and gain of 10.6 dB were achieved along with high linearity (IIP3) even up to 10.9 dBm at 3.1 GHz. With the bias network, the LNA had a total power consumption of 31 mW from 1.8 V supply